AccuTemp Products, Inc. · 8415 North Clinton Park · Fort Wayne, IN 46825 ·800 210-5907 · accutemp.net
MP5004-1202
ELECTRIC GRIDDLE
INSTALLATION & OWNERS MANUAL
Serial Number:
Model:
Install Date:
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 1
TABLE OF CONTENTS
Instructions for Warranty Registration 2
Startup Form 3
Document History 4-5
Safety Warnings Denition 6
Safety Symbols Deniton 7
Specication Model EGF 8-9
Specication Model EGD 10
Introduction 11
Installation Model EGF 12-14
Installation Model EGD 15-21
Operation 22-23
Cleaning 24-26
Service and Troubleshooting 27-29
Parts - Commercial 30-34
Parts-Military 35-40
Model EGF Schematics 41-45
Model EGD Schematics 46-48
Warranty 49
This manual is for AccuSteam Griddles Starting with:
Model EGD Series S/N 7547
Model EGF Series S/N 7642
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 2
Before installing this appliance complete the following items:
Fill in the warranty registration card that was enclosed in the documentation packet that came with the 1.
appliance.
Complete the startup checklist on page 2 of this manual.2.
Mail, fax or email the warranty registration card and startup form to AccuTemp™.3.
If you have any questions please contact our technical service group. They are available 7 days a week from
7:00 am to 7:00 pm EST.
800 480-0415 Toll Free
260 469-3040 Ofce
260 469-3045 Fax
[email protected] email
www.accutemp.net web site
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 3
"
6+):165
,,8-99
1:?
":):-
'17
065-;4*-8
4)13
6,-3
"-81)3
)4-6."-8<1+-/-5+?
#-+051+1)5
-)9;8-,";773?$63:)/-0-+265-
$ $ $ $
0)915/0-+265-
"15/3- 0)9- #08-- 0)9-
";773?+68,19+655-+:-,:67867-8/86;5,
&-9 6
$-81.?)+:;)39;8.)+-:-47-8):;8-):)
:0-8469:):9-::15/6.
6#;9-15.-88-,:0-8464-:-89
$-81.1-,(((((((((
644-5:9
)++-7::019+0-+26..319:)9+6473-:-)5,)++;8):-
!-9:);8)5:)5)/-8
):-
6:-":)8:;7.6844;9:*-.133-,6;:+6473-:-)5,+688-+:3?:0-5-1:0-8.)>-,684)13-,:6:0-
++;#-47#-+051+)3"-8<1+--7)8:4-5:*-.68-7)?4-5:19199;-,
++;#-47 86,;+:95+
::5#-+051+)3"-8<1+--7:
68:0315:65 )828
68:%)?5-
065-)>
"-8<1+-6;89,)?9)=--2)4 @ 74
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 4
DOCUMENT HISTORY
Current revision: – Prior revision: None
Date: 8/4/05 Date: None
Change
Initial release.
_______________________________________________________________________
Current revision: A Prior revision: –
Date: 8/16/05 Date: 8/4/05
Change
Added pages 26, 28 – 30, and 34 – 36; Renumbered pages as necessary.
_______________________________________________________________________
Current revision: B Prior revision: A
Date: 10/7/05 Date: 8/16/05
Page Change
Added pages ii and 24 – 27; Modied pages 4 – 8 and 19 – 23; Renumbered pages as necessary.
_______________________________________________________________________
Current revision: C Prior revision: B
Date: 10/12/05 Date: 10/7/05
Page Change
Added page iii; Modied pages iv, 19 – 27; Renumbered page iv.
_______________________________________________________________________
Current revision: D Prior revision: C
Date: 11/10/05 Date: 10/12/05
Page Change
Deleted pages ii, iii, and 25; Added pages 18, 33 and 34; Modied pages 13, 14, 25 – 32, and 35 –
40; Rearranged sections and pages for clarity; Renumbered pages as necessary.
_______________________________________________________________________
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 5
DOCUMENT HISTORY (cont.)
Current revision: E Prior revision: D
Date: 12/29/05 Date: 11/10/05
Page Change
Added page ii; Modied pages 18, 19, 22 – 24, 33, and 34.
_______________________________________________________________________
Current revision: MP5004-0811 Prior revision: D
Date: 12/29/05 Date: 11/10/05
Page Change
Added page ii; Modied pages 18, 19, 22 – 24, 33, and 34.
Current revision: MP5004-1412 Prior revision: MP5004-0811
Date: 02/14/2012 Date: 11/10/05
Page Change
Numeric Page Numbers all pages
All Pages Modied for Engineering Changes
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 6
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTE
Advises reader of information or instructions vital to the operation or maintenance of the
equipment.
SAFETY WARNINGS
SYMBOL DEFINITIONS
Symbols are used to attract your attention to possible dangers. They are only effective
if the operator uses proper accident prevention measures. Some of the symbols are
boxed text, while other maybe just picture icons. Please give this information the
respect they deserve for safe operation.
