Loading ...
Loading ...
Loading ...
Proper Air Circulationr
• To ensure your refrigerator works at the maximum efficiency it was designed for, you should install it
in a location where there is proper air circulation, plumbing and electrical connections
• Leave a space with an open angle of 160 ° for opening the door.
• The following are recommended clearances around the refrigerator:
Sides....................4” (10 cm)
Top.......................4” (10 cm)
Back......................8” (20 cm)
Electrical Requirement
• Make sure there is a suitable power outlet with proper grounding to power the refrigerator. This unit
uses AC110V-120V / 60Hz power, there should be a 500va stabilizer if the voltage luctuation exceed
98V-127V / 60Hz respectively.
• Avoid the use of three prong adapters or cutting off the third grounding prong in order to accommodate
a two prong outlet. This is a dangerous practice since it provides no effective grounding for the
refrigerator and may result in shock hazard.
Use of Extension Cords
• Avoid the use of an extension cord because of potential safety hazards under certain conditions. If it is
necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug
and a 3-slot outlet that will accept the plug. The marked rating of the extension cord must be equal to or
greater than the electrical rating of the appliance.
Installation Limitations
• Do not install your refrigerator in any location not properly insulated, this refrigerator was not designed
to operate in temperature settings below 55˚ Fahrenheit.
• Select a suitable location for the refrigerator on a hard even surface away from direct sunlight or heat
source, e.g. radiators, baseboard heaters, cooking appliances, etc. Any floor unevenness should be
corrected with the leveling legs located on the front bottom corners of the refrigerator.
PROPER REFRIGERATOR CARE AND CLEANING
WARNING
To avoid electric shock, always unplug your
refrigerator before cleaning. Ignoring this warning may result in death or injury.
CAUTION
Before using cleaning products, always read and follow manufacturer’s instructions and warnings
to avoid personal injury or product damage.
CLEANING
Prepare a cleaning solution of 3-4 tablespoons of baking soda mixed with warm water. Use sponge or
soft cloth, dampened with the cleaning solution, to wipe down your refrigerator.
• Rinse with clean warm water and dry with a soft cloth.
• Do not use harsh chemicals, abrasives, ammonia, chlorine bleach, concentrated detergents, solvents or
metal scouring pads. Some of these chemicals may dissolve, damage and/ or discolor your refrigerator.
DOOR GASKETS
Clean door gaskets every three months according to general instructions.
Gaskets must be kept clean and pliable to assure a proper seal.
• Remove gasket from the door, wash, dry and seal it as before. Putting some talcum powder on
the magnetic surface would prolong its service life.
• Petroleum jelly applied lightly on the hinge side of gaskets will keep the gasket pliable and
ensure a good seal.
BULB REPLACEMENT
Remove the lamp shade, take out the bulb, replace with a new one, then remount the lamp shade.
POWER INTERRUPTIONS
Occasionally there may be power interruptions due to thunderstorms or other causes. Remove the power
cord from AC outlet when a power outage occurs. When power has been restored, replug power cord to
AC outlet. If outage is for a prolonged period, inspect and discard spoiled food in refrigerator.
Clean refrigerator before reusing.
VACATION AND MOVING CARE
For long vacations or absences, empty food from refrigerator, move the temperature dial to
the "0" position and clean the refrigerator and door gasket according to "General Cleaning" section.
Prop doors open, so air can cir-culate inside.When moving, always move the refrigerator vertically.
Do not move with the unit lying down. Possible damage to the sealed system could occur.
ENERGY SAVING TIPS
• The refrigerater should be located in the coolest area of the room, away from heat-producing appliances
or heating ducts, and out of direct sunlight.
• Let hot foods cool to room temperature before placing in the refrigerator. Overloading the refrigerator
forces the compressor to run longer and thus increases energy consumption. Foods that refrigerate
too slowly may lose quality or spoil.
• Be sure to wrap foods properly, and wipe containers dry before placing in the refrigerator.
• The wire shelves should not be lined with aluminum foil, wax paper, or paper towels.
Liners interfere with cold air circulation, making the refrigerator less efficient.
• Organize food to reduce door openings and extended searches. Remove as many items as needed at
one time, and close the door as soon as possible.
5
INSTALLATION (cont.)
4
Loading ...
Loading ...
Loading ...