Hertz HMX 8-S-LD-SW Owner's Manual

Owner's Manual - Page 20

For HMX 8-S-LD-SW. Also, The document are for others Hertz models: HMX 6.5, HMX 6.5-C, HMX 6.5-LD, HMX 6.5-LD-C, HMX 6.5-TC, HMX 6.5-TW, HMX 6.5-LD-TC, HMX 6.5-LD-TW, HMX 6.5 S, HMX 6.5 S-LD, HMX 8, HMX 8-C, HMX 8-LD, HMX 8-LD-C, HMX 8-TC, HMX 8-TW, HMX 8-LD-TC, HMX 8-LD-TW, HMX 8 S, HMX 8 S-LD, HMS 10 B, HMS 10 B-C, HMS 10 B-C2, HMS 10 B-2, HMS 10 S-LD-G, HMS 10 S2-LD-G

Loading ...

FUSE

RED

GREEN

BLUE

YELLOW (+ 12 V)

+ 12 Vdc

Switched +12V

GND

*250 mA only for

HMS 10 S-LD-G /

HMS 10 S2-LD-G

100 mA or

*250 mA

100 mA or

*250 mA

100 mA or

*250 mA

2 Speakers

1 Speaker

N Speakers

100 mA

x N Speaker

*250 mA

x N Speaker

COLOR RED GREEN BLUE

WHITE X X X

RED X

GREEN X

BLUE X

YELLOW X X

PURPLE X X

CYAN X X

LED CIRCUIT WIRING

- Voltage provided to the LED circuit must not exceed +12,5 Vdc referred to the system ground (GND).

- Voltage provided to the LED circuit should be switched by an activation circuit in order to turn-on the LED lighting only when

required and turn it off when vessel is not used or put into storage.

- Protect the YELLOW (+12V) wire with a 100mA fuse, then connect the YELLOW (+12V) wires from all the speakers together to the

main Switched +12 Vdc.

- Fuse the Switched +12 Vdc according to the total number of speakers connected

in parallel. We suggest for the fuse value to be as close

as possible to the standard

value corresponding to 100mA or 250 mA x N speakers rounded in excess. I.e. 6 speakers (3 pairs) in parallel

requires 100mA x 6 = 600mA, for which the closest standard fuse value rounded in excess would be 630mA.

- Connect the R(Red), G(Green), B(Blue) wires from the speaker to the system ground (GND) referring to the below table according

to the color desired among the 7 available options.

COLLEGAMENTO DEL CIRCUITO LED

- La tensione fornita al LED non deve superare i 12,5 Vdc riferiti a massa (GND).

- La tensione fornita al LED dovrebbe essere controllata da un circuito di attivazione (+12V Switched) per accendere il LED solo

quando necessario e spegnerlo quando l’imbarcazione non viene utilizzata o rimessa.

- Proteggere con un fusibile da 100mA il cavo YELLOW (+12V), poi connettere insieme i cavi YELLOW (+12V) di tutti gli speaker al circuito

di attivazione (+12V Switched).

- Proteggere con un fusibile la tensione fornita dal circuito di attivazione (+12V Switched), il valore del fusibile deve essere calcolato

con la formula 100mA o 250 mA x N Speaker con il risultato approssimato al valore di fusibile standard più vicino. Esempio 6 speaker

(3 coppie) in parallelo richiedono 100mA x 6 = 600mA per il quale il valore standard più vicino è 630mA.

- Collegare i cavi R(Red), G(Green), B(Blue) dallo speaker al sistema di massa (GND) seguendo la tabella sotto in funzione del colore

desiderato tra i 7 disponibili.

HMX 6.5-LD / HMX 6.5-LD-C / HMX 6.5-LD-TC / HMX 6.5-LD-TW / HMX 6.5 S-LD / HMX 8-LD

HMX 8-LD-C / HMX 8-LD-TC / HMX 8-LD-TW / HMX 8 S-LD / HMS 10 S-LD-G / HMS 10 S2-LD-G

LED direct wiring

Loading ...

Hertz HMX 8-S-LD-SW 8" Hi-End Marine RGB LED Coaxial Speaker Pair

Owner's Manual - Page 20