WARNING TEXT BOXES
Below are denitions of the warning text boxes:
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 7
SAFETY WARNINGS (cont.)
SYMBOL ICONS
Below are denitions of symbol icons used in this manual:
ALERT – Noties the reader of an important message/warning, usually a safety related
message.
INFORMATION – Noties the reader of important information that may or may not be
safety-related.
EARTH GROUND
DANGEROUS VOLTAGE
CAUTION, HOT SURFACE
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 8
RIGHT SIDE VIEW
TOP VIEW
(2)
Power Cord
Provided
Grease Trough
(A)
4 1/2"
[114]
Control Panel
Grease Pan
(C)
(Cooking Depth)
17 5/8"
[448]
12 3/4" [323]
(Cooking Height)
(B)
(Cooking Width)
Feet Standard
(D)
Unit Depth
22 3/4" [578]
Bullet Feet Footprint
(E) 2 5/8”
[66]
Griddle Width
24”
36”
48”
Dim leg-to-leg
20”
32”
44”
RIGHT SIDE VIEW
EGF FLUSH MOUNT SERIES
8 1/4" [209]
(Cooking Height)
12 9/16"
[319]
AccuTemp Products, Inc.
Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)
Model # EGF****A2400-T1 EGF****B2400-T1 EGF****A3600-T1 EGF****B3600-T1 EGF****A4800-T1 EGF****B4800-T1
KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW
208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56
240/1 Amp Load 40 40 n/a n/a n/a n/a
240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28
440/3 Amp Load 17.1 17.1 25 25 25 25
480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87
Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]
Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]
Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]
Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]
Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]
Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.
Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.
NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P
NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P
A
CCU
-S
TEAM
™ G
RIDDLE
EG S
ERIES
Notes:
1.) Dimensions in brackets [ ] are metric.
2.) 5’ power cord wtih plug provided.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 9
AccuTemp Products, Inc.
Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)
Model # EGF****A2400-S2 EGF****B2400-S2 EGF****A3600-S2 EGF****B3600-S2 EGF****A4800-S2 EGF****B4800-S2
KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW
208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56
240/1 Amp Load 40 40 n/a n/a n/a n/a
240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28
440/3 Amp Load 17.5 17.5 25 25 25 25
480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87
Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]
Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]
Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]
Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]
Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]
Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.
Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.
NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P
NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P
A
CCU
-S
TEAM
™ G
RIDDLE
EG S
ERIES
Notes:
1.) Dimensions in brackets [ ] are metric.
2.) 5’ power cord wtih plug provided.
(D)
Unit Depth
(2)
Power Cord
Provided
Grease Chute
(A)
(B)
(Cooking Width)
(C)
(Cooking Surface Depth)
40 7/16"
[1028]
Control Panel
Grease Pan
27 7/8"
[709] 36 1/8"
[918]
(Cooking Height)
Stand With
Casters
Griddle Width
24”
36”
48”
Dim leg-to-leg
20”
32”
44” 22 3/4” [578]
Leg-to-Leg Footprint
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 10
35.50"
[902mm]
1.625 - 4.125"
[41 - 105mm]
6.50"
[165mm]
(A)
(B)
Cooking Surface Width
(C)
Cooking Surface
Depth
29.50"
[749mm]
8.87 - 11.0"
[225 - 279mm]
See Note 2
1.31"
[33]mm
1.5" [38mm]
Depth To Cooking Surface
.73 - 2.63"
[9 - 67mm]
See Note 2
0" - 1.0"
[0 - 25mm]
Accu-Steam Drop-In Griddle Specifications
(replace **** with voltage & phase, i.e. 2083)
Model #
EGD****B3600-00 EGD****B4800-00
KW Input 14.25 kW 14.25 kW
208/3 Amp Load 39.56 39.56
240/3 Amp Load 34.28 34.28
440/3 Amp Load 21 21
480/3 Amp Load 17.14 17.14
Unit Width (A) 36.5 [927] 49 [1245]
Unit Depth (D) 29.5 [749] 29.5 [749]
Cooking Surface Width (B) 34 [864] 46.5 [1181]
Cooking Surface Depth (C) 23.5 [597] 23.5 [597]
Effective Cooking Area 799 sq in
[20295 sq mm]
1093 sq in
[27762 sq mm]
Rough Opening Griddle 35.5 x 28.5
[902 x 724]
47.75 x 28.5
[1213 x 724]
Rough Opening Control
Panel
33.75 x 4.875
[857 x 124]
33.75 x 4.875
[857 x 124]
Grease Pan Capacity 1.5 gal. 1.5 gal.
NEMA Plug (208/240) 15-50P 15-50P
NEMA Plug (440/480) L16-30P L16-30P
A
CCU
-S
TEAM
™ G
RIDDLE
EG S
ERIES
Drop-In Griddle
Notes:
1.) Dimensions in brackets [ ] are metric.
