Loading ...
Loading ...
Loading ...
Fig. 3 Fig. 5
CLEANING YOUR Hydro Spa
1) Clean your Hydro Spa after each use by wiping with a clean cotton cloth. Do not immerse
the entire unit in water.
2) Clean your unit periodically by wiping it with a damp cotton cloth.
RECOMMENDED USE TIME
We recommend using the Jet Hydro Spa for 15-20 minutes at a time.
HOW TO ATTACH YOUR Hydro Spa TO YOUR TUB
1) Make sure the power knob is in the OFF position. The tub should be clean and empty of
water.
2) Extend the folding arm and position unit along edge of tub so the unit is inside the tub and
the arm is resting on edge (Fig. 3).
3) Moisten suction cups on motor housing of Hydro Spa to increase grip.
4) Secure suction cups by gently applying even pressure on Hydro Spa against tub wall
(Fig. 3).
5) Adjust suction cup on arm so that it adheres directly onto bathtub edge. See Fig. 4 and
following “Suction Cup Position Adjustment” section (Fig. 6).
6) Adjust height of motor assembly to desired depth by moving motor housing up or down
by hand. Built-in detents will hold the position you desire (Fig. 5).
7) Water may spray if unit is not level when turned on.
Fig. 4
Please register this product at register.conair.com
SERVICE CENTER
Conair LLC
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
Visit us on the web at: www.conair.com
©2022 CONAIR LLC
stock.image
HYD100
22PS084456
IB-17743
SUCTION CUP POSITION ADJUSTMENT
Suction cup underneath the handle can be in one of two positions to suit different bathtubs
(see Fig. 6).
Push and slide the suction cup to the desired position.
Position A: The outermost position for thick-sided tubs.
Position B: The innermost position for thin-sided tubs.
FITTING AND REMOVING FILTER CAPS
TO REMOVE CAPS
1) Filter caps are located on either side of the motor assembly.
2) Turn cap about 20° counterclockwise (Fig. 7).
3) Line up single hash mark on cap with the center
seam on the back body of the unit.
4) Pull cap away from unit.
5) Rinse cap under water to remove hair, lint, etc.
TO REPLACE CAPS
1) Push cap into body so that single hash mark on cap lines up with the center seam on the
back body of the unit.
2) Turn cap clockwise about 20° until the double hash marks on the cap line up with the
center seam on the back body of the unit.
WARNING: To help prevent excess lint, hair, etc., from getting caught in motor, unit
should never be used with the filter cap removed. Injury or damage to unit could result.
LIMITED ONE-YEAR WARRANTY
(U.S. and Canada Only)
Conair will repair or replace (at our option) your appliance free of charge for 12 months from
the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed,
together with your sales receipt. California residents need only provide proof of purchase
and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase
receipt, the warranty period will be 12 months from the date of manufacture. ANY IMPLIED
WARRANTIES, OBLIGATIONS OR LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS
WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation
of special, incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state.
Position B
Fig. 6
Position A
Fig. 7
FEDERAL COMMUNICATIONS COMMISSION NOTICE
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
SUPPLIER’S DECLARATION OF CONFORMITY
Brand: CONAIR
Model No.: HYD100
Description: JET HYDRO SPA
Responsible Party: Conair LLC, 1 Cummings Point Road, Stamford, CT 06902
1-800-334-4031
Standards: FCC Part 15 Subpart B, ANSI C63.4-2014
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesirable
operation.
DATE OF ISSUE: April 27, 2022