Loading ...
Loading ...
Loading ...
16 17
TECHNICAL DATA
We reserve the right to alter these specifications.
This appliance conforms to AS 5263.
Table 2
features WHG639BD WHG959BD WHG635BCA WHG955BCA
Cooking zones 3 5 3 5
Wok Yes, dual Yes, dual Yes Yes
Ignition 230-240V 230-240V 230-240V 230-240V
Trivet Cast Cast Cast Cast
Hob material Ceramic glass Ceramic glass Ceramic glass Ceramic glass
Features Ignition through knob Ignition through knob Ignition through knob Ignition through knob
Flame safeguard Yes Yes Yes Yes
Colours Black Black Black Black
Gas types
NG, (LP conversion
kit supplied)
NG, (LP conversion
kit supplied)
NG, (LP conversion
kit supplied)
NG, (LP conversion
kit supplied)
cooktop dimensions (mm)
Width 595 900 595 900
Depth 530 530 530 530
Height
(from top of pan
support to bench)
58 58 58 58
Height
(from bench to
bottom)
54 54 54 54
cut out dimensions (mm)
Width 560 860 560 860
Depth 490 490 490 490
energy rating (NG) – MJ/h
Small burner 5.1 2X5.1 5.1 2X5.1
Medium burner NA 9 9 2X9
Large burner 12.1 12.1 NA NA
Wok burner 19 19 14.4 14.4
Total MJ/ h 36.2 50.3 28.5 42.6
1. The bench cutout should be made as per cutout
dimensions in Table 2 and Figure 5.
2. Adjacent walls, cupboards and protection for
combustible materials: Ensure that the appliance
is installed in accordance with AS/NZS 5601.1,
or AS/NZS 5601.2 with regard to clearances
to combustible surfaces and materials, and
clearances to rangehoods and exhaust fans.
To ensure clearances of 200mm from burners
to vertical combustible surfaces observe the
minimum distance requirements shown in Figure 5.
Clearances to combustible surfaces may be
reduced if combustible surfaces are protected
in accordance with AS/NZS 5601.1, or AS/NZS
5601.2.
3. For Ceramic Glass models a FOAM SEAL has
been provided and is to be applied along the
perimeter of the hob.
4. Fit the pull down clamps supplied to ensure that
the cooktop cannot move after installation.
5. The overhead clearance between the supporting
surface for the cooking vessels (top of the trivets)
of this gas cooking appliance and a range hood or
exhaust fan (overhead clearance) shall be not less
than 650 mm for a range hood, and not less than
750 mm for an exhaust fan.
6. A Rangehood or exhaust fan shall be installed in
accordance with the range hood or exhaust fan
manufacturer’s relevant instructions.
7. Where the range hood or exhaust fan
manufacturer’s relevant instructions specify a
greater clearance, then this greater clearance shall
apply.
8. Any other downward facing combustible surface
less than 650 mm above the supporting surface for
the cooking vessels shall be protected for the full
width and depth of the hob in accordance with AS/
NZS 5601.
9. Clearance to any overhead surface shall be not less
than 450 mm.
Note 1: Removable accessories such as a wok
trivet that sits upon a hob trivet are not taken into
account in determination of the supporting surface
for the cooking vessels.
Note 2: Minor elevations in trivets such as a wok
trivet formed into a trivet are not taken into account
in determination of the supporting surface for the
cooking vessels.
Note 3: The height of the top of the pan supports
(top of the trivets) with respect to the bench top
(built in) or supporting surface (elevated) or the
floor (freestanding) are detailed separately in these
instructions.
INSTALLATION PROCEDURE
WARNING!
Failure to fix the cooktop to the bench could result in
loosening of the gas connection through movement of the
cooktop and a gas leak may result.
Four clamps and screws are supplied with 3/4-burner
models and six clamps and screws are supplied with
5-burner models. Fit the clamps as shown in Figure 7.
When benchtops are less than 33mm in thickness, it may
be necessary to fit a spacer between the benchtop and
each clamp to ensure clamps can be tightened sufficiently.
Loading ...
Loading ...
Loading ...