2.) 5’ power cord wtih plug provided.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 11
THEORY OF OPERATION
INTRODUCTION
The ACCU-STEAM™ griddle is constructed and uses technology like no other griddle in the
world. The diagram below is a cross-sectional view of the griddle. The griddle cooking surface
is the top of a chamber in which we have produced a unique environment. Welded stainless steel
reinforcement studs connect the chamber top to the chamber bottom. The perimeter joints are
all robotically welded to produce a vessel that is airtight, which is veried using a helium mass
spectrometer. The chamber is lled half full with distilled water. The remaining air is removed
and the chamber is welded shut. At this point, the chamber becomes a hermetically sealed vessel,
never to be opened again. The griddle steam chamber requires no water or maintenance. A
thermowell for a temperature sensor to sense temperature and a thermowell for the overtemp
safety shutdown system are also welded into the griddle steam chamber.
At temperatures below 212°F (100°C), the chamber is actually in a vacuum, similar to that of a
canning jar. At temperatures above 212°F (100°C), the chamber operates under pressure. Located
between the water and the bottom of the cooking surface is the best heat transfer medium –
steam, the most effective way to transfer heat. The temperature sensor senses the temperature
of the steam and reports this data to the thermostat, which energizes the heating elements. This
system maintains the griddle cooking surface temperatures to within ± 5°F (2.7°C) over the
entire cooking surface and provides a near instant temperature recovery, even in the same spot on
the griddle, when turning food in place.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 12
ELECTRIC
TABLE TOP & STAND
MODEL EGF SERIES
INSTALLATION INSTRUCTIONS
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 13
INSTALLATION
TABLE TOP/STAND MODEL - EGF SERIES
LOCATION AND PLACEMENT
The AccuTemp ACCU-STEAM™ electric griddle has been designed to be placed on a
commercial kitchen counter-top, an AccuTemp griddle stand or directly onto any at, level
surface.
The operating temperature ranges from 200°- 400°F (93°- 204°C). Since these temperatures can
also be found on surfaces around the perimeter of the griddle, care should be given not to install
griddle next to or against, objects or surfaces with a low melting or ash point.
LEVELING
The griddle must be installed in a level condition. An out-of-level condition may cause uneven
temperatures and in server out of level condition damage to the griddle that may not be covered
by warranty. Use a spirit level resting on the griddle surface to ensure it is level front-to-back and
left-to-right.
Table Top
Install the (4) rubber foot tips provided with your griddle onto the four foot adjusters of each of
the griddle legs. This will keep the griddle from sliding on the counter-top under normal use.
Once the rubber foot tips have been installed, adjust the four foot adjusters up or down as needed
to level the griddle.
ACCUTEMP STAND
If on an AccuTemp™ stand with casters, ensure that the oor surface is level and place the
two locking casters to the “on” position and follow the leveling instructions to verify the the
appliance is level.
IN-FIELD MODIFICATIONS
This griddle has a totally unique design and is constructed unlike any other griddle on the market
today. Any modication may permanently damage the griddle.
Only a qualied service or electrician should complete the installation to ensure that all
eletrical and safety requirements are met and that all wiring is installed as per all National,
State and Local electrical codes.
WARNING
This appliance is heavy. For safe handling, the installer should obtain help as needed or
employ appropriate material handling equipment to remove the appliance from the skid
and move into the nal destination.
WARNING
Any in eld modications made without written authorization from AccuTemp™ will void
all warranties
NOTE
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 14
NEMA 6-50R NEMA 15-50R NEMA L16-30R
INSTALLATION
This appliance must be properly grounded, In accordance with all the National, State and
local electrical codes.
WARNING
ELECTRICAL SUPPLY
The ACCU-STEAM™ griddle has been designed, manufactured and tested to meet or exceed
the demanding standards of safety set forth by Underwriters Laboratories, Inc. To ensure that
this high level of safety is maintained in your installation, it is important that you read and
understand the following information before attempting to plug in your griddle.
ELECTRICAL REQUIREMENTS
Electrical requirements are listed on the data plate located on the right side of the unit, near the
front. All standard AccuTemp griddles are supplied with a 6ft (1.83m) cord and the appropriate
UL listed plug. Please note, that the plug is rated for 250VAC. This plug is commonly used for
both 208VAC and 240VAC installations. Make sure that the voltage at your supply receptacle
is within ± 10 % of the voltage listed on the griddle data plate. Connection to any other voltage
may cause damage to components in the griddle and damage of this type is not covered under
warranty.
GROUNDING INSTRUCTIONS
Grounding provides a path for electric current to reduce the risk of shock. This product is
equipped with a power cord having a grounding conductor and a grounding plug.
ELECTRICAL CONNECTIONS (MODEL EGF ONLY)
The receptacle requirements vary between models.
