Loading ...
Loading ...
Loading ...
Operation Guide 5580
E-79
Moving the Hands for Easy Viewing of the Digital Dials
You can use the procedure below to move the analog hands in order to better view a
digital dial.
Note
• The analog hands will not move while battery power is low.
• Time calibration signal reception is disabled while the hands are in positions to
allow easier viewing of the digital dials (page E-80).
E-78
Note
• After performing home position adjustment, enter the Timekeeping Mode and check
to make sure that the analog hands and the digital dial indicate the same time. If
they do not, perform home position adjustment again.
E-77
• The watch will return to regular timekeeping automatically if you do not perform
any operation for about two or three minutes. Any changes you have made to
settings up to that point will be saved.
If the hour and minute hands are all at 12 o’clock, which is their home position,
jump to step 3.
2. Use
D
(+) and
B
(–) to adjust the hour and minute hand positions.
• Holding down either button will cause the hand to move at high speed. Once
started, high-speed hand movement will continue even if you release the button.
To stop high-speed hand movement, press any button.
• High-speed hand movement started with the
D
(+) button will stop automatically
after 12 revolutions of the minute hand. If started with the
B
(–) button, it will
stop after one revolution of the minute hand.
3. Press
A
to exit home position correction and return to regular timekeeping.
E-76
Hand Home Position Adjustment
Strong magnetism or impact can cause the hands of the watch to be off, even if the
watch is able to perform the signal receive operation.
• Home position adjustment is not necessary when the analog time and digital time
are the same time in the Timekeeping Mode.
To adjust home positions manually
1. In the Timekeeping Mode, hold down
A
and keep it depressed for about five
seconds until
H.SET
appears in the right digital dial.
• The hour and minute hands should all move to 12 o’clock, which is their home
position.
• Though ADJ will appear in the right digital dial about two seconds after you hold
down
A
, do not release the button yet. Keep it depressed until H.SET appears.
When H.SET appears in the right digital dial, release the
A
button. This will
cause the hour and minute hands to move to 12 o’clock.
E-75
• Illumination may not turn on if the face of the watch is more than
15 degrees above or below parallel. Make sure that the back of
your hand is parallel to the ground.
• Illumination turns off after the preset illumination duration (page E-69),
even if you keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper
operation of the auto light switch. If illumination does not turn on, try
moving the watch back to the starting position (parallel with the
ground) and then tilt it back towards your face again. If this does
not work, drop your arm all the way down so it hangs at your side,
and then bring it back up again.
• You may notice a very faint clicking sound coming from the watch
when it is shaken back and forth. This sound is caused by
mechanical operation of the auto light switch, and does not indicate
a problem with the watch.
E-74
Illumination Precautions
• LED panel that provides illumination loses power after very long use.
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of
your arm can cause frequent activation of the auto light switch and illumination of
the face. To avoid running down the battery, turn off the auto light switch whenever
engaging in activities that might cause frequent illumination of the face.
• Note that wearing the watch under your sleeve while the auto light switch is turned
on can cause frequent illumination of the face and can run down the battery.
E-73
To turn the auto light switch on and off
In the Timekeeping Mode, hold down
B
for about three
seconds to toggle the auto light switch on (indicator
displayed in the right digital dial) and off (indicator not
displayed).
• The auto light switch on indicator appears in all modes
while the auto light switch is turned on.
• The auto light switch turns off automatically whenever
battery power drops to Level 4 (page E-15).
Auto light switch on
indicator
E-72
Note
• This watch features a “Full Auto Light”, so the auto light switch operates only when
available light is below a certain level. It does not illuminate the display under bright
light.
• The auto light switch is always disabled, regardless of its on/off setting, when any
one of the following conditions exists.
While an alarm is sounding
While a receive operation is in progress
E-71
About the Auto Light Switch
Turning on the auto light switch causes illumination
to turn on, whenever you position your wrist as
described below in any mode.
Moving the watch to a position that is parallel to
the ground and then tilting it towards you more
than 40 degrees causes illumination to turn on.
Warning!
•
Always make sure you are in a safe place whenever you are reading the face
of the watch using the auto light switch. Be especially careful when running or
engaged in any other activity that can result in accident or injury. Also take
care that sudden illumination by the auto light switch does not startle or
distract others around you.
•
When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
More than
40°
Wear the watch on the
outside of your wrist
E-70
2. Use
C
to cycle through the settings in the right digital dial until the current
illumination duration (
LT1
or
LT3
) is shown.
• See the sequence in step 2 of the procedure under “To change the current time
and date settings manually” (page E-48) for information about how to scroll through
setting mode.
3. Press
D
to toggle the illumination duration between three seconds (
LT3
displayed)
and 1.5 seconds (
LT1
displayed).
4. After all of the settings are the way you want, press
A
to exit the setting mode.
• Exiting a setting mode will normally cause the hands to return to regular
timekeeping automatically. However, if you manually move the hands (page E-80)
and then enter a setting mode, they will not return to regular timekeeping
automatically when you exit the setting mode. In this case, you will need to return
the hands to their normal positions manually (page E-81).
Loading ...
Loading ...
Loading ...