Loading ...
Loading ...
Loading ...
Using the Manual Siphon Pump
taned the Vacuum
Release Knob on the
Siphon Pump Bulb by
turning it CLOCKWISE, _GHTEN
After the Fuel Tank has
Ioeen properly filled, turn the Vacuum Release Knob
COUNTER-CLOCKWISE to drain the Siphon.
3. The Fuel Tank ts
properly filled when the
needle on the luei
gauge is on _'F',
DO NOT OVERFILL the
Fuel Tank.
4. Replace the Fuel Cap and hand tighten,
5. BEFORE USING THIS HEATER FOR THE FIRST
TIME MAKE SURE TO FILL THE FUEL UNTIL THE
POINTER MOVES TO °F" AND WAlT FOR AT LEAST
30 MINUTES BEFORE LIGHTING
This time allows the Wick to absorb enough fuet for
satisfactory lighting and burning
NOTE: It the heater is ignited in tess than 30 mlnules
after the tank is filled, the flame may persFst
weakly for a short while and then may exhngu_sb
itself.
• Lighting the Heater
1. After waiting for n,_ _
NOT LESS than 30 min- •
ute@, raise the Wick to
Its full height by turning
the Wick Adjustment
Knob CLOCKWISE to
the "HIGH'" position un-
til it comes to a firm @top
2. Gently press the Ig- _ _ _ _'_lll=
nitlon Lever DOWN. m_ i
Hold the Laver in place ___._.__._._
until the flame appears.
(Approximately 3 to 5
• econds). Then gently
release the Ignition
Lever.
NOTE: Pressing the Ignition Lever too hard will push
the Ignition Plug too deeply into the Wick and
will produce white smoke instead of a ctean ig-
nition, if this Occurs. release the pressure On the
Ignition Lever slightly Holding the lever in
place too long wtft produce smoke and odor, Be
certain the Ignition Plug is fully retracted after
lighting the heater.
3. After the Wick is lighted, check the alignment of the
Burner by rotating it LEFT and RIGHT two or three times
4. DO NOT OPERATE THE IGNITER WHILE THE
HEATER IS IN OPERATION. YOU WILL DAMAGE THE
WICK AND THE IGNITION PLUG AND PRODUCE
SMOKE AND ODOR.
'- Adjusting the Wick Du[ing Operation
After the heater is IlL it will warm gradually until it
reaches full heating power This normally takes ten to fif-
teen minutes. You can controt your heater's output by
using the Wick Adjustment Knot) to raise or lower the
Wick,
WARNING; Risk of {ndoor air pollution and fire. DO not
Operate heater at a wick _.elting lower than the m_nimum
wick-stop setting.
1. Set the WIck Adjustment Knob to _he "Nigh"
position
2. When your heater is
prOpedy adjusted, the
flame witl burn in an
evenly balanced circle
_'* to _'," over top of the
Burner
3, if the flame touches
the walt of the heater,
the Wick IS adjusted too
high. NOTE: Smoke
and odor will be pro-
duced when flame is
too high.
FLAME
TOO
PIIGH
Turn the Wick Adlustme#t Kr_ob COUNTEd-CLOCKWiSE
_n _he direCt;On Of ¸'LOW¸¸
a00earatth0tOpOflhe!
Burner, the "Wick _s ad.
justed tOO low. Smoke TOO
and soot may result if LOW
heater te operated w_th __ ---- _f .........
the flame 1oo tow.
Tutr_ _he W_Ck A_justme_1 Knob OLOCKWISE _r_ _ne
d_fect_or_ of "HIGH ¸¸
5. NEVER operaze your Heate_ below the ¸'LOW'"
Seeing indicated or_ lh_ fro_t _anel of the Heater
NOTE: It the flame wavers, burros too high or_ one side,
o{ smokes, adjust the Burr_er to make sure
t_at it is _rooerly seateo, centered in the Correct
13osit_on and not m_sahgned or_ the Wick,
HOLJS_n_j F_liure to proDerly 13osttion the BtJtner
[t_y _,_use th_ Heater to o{3er_te _mDro_erly
Loading ...
Loading ...
Loading ...