If you have purchased a 240 V single-phase model, you will need a NEMA 6-50R
receptacle. If you have purchased 208/240V a three-phase model, you will need a NEMA
15-50R receptacle and if you purchased a 440V/480V three-phase model you will need a
NEMA l16-30R receptacle
These receptacles are congured as shown below.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 15
MODEL EGD
INSTALLATION INSTRUCTIONS
This appliance is heavy. For safe handling, the installer should obtain help as needed or
employ appropriate material handling equipment to remove the appliance from the skid
and move into the nal destination.
WARNING
Any in eld modications made without written authorization from AccuTemp™ will void
all warranties
NOTE
The appliance must be installed in accordance with the following building codes:
USA: National Electrical Code, ANSI/NFPA-70, state and local codes, International
Plumbing Codes 2003, ICC or Uniform Plumbling Code 2003, IAMPO. Canada Electric
Code, CSA C22.2 and state and local codes.
WARNING
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 16
Fig. 1
Introduction
It is highly recommended that a survey of the kitchen site be conducted to determine the
requirements for the installation. Electrical supply, counter space as well as counter arrangement
are critical to the choice of Drop-In-Griddle options. The Drop-In-Griddle is available in many
options to accommodate size, control panel arrangements and supply voltage. The model data
label indicating the model number, phase, voltage, current, wattage and UL information is
located on the bottom cover of the unit.
Counter designs that have an “L” arrangement such that the shortest part of the “L” is to the left
may require a “Right Hand Control Panel” option. A counter design that has an “L” arrangement
such that the shortest part of the “L” is to the right may require a “Left Hand Control Panel”
option. See Figure 1 for views of these congurations.
INSTALLATION
MODEL EGD
This product is to be installed in stainless or non-combustible countertops only.
CAUTION
Installation must allow inspection and serviceability to the undeside of the appliance
NOTE
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 17
INSTALLATION (cont.)
MODEL EGD
ELECTRICAL SUPPLY
The ACCU-STEAM griddle has been designed, manufactured and tested to meet or
exceed the demanding standards of safety set forth by Underwriters Laboratories, Inc.
To ensure that this high level of safety is maintained in your installation, it is important
that you read and understand the following information before attempting install your
griddle.
ELECTRICAL REQUIREMENTS
Electrical requirements are listed on the data plate located on the Bottom of the Control
Box, near the front. The EGD Series griddles are supplied with a 5ft (1.52m) cord. Make
sure that the voltage at your supply is within ± 10 % of the voltage listed on the griddle
data plate. Connection to any other voltage may cause damage to components in the
griddle and damage of this type is not covered under warranty.
This appliance must be properly grounded, in accordance with all National, State and local
electrical codes.
WARNING
GROUNDING INSTRUCTIONS
Grounding provides a path for electric current to reduce the risk of shock. This product
is equipped with a power cord having a grounding conductor.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 18
GETTING STARTED
Please read and comprehend all instructions and manuals provided with each Drop-
In-Griddle. Read and understand all safety warnings and operator instructions for all
powered tools required to complete the installation of the Drop-In-Griddle. Disconnect
all power from house supply connection boxes at the appropriate fuse panel
and label the breakers “In service”.
This is to warn others that work is in process, preventing accidental electrocution.
TYPICAL TOOLS AND SUPPLIES REQUIREMENTS
• Putty knife
• Grease solvents
• Clean sponges or rags
• Latex gloves
• Caulking gun
• Approximately 3oz. NSF-approved aluminized silicone sealant
• Tape measure
• Carpenters square
• #2 Phillips screw driver
• Channel lock pliers
• ½ inch box/open wrench
• 3/8 inch nut driver
• 3/8 inch electric or cordless drill
• #25 drill bit
• 3/8 inch drill bit
• Saber saw with metal cutting blades
• Permanent marking pen, preferably a “Sharpie” ne point.
• 4 inch grinder. (If replacing an existing competitors griddle, it is recommend to use
a 4 inch grinder to clean off any welds, welded on brackets or framing attached to
the counter top.)
LIST OF PACKAGING REQUIREMENTS:
• (1) Owners/Installation Manual
• (1) Griddle Module
• (1) Control Panel Module
• (1) Cable Assembly
• (4) Grease Spout Extension
• (1) Grease Trough Assembly
• (1) Grease Tray Assembly
• (1) Grease Trough Hanger Bracket
• (1) Grease Trough Hanger
• (8) 10-24 x 3/8 inch Self-Tapping Truss Head Screw
• (6) 10-24 x ½ inch Phillips Round Head Machine Screw
• (2) 5/16-18 X ¾ inch Carriage Head Bolt
• (2) 5/16 inch Lock Washer
• (2) 5/16-18 Hex Nut
• (8) 1/4-20 Nyloc Nut
• (4) Retainer Bracket
INSTALLATION (cont.)
MODEL EGD
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 19
1. Inspect the griddle packaging to ensure there are no missing components.
2. Complete the appropriate power disconnection procedures for existing equipment
or local power junction boxes.
