INSTRUCTION MANUAL
16 INCH METAL STAND FAN
MODEL NO: FD-40M
Read all instructions before using this appliance. Carefully
retain these instructions for future reference
1
GENERAL CARE AND SAFETY GUIDE
● Use only the voltage specified on the rating plate of the fan.
● Do not cover or restrict airflow to the inlet or exhaust grilles in
any manner as the appliance may overheat and become a fire
risk.
●NEVER cover the fan:this may cause fire.
●Do not block air inlets or outlets in any manner.Check the
openings from time to time for accumulated dust.
●Ensure long shag carpet does not obstruct airflow under the unit.
●Do not place appliance close to a radiant heat source.
●Do not operate in area where gasoline,paint or other flammable
liquids are used or stored.
●Do not insert or allow foreign objects to enter any ventilation or
exhaust opening,as this may cause an electric shock,fire or
damage to the appliance.
●Do not operate any appliance with a damaged cord,plug or after
the appliance malfunctions or has been dropped or damaged in
any manner.Return to a qualified electrical person for
examination,electrical or mechanical adjustment,service or repair.
●This appliance is intended for household use only and not for
commercial or industrial use.
●Use this appliance only as described in this manual.Any other
use is not recommended by the manufacturer and may cause
fire ,electric shock or injury.
●Do not use abrasive cleaning products on this appliance.Clean
with a damp cloth(not wet) rinsed in hot soapy water only.Always
remove plug from the mains supply before cleaning.
●Do not connect the appliance to the mains voltage until
completely assembled and adjusted.
●Switch off and use handles where provided when moving.
2
●Always operate on a flat horizontal surface.
●Do not remove plug from power socket until the appliance has
been switched off.
●Do not remove plug from power socket by pulling flex-always
grip plug.
●Always unplug appliance when not in use.
●Do not allow cord to come in contact with heated surfaces during
operation.
●Do not run cord under carpeting,throw rugs or runners
etc.Arrange cord away from traffic areas so that it will not be
tripped over.
●Do not twist,kink or wrap the cord around the appliance,as this
may cause the insulation to weaken and split.
●Important-This fan is damaged ,it must be replaced by the
manufacturer, its service agent or a similarly qualified person in
order to avoid a hazard.
●Do not operate the fan near to curtains or any other fabric which
could be sucked into the fan unit.
●Ensure that the fan is switched off from the supply mains before
removing the guard.
●The appliance is not intended for use by persons(including
children) with reduced physical ,sensory or metal capabilities,or
lack of experience and knowledge,unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
●This appliance can be used by children aged from 8 years and
above and persons with reduced physical,sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazard involved.
3
●Children shall not play with the appliance.
●Cleaning and user maintenance shall not be made by children
without supervision.
Description of parts
1 Front Guard
2 Locking screw
3 Fan Blade
4 Rear Guard
5 Front Guard Nut (x1)
6 Telescopic Stand
7 Pivot Adjustment Screw
8 Tilt Adjustment Screw
9 Motor Housing
10 On/Off/Speed Control
11 Oscillating Control
12 Motor Spindle
13 Fan Blade Retaining
Screw (x1)
14 Guard Retaining Clips
15 Stand Base
16 Weight
17 Clamping Washer
18 L - Shaped Screw
4
Assemble Your Metal Stand Fan
Steps:
1. Attach the Telescopic Stand (6) to the Base (15) by placing the
Weight (16) on the underside of the base (15) and the clamping
washer (17) in the centre of the weight.Thread the L-Shaped
Screw (18) through the assembly and into the thread in the
Telescopic tand (6). Tighten firmly but do not overtighten.
2. Next attach the motor housing (9) to the top of the telescopic
stand (6).First remove all the screws, etc.(7, 8, 19 & 20) from the
motor housing bracket.
5
3. Place the Motor Housing on the top of the stand and thread the
Large Pivot Bolt (20) through the bracket and screw in the Small
Retaining Screw (8) and tighten (but do not over tighten).
4. Fit the Large Pivot Knob (7) onto the end of the Bolt (20) and
the Small Adjusting Knob (19).Hold the fan motor upright and
tighten the Large Pivot Knob (7) and the Small Adjusting Knob
(19).
OPERATING INSTRUCTIONS
1. Set the fan on a dry, level and sturdy surface.
2. Plug the fan into the mains.
3. Be sure the voltage of fan conformed to local power condition
before using it.
Oscillation,adjusting angle
1. Push down the oscillation knob to make the fan head oscillate,
and pull-up the oscillation knob to stop the fan head from
oscillating.
2. Loosen the adjusting angle knob, adjust the fan to the desired
angle, to secure tighten the adjusting angle knob.
6
ON/OFF,Speed Selection
Adjust the desired speed by oscillate the power switch:
0--- Stop Ⅰ--- Low Ⅱ--- Medium Ⅲ--- High
CLEANING AND MAINTENANCE
Your fan reauires little maintenance and contains no user serviceable parts.
Do not attempt to dismantle the Fan Motor body yourself. The fan is
permanently lubricated and will not require additional lubrication.
Important: Do not allow water to run into the interior of the fan , as this cause
an electric shock .DRY THE FAN THOROUGHLY with a dry cloth, checking
that the fan is completely dry before operating the fan.
Important Safety Instructions
When using electrical appliance, basic precautions should be followed to
reduce the risk of fire and personal injury.
●DO NOT connect the appliance to the mains voltage until
completely assembled and adjusted
●Before you connect the appliance,check if the voltage specified
on the appliance corresponds to the mains voltage in your home.
●To protect against electrical shock,do not immerse until plug or
cord in water or spray with liquids.
●Never put objects into the grille when the fan is connected to the
mains
●Unplug from outlet when not in use ,when moving fan from one
location to another,before putting on or taking off parts and before
cleaning
●It is not advisable to expose people(esp.babies and older people)
yo a continuous cold air stream for a long time.
●DO NOT use fan in very hot to humid environment,such as
bathroom.
●Make sure fan is on a stable surface when operation to avoid a
7
chance of overturning.
●DO NOT use fan near curtains,plant, windows treatments,etc
●DO NOT operate in the presence of explosive and /or flammable
fumes
●DO NOT place fan or any parts near an open flame,cooked or
other heating appliance.
●DO NOT operate any appliance with a damaged cord or
plug,after the appliance malfunctions or has been dropped or
damaged in any manner.
●DO NOT let allow the cord to overhang a table of workshop.
●To disconnect,grip plug and pull from wall outlet NEVER yank on
cord.
●Always use on a dry surface.
●This product is intended for household use only and not for
commercial or industrial use.
●Disconnect fan before cleaning.
●Never remove the inner pipe stopper or remover the set knob
which holds the pipe stopper in place.
●DO NOT let the cord come into contact with hot surfaces.
MADE IN CHINA
