Loading ...
Loading ...
Loading ...
10
5. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A19) is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
(A7) and is collected in the drip tray (A12) underneath. Avoid
contact with splashes of water.
• To turn the appliance on, press the button (B1 - g.
9). The message “Heating up, Please wait” appears on the
display (B4).
When heating is complete, the message changes to “RINSING”.
As well as heating the boiler, this also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coee appears.
6. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A7). Avoid contact with splashes of water.
• To turn the appliance o, press the button (B1 - g.
9).
• The message “Turning o underway Please wait” appears
on the display (B4), then the appliance performs a rinse
cycle and goes o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button;
• release the main switch (A19) at the back of the appliance
(g. 2).
Important!
Never press the main switch while the appliance is on.
7. MENU SETTINGS
7.1 Rinsing
Use this function to deliver hot water from the coee spouts
(A7) and hot water spout (C6), if inserted, to clean and heat the
appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coee and hot water spouts (g. 8).
To enable the function, proceed as follows:
1. Press the MENU/ESC button (B2) to enter the menu;
2. Press (B9) or (B10)
(g. 6) until “Rinsing” appears on
the display (B4);
3. Press the OK button (B3 - g. 7): the message “Conrm?” is
displayed;
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the OK button. “RINSING Please wait” is displayed;
5. After a few seconds, hot water is delivered rst from the
coee spouts, then from the hot water spout (if inserted) to
clean and heat the appliance’s internal circuit. “RINSING” is
displayed, together with a progress bar which lls gradually
as preparation proceeds;
6. To stop the process press any button or wait for delivery of
water to stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, we
strongly recommend, when switching on the appliance,
performing 2/3 rinses before using it;
• After cleaning, it is normal for the coee grounds container
(A10) to contain water.
7.2 Descaling
For instructions on descaling, see section “12. DESCALING”.
7.3 Installing the lter
For instructions on how to install the lter, see section “14.
WATER SOFTENER FILTER”.
7.4 Replacing the water softener lter (if
installed)
For instructions on how to replace the lter, see section “14.2
Replacing the lter”.
7.5 Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button (B2) to enter the menu;
2. Press (B9) or (B10)
(g. 6) until “Adjust time” appears
on the display (B4);
3. Press the OK button (B3 - g. 7): the hours ash on the
display;
4. Press or to change the hour;
5. Press the OK button to conrm. The minutes ash;
6. Press or to change the minutes;
Loading ...
Loading ...
Loading ...