3. Clean surfaces with grease solvents and dry off with clean rags or sponges.
4. Determine the location and orientation for the griddle and control panel modules.
Mark the centerline on the countertop for the griddle module, using a Carpenter’s
square. See Figure 2 for the countertop and control panel layouts. Continue the
centerline to the control panel module mounting surface. Accurate centerline
alignment of the countertop and control panel modules is critical to ensure the
correct alignment of the grease trough assembly to the griddle module.
Fig. 2
INSTALLATION DROP-IN GRIDDLE (cont.)
MODEL EGD
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 20
INSTALLATION PROCEDURE
5. The dimensional relationship between the griddle module mounting ange and
the control panel module is shown in Figure 3. The griddle module mounting
ange overlaps the countertop cutout by 0.50 inches on all four sides. Mark the
griddle module cutout on the countertop such that the front edge of the griddle
module is 0.73 inches – 2.63 inches from the control panel module mounting
surface, as shown in Figure 3. Mark the control panel module cutout on the
control panel module mounting surface, as shown in Figure 2.
6. Cut out the griddle and control panel module openings. Straighten out any dings or bent
edges in both cutouts to ensure adequate sealing between the new griddle and the counter
top surface and between the control panel and the front surface of the counter.
7. Drill the mounting holes in the face of the counter using a #25 drill bit. Drill the rst set
of holes and locate the remaining holes using the control panel as a template.
8. Use a lifting device, if possible, to raise the griddle module above the counter and position
over cutout in countertop. Lower the griddle module carefully into the cutout. Install the
retainer clamps to the griddle module, using the ¼-20 nylock nuts (see drawing AT2A-
3044, sheet 6).
9. Install the control panel onto the counter face using #10-24 x 3/8 inch self-tapping screws.
Also, at this time, install the thermostat knob guard, if necessary, by lining up the holes on
the guard to the holes on the control panel directly above and below the thermostat.
INSTALLATION DROP-IN GRIDDLE (cont.)
MODEL EGD
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 21
10. Install the grease trough hanger brackets onto the bottom side of the griddle using (2)
#10-24 X ½ inch Phillips round head machine screws and (2) 5/16-18 X ¾ inch carriage
head bolts with (2) 5/16 inch lock washers and (2) 5/16-18 nuts (see drawing AT2A-3044,
sheet 6). Leave the carriage bolts loose for adjustment of the grease trough.
11. Install the grease trough using (4) #10-24 X ½ inch Phillips round head machine screws
through the front panel opening and through the hanger bracket assembly, installed in step
10.
12. Adjust the hanger bracket height so that the grease trough is setting level front-to-back
and tighten the 5/16-18 nuts.
13. Install the appropriate size grease spout extension onto the griddle grease spout, that
ensures the bottom of the grease spout extension is ush to the inside surface of the
grease trough assembly (see drawing AT2A-3044, sheet 6).
14. Use the caulking gun to lay a 1/8” minimum diameter bead of the aluminized silicone
sealant around the griddle module mounting ange onto the counter top. Use a gloved
nger to wipe the sealant into a llet shape.
15. Install the interconnect cable between the control panel module and the control box,
mounted on the bottom side of the griddle (see drawing AT2A-3044, sheet 6).
16. Set the on/off switch to the off position and set the temperature control knob to the lowest
setting.
17. Install the power cord into an appropriate sized electrical connection box with an
appropriate sized cord grip or cable strain relief. Complete the nal connections,
testing the house supply wire rst to ensure it is not live.
18. Turn on power to the griddle at the fuse panel.
19.Turn the griddle on and set the temperature control knob to a desired setting. Wait
a minimum of 20 minutes. Then use a suitable temperature-measuring device to check
the griddle surface temperature. The surface temperature should be within 5 – 7 °F of the
temperature control knob setting. If it is not, go to the calibration section and follow the
calibration procedures.
20.This completes the drop-in griddle installation.
INSTALLATION DROP-IN GRIDDLE (cont.)
MODEL EGD
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 22
OPERATION
MODEL EGD & EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 23
SEASONING
It is recommended that you clean your ACCU-STEAM™ griddle thoroughly before turning your
unit on. To clean the griddle surface, just simply wash the cooking surface down with a solution
of mild soap and water, and then rinse thoroughly with clean water.
Once the cooking surface has been cleaned, set the thermostat to 200°F (93°C), turn the griddle
power switch to the “On” position and allow the griddle cooking surface to heat for 10 minutes.
Using a high temperature oil, such as Pan and Grill Shortening™, Whirl™ or equivalent,
pour enough to cover the entire griddle surface. Do not use standard vegetable oil to season
the griddle cooking surface. It may cause food to stick and result in improperly cooked food.
Work this seasoning oil into the griddle surface with a regular heavy-duty scrub pad for about 5
minutes, making sure that you scrub the seasoning oil over the entire griddle-cooking surface.
After the entire griddle surface has been scrubbed with seasoning oil for 5 minutes, simply wipe
or squeegee off excess oil from griddle surface. Your griddle is now ready to use!
