41410X User Manual

Loading ...

NOTE: Opener MUST be mounted to garage framing material. DO NOT install to particle board or drywall.

The instructions above are provided using standard wood framing and bracing. Additional bracing may be required for this installation.

Hardware for masonry or steel construction is not provided.

Level & Square

Opener

2) Mount opener to wall.

3) Level and square opener.

NOTE: Vertical lift openers will not be level.

4) Leave at least a 1/4” gap between coupler and door shaft bearing.

5) Mark mounting bracket hole position, pre-drill a 3/16” pilot hole and install lag screw and fully tighten.

6) Add 1 full turn to hollow tube or 1/2 turn for solid shaft on each coupler set screw in 1/4 turn increments after contacting door and

opener shaft surfaces. DO NOT tighten set screws into an empty keyway.

7) Adjust opener to ensure back of opener is ush with wall and tighten mounting bracket bolt to opener.

8) Pull emergency release cable and manually operate door to inspect for binding. (Pull cable until it clicks and locks into place. Pull

again to release and lock opener to door).

9) Tie RED emergency release cord to cable loop and tie release handle to cord approximately 6 feet from oor.

INSTALLING THE OPENER (CONT’)

At least

1/4” Gap

3/8”

WRENCH

1. Level Opener

2. Mark

3. Pre-Drill

4. Install Lagbolt

7/16”

SOCKET

3/16”

Bit

NOTE: Ensure all COUPLER BOLTS are secured prior to tightening mounting bracket bolt.

INSTALLING WIRELESS WALL CONSOLE

1. Plug door lock harness into the LOCK plug on bottom of opener. Insert plug in correct direction (SEE INSET)

2. Run wire down the wall to the DOOR LOCK and secure with supplied wire staples. NOTE that DOOR LOCK wires are polarity sensitive.

3. Cut o excess wire, strip 1/4” of insulation and attach to bottom connectors on DOOR LOCK.

4. Install WHITE wire to W terminal and STRIPED wire to B/W terminal.

Wire Door Lock

WIRE DOOR LOCK

ALL WIRE CONNECTIONS LOCATED AT BOTTOM OF OPENER

Door lock prevents manual door operation and is important for garage security

Door lock should be installed no more than 10 feet away on the opener side of the door if possible.

1. Mount door lock onto door track above a roller on the second or third door panel from the oor.

If mounting position does not line up with pre-punched door lock bar cutouts as shown below:

•Remove template from the back page of the owners manual.

•Apply template to the door track where the center 7/16” hole is approximately 3 inches above the door roller on the 2nd or 3rd door panel.

•Drill two 9/32” holes for mounting and one 7/16” hole if using template. De-burr holes if required.

2. Position door lock and install two 1/4” X 9/16” track bolts and nuts. Install track bolt on inside of door track facing outward.

9/32”

7/16”

Bit

INSTALL DOOR LOCK

7/16”

SOCKET

Door Lock Plug

Door Lock Wire Connections

1. Position Safe-T-Beam

(STB) Transmitter and Receiver on each side of garage door 5"- 6" above oor. Face the lenses towards each

other. (See inset on locating Safe-T-Beam® sets)

2. Mark bracket mounting holes; drill 3/32" pilot holes and secure with 1/4" x 1-1/4" lag screws (provided) into wood. If mounting into

concrete or block, other fasteners are required and are available at leading retail stores.

3. Route 2 lengths of supplied wire from powerhead, down to one sensor and along the header and down the side of the door to the

other sensor. Secure the wire to the walls using the insulated staples.

4. On the powerhead: Remove 1/4" insulation from both sets of white and striped wire. Twist two white wires together. Using a small

at head screwdriver, press in the orange tab at one STB terminal and insert the wires. Twist the two striped wires together and

insert into the other STB terminal. NOTE that STB wires are not polarity sensitive.