If you use chemicals to clean your griddle periodically or on a schedule, you may need to
repeat this process after the use of chemicals.
PREHEATING
Turn On switch to the “On” position and set the thermostat to the desired temperature. The
griddle will increase its surface temperature at an average rate of 15° F (8°C) per minute. It
takes approximately 22 minutes to raise the griddle from room temperature to its maximum
temperature of 400° F (204°C). The griddle will be preheated when the “Heat” light starts to
cycle on and off. Please use caution as temperatures on and around the griddle cooking
surface could cause severe burns.
COOKING
Begin cooking only after the griddle has been preheated to the desired temperature. Please note
these facts:
• You can cook all the way to the edges of the griddle surface because the temperature
does not very across the entire cooking surface.
• You can turn the product to the same spot because the griddle has near instant heat
recovery.
• It will always cook the same, regardless of product load or surface coverage.
Accurate Cooking Temperatures
Because of the inaccurate surface temperatures and long recovery times common with other
griddles. It is doubtful you were cooking at the set temperature or the temperature you wanted.
Adjust the temperature on your ACCU-STEAM™ griddle and it will not change or vary by the
location on the griddle surface. There are no hot or cold zones.
Heat Lamp
It is normal for the heat light to cycle on and off. This light indicates when the heaters
are energized. You will soon notice how little they are energized to maintain perfect surface
temperatures on your griddle.
OPERATION
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 24
Grease Pan
Use caution when emptying the grease pan. The contents in this pan could cause severe burns.
The pan should be checked periodically and emptied as necessary to prevent an overow or
dangerous condition.
OPERATION (cont.)
Checking Temperatures
Due to the design of the ACCU-STEAM™ a weighted temperature probe and digital temperature must be used
cooking surface temperatures. Infrared or mechanical temperature measuring devices will not work properly
and may give false readings.
Weighted Temperature Probe Digital Temperature Reading Device
0415 • Fax: 260 493
Temperatures according to the following chart.
7. Temperatures Shall Be Within ±5º Of Each Other Across The Entire Surface.
Nine Point Chart
Horizontal
Position Vertical Temp Vertical Temp Vertical Temp
Rear Left Center Right
Center Left Center Right
Front Left Center Right
LF RFCF
LC RCCC
LR RRCR
The grease can contents could cause severe burns. Slowly remove the grease can from the
griddle to avoid spilling the contents
WARNING
Never leave a chorine sanitizer in contact with stainless steel longer than 10 minutes. Any
longer and corrison could occur.
NOTE
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 25
CLEANING
MODEL EGD & EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 26
DAILY CLEANING
Cleaning during the work shift can be performed with a sharp scraper. When heavy cleaning at
the end of a shift or periodically as needed, the following is recommended:
• Turn the griddle off and allow it to cool to between 220°F and 240°F (104°F and
116°C). Use water, ice and/or griddle cleaner as needed. For example, the 3M Scotch-
Brite™ Quick Clean Griddle System provides the Scotch-Brite polishing pads, quick
clean liquid, pad holder and squeegee. Clean-up is very easy using these tools with the
quick clean liquid, water, ice or combinations of these liquids.
Seasoning the griddle after the daily cleaning is recommended.•
CAUTION
If the cooking surface of the appliance has standing grease and the griddle is at a high
temperature using water or ice can cause the grease to splatter and cause skin burns.
NOTE
Do not use a appliance stome or brick to clean griddle cooking surface. Only use a fabric
scrub pad.
NOTE
Do not use a water-jet to clean the griddle as it can harn the electronic components in the
appliance.
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 27
SERVICE & TROUBLESHOOTING
MODEL EGD & EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 28
BASIC TROUBLESHOOTING
Griddle will not turn on
• Make sure the griddle is plugged in and the “On/Off” switch is in the On position.
• Check for a facility circuit breaker (or fuse) supplying the unit
Heat light will not come on
• Make sure the griddle is not hotter than the temperature you have it set for. If you
have turned down the temperature of the griddle, the heat light will not come on again
until the cooking surface drops below the temperature you have set.
• See if the heat light is coming on intermittently. While operating in a normal
condition, the heat light cycles on and off periodically when at temperature.
Uneven or inaccurate surface temperatures
Verify griddle is level front to back and side to side.•
Verify the surface temperature with an accurate surface probe thermometer. •
Use of an infrared thermometer will not give an accurate reading of the griddle •
surface temperatures.
Unit will not turn off
• This system, which is extremely rare, indicates a serious control malfunction.
• Turn off the griddle’s electrical supply at the source.
SERVICE AND TROUBLESHOOTING
Use of any replacement parts other than those supplied by AccuTemp ™ can cause injury
to the operator or damage the appliance and voids all warranties
WARNING
NOTE
Service should be completed by Accutemp™ authorized service groups. Service completed
by unauthorized groups will void all factory warranties.
There are no user-serviceable parts. To prevent electrical shock do not open the access panel
covers.
WARNING
Any in-eld modication that bypass the built in safety features of this appliance will result
in death or serious injury.
DANGER
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 29
WARRANTY PROCEDURE
An AccuTemp Products, Inc. Technical Service Technician is available:
Monday thru Sunday, 7:00am to 7:00pm EST.
SERVICE AND TROUBLESHOOTING (cont.)
Contact the AccuTemp™ Technical Service group for all warranty service requests.1.
Be prepared to supply the serial number, address, location phone and contact for the location.2.
Be prepared to complete a few simple tasks to help evaluate the problem.3.
If the problem requires service at the location the AccuTemp™ Technical Service group will 4.
dispatch the nearest authorized service agent.
NOTE
Service should be completed by Accutemp™ authorized service groups. Service completed
by unauthorized groups will void all factory warranties.
NOTE
AccuTemp™ Technical Service group must be contacted for all warranty service requests
or the warranty claim my be denied.
800 480-0415 Toll Free
260 469-3040 Ofce
260 469-3045 Fax
[email protected] email
www.accutemp.net web site
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 30
PARTS
COMMERCIAL
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 31
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT0E-1800-5 INDICATOR LAMP RED 250V
2 AT0E-1800-4 INDICATOR LAMP GREEN 250V
3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4 AT0F-1046-31030 SCREW,#8-32 X 3/8 PHLP TRUSS HEAD
5 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
6 AT0F-3371-1 NUT ROTARY SHAFT SEAL
7 AT0E-3189-1 ASSY, EG EXTERNAL THERMOSTAT
8 AT2G-1026-1 GASKET, CONTROL PANEL EG
9 AT0E-2559-7 THERMOSTAT
10 AT0E-3339-1 MOUNTING LATCH
11 AT0E-3338-1 CONTACT BLOCK
12 AT0A-2876-1 MDR WITH TERMINALS
13 AT0F-2777-31030 SCREW #8 TYPE AB X 3/8 TRUSS HD
14 AT2M-1559-1 COVER
15 AT2A-2916-1 HIGH LIMIT OVERTEMP ASSEMBLY
16 AT0E-2885-3 SENSOR, REPLACEABLE
17 AT0F-2755-41070 SCREW, #10-24UNCX7/8 PHILIPS ROUND HEAD MACHINE
18 AT0E-1134-4 4 POSITION TERMINAL BLOCK
19 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW
20 AT0F-2691-41002 NUT, 10-24 NYLOC
21 AT0F-2662-3 TRANSFORMER 440V,480V
1
3
2
45678
9
10 11
13
15
14
12
16
17 19
20
18
21
24
22
23
26
25
28
27
29 30
33 32
31
34
COMMERCIAL MODEL EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 32
ITEM NUMBER PART NUMBER DESCRIPTION
22 AT2A-3032-3 4” LEG ASSEMBLY, FLANGE, OPTIONAL
22.1 AT2A-3032-1 4” LEG ASSEMBLY, STANDARD (NOT SHOWN)
22.2 AT2A-3032-2 8” LEG ASSEMBLY, OPTIONAL (NOT SHOWN)
23 AT0F-2875-51062 SCREW, 1/4-20UNC x3/4 HEX HEAD MACHINE
24 AT0E-1587-1 3 POLE CONTACTOR
25 AT0F-2755-41040 SCREW, #10-24UNC X1/2 PHILPS ROUND HEAD MACHINE
26 AT0F-1046-31030 SCREW, #8-32 X 3/8 PHLP TRUSS HEAD
27 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL
28 AT2G-1022 GASKET, EGF ACCESS POWER TERMINAL
29 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF
30 AT0A-2788-14 POWER CABLE ASSEMBLY - 440V
30.1 AT0A-2788-17 POWER CABLE ASSEMBLY - 208V/3 PHASE (NOT SHOWN)
30.2 AT0A-2788-18 POWER CABLE ASSEMBLY - 240V/SINGLE PHASE (NOT SHOWN)
30.3 AT0A-2788-19 POWER CABLE ASSEMBLY - 480V/3 PHASE
31 AT2M-3183-1 BAR, 24” GRIDDLE GRAB
31.1 AT2M-3183-2 BAR, 36” GRIDDLE GRAB ( NOT SHOWN)
31.2 AT2M-3183-3 BAR, 48” GRIDDLE GRAB (NOT SHOWN)
32 AT2H-3184-1 END BRKTS, GRIDDLE GRAB BAR
33 AT0F-2778-71001 NUT, 3/8-16UNC-2B 11 HEXMACHINE SCREW
COMMERCIAL MODEL EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 33