5. At each sensor, remove 1/4" insulation from the white and striped wires and secure in each screw terminal.

6” max

5” min

above ﬂoor

6” max

5” min

above ﬂoor

Floor mount option

PHOTOCELL (STB)

Wall mount

Transmitter/Receiver

To powerhead

Install and Wire Safe-T-Beams® (STB)

INSTALL SAFE-T-BEAM® SYSTEM

5 6

7 8

Install Bluetooth® Light Fixture

Install Wireless Wall Console

1. Determine mounting location within 30 feet of opener.

2. Pre-drill 3/32” holes for mounting screws, or 3/16” if using drywall anchors (supplied) if needed. 7-1/2 in. inches apart.

3. Install supplied screws leaving an 1/8” gap for mounting.

4. Route power cord through cutouts in ange and plug light into a standard 115V outlet. Secure excess wire under light housing.

5. Align LIGHT FIXTURE mounting holes with screws and turn light assembly to lock into place.

1. Determine mounting location for wireless wall console.

•Mount console no less than 5 feet above oor to prevent small children from activating opener.

2. Pre-drill 3/32” holes for mounting screws, or 3/16” if using drywall anchors (supplied) if needed.

3. Install screw leaving a 1/8” gap.

4. Slide console onto screw and down slightly to lock in place.

5. Remove battery door and remove protective tab and batteries.

6. Install screw to secure console to the wall.

7. Install batteries and battery door.

8. Install warning decal in the same area as wireless wall console.

AAA

1. DOOR Button - Runs garage door opener.

2. DELAY Button - Adds a 10+ second delay for door operation. Press the delay button and door

will automatically operate after set delay. Can be activated up to 3 times for a 10, 22 or 30

second delay.

3. LIGHT Button - Overrides the automatic timed light function of the garage door opener.

Wall Console Operation

7-1/2 in.

LIGHT FIXTURE INCLUDED WITH OPENER:

1. Power up Wall Mount Opener.

2. Power LIGHT FIXTURE.

Light will automatically pair when opener is powered up.

3. LIGHT FIXTURE will ash and beep briey.

4. LIGHT FIXTURE will ash again indicating that it is now paired to the opener.

Wireless Wall Console will automatically pair when opener is powered up.

INSTALL BOTTOM COVER OR BATTERY BACKUP

DO NOT Apply power to opener. Read and understand owners manual before proceeding

Install Bottom Cover Onto Opener - OMIT THIS STEP IF INSTALLING BATTERY BACK-UP

1. Remove two screws on the sides or bottom of opener depending on the version of cover supplied.

2. Route wires to the rear of opener to align with slot in rear of cover.

3. Install cover with screws removed in step 1.

Peal DOOR LOCK

template decal from back

of owners manual and

transfer to door track

Approx. 3”

Wall

1/8 "

Screw

head gap

SEE FULL INSTRUCTION SHEET INCLUDED WITH WIRELESS WALL CONSOLE FOR DETAILED INSTALLATION AND OPERATION INFORMATION.

SEE FULL INSTRUCTION SHEET INCLUDED WITH LIGHT KIT FOR DETAILED INSTALLATION AND OPERATION INFORMATION.

INSTALLING BLUETOOTH® LIGHT KIT

1/8"

Screw

head gap

IF INSTALLING A BATTERY BACKUP, SEE BATTERY BACKUP INSTALLATION INSTRUCTIONS IN THE “SPECIAL

INSTALLATION INSTRUCTIONS” SECTION OF THE OWNERS MANUAL.

FINISHING THE INSTALLATION

DO NOT OPERATE THIS OPENER AT THIS TIME.

SEE INSTRUCTION MANUAL FOR FURTHER INSTRUCTIONS.

SETTING THE DOOR DRUM SIZE AND TRAVEL LIMITS IS CRITICAL TO

SAFE AND PROPER OPERATION.

FAILURE TO PERFORM SET UP PROCEDURES CAN RESULT IN OPENER

AND DOOR DAMAGE!

NEED HELP OR HAVE QUESTIONS?

DO NOT RETURN product to the store.

Call Genie: 1-800-35-GENIE or visit www.GenieCompany.com

STOP STOP

LOCATING SAFE-T-BEAM® for multiple doors

Transmitter (RED LED) and Receiver (GREEN LED)

Emergency

Release

OPEN DOOR BEFORE DRILLING

TO PREVENT DOOR DAMAGE

Pull release cable until it

clicks to reset and lock

opener to door.

Loading ...

User Manual - Page 11