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2A-3243-1 ASSY, EG CONTROL PANEL WELDMENT
3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4 AT0E-3339-1 MOUNTING LATCH
5 AT0E-3338-1 CONTACT BLOCK
6 AT0E-2559-7 TEMPERATURE CONTROLLER
7 AT0E-1455-2 KNOB FOR D SHAFT
8 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V
9 AT0E-1800-5 INDICATOR LAMP RED NEON 250V
10 AT0E-2715-3 OVERLAY CONTROL PANEL
13 AT2A-3283-1 ASSY, WIRE HARNESS
14 AT2G-1026 GASKET CONTROL PANEL, EG
16 AT0F-3371-1 NUT, ROTARY SHAFT SEAL
AT2A-3189 - ASSEMBLY, ELECTRIC CONTROL PANEL
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 34
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2M-2861-1 WIRE ROD, OVERTEMP
2 AT2M-2860-1 SOLDER WASHER OVERTEMP
3 AT0F-1367-1 WASHER, TYPE A
4 AT2H-1365-1 COMPRESSION SPRING
5 AT2M-1558-1 BRACKET SWITCH LEFT HAND
6 AT2H-1640-1 EXTENSION SPRING
7 AT2E-1639-1 MICROSWITCH
8 AT0F-2691-21002 NUT, #6-32 NYLOC
9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED
10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILI ROUND HEAD
MACHINE
11 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
AT2A-2916-1- HIGH LIMIT OVERTEMP ASSEMBLY
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 35
PARTS
MILITARY
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 36
ITEM NUMBER PART NUMBER DESCRIPTION
1.1.2 AT2A-2185 WELD ASSY, CHAMBER
2 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL
3 AT2G-1022 GASKET PANEL ACCESS POWER TERMINAL, EG
4 AT2A-3189-1 ASSY, EXT THERM CONTROL PANEL
4.1 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4.2 AT0H-1455-2 KNOB FOR D SHAFT
4.3 AT0E-2559-7 TEMPERTURE CONTROLLER
4.4 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V
4.5 AT0E-1800-5 INDICATOR LAMP RED NEON 250V
4.6 AT0E-3338-1 CONTACT BLOCK
4.7 AT0E-3339-1 MOUNTING LATCH
4.8 AT0F-3371-1 NUT, ROTARY SEAL
5 AT0G-1026-1 GASKET, CONTROL PANEL, EG
6 AT0E-1587-1 3 POLE CONTACTOR
7 AT0E-2662-3 TRANSFORMER
8 AT2A--2916-1 HIGH LIMIT OVERTEMP ASSEMBLY
9 AT2M-1559-1 COVER
10 AT0E-1134-4 4 POSITION TERMINAL BLOCK
11 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW
16 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF
17 AT0A-2788-14 POWER CABLE ASSEMBLY
17.2 AT2E-2567-6 CABLE 6 AWG 4 COND
18 AT2A-2529-2 GREASE TROUGH ASSY
MODELS
EGF4403B3605-T3
EGF4803B3605-T3
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 37
ITEM NUMBER PART NUMBER DESCRIPTION
19 AT2A-2552-2 ASSY, BAFFLED LOCKING GREASE TRAY
19.1 AT0F-1046-41040 SCREW, #10-24X 1/2 PHLP TRUSS HEAD
19.2 AT2M-2551-2 GREASE TRAY FACE PLATE
19.3 AT2M-3008-1 LEVER, GREASE PAN
19.4 AT0F-3012-1 SPACER, ROUND
19.5 AT0F-1052-43010 WASHER, # 10 TYPE B CUSTOM
19.6 AT0F-1922-40000 WASHER, #10 SS HELICAL SPRING LOCK
19.9 AT0F-2632-41001 NUT, A0-24 ACORN
20 AT2A-3032-3 3” LEG ASSEMBLY
21 AT0F-2755-41050 SCREW, #10-24UNC X 5/8 PHILIPS ROUND HEAD MACHINE
22 AT0-1046-31030 SCREW, #8-32 X 3/8 TYPE AB PHILIPS TRUSS HEAD
23 AT0F-2755-41070 SCREW, #10-24UNC X 7/8 PHILIPS ROUND HEAD MACHINE
24 AT0F-2777-31030 SCREW, #8-32 X 3/8 TYPE AB TRUSS HEAD
25 AT0F-2691-41002 NUT, #10-24 NYLOC
26 AT0F-2875-51062 SCREW, 1/4-20UNC X 3/4 HEX HEAD MACHINE
29 AT0F-2778-71001 NUT, 3/8 UNC SS
30 AT0F-2875-71080 SCREW, 3/8-16UNC X 1 HEX HEAD MACHINE
31 AT0H-3184-1 END BRKTS, GRIDDLE GRAB BAR
32 AT2M-3183-2 36” GRIDDLE GRAB
33 AT0F-2755-41040 SCREW, #10-24UNC X 1/2 PHILIPS ROUND HEAD MACHINE
35 AT0E-2885-3 SENSOR REPLACEABLE
56 AT2A-3227-2 ASSY, 36” GRIDDLE FRONT 36” SKIRT
57 AT2M-3464-5 SKIRT, FRONT 36” MARITIME
56.2 AT0F-2668-1 NUTSERT, 10-24 HEX
MODELS
EGF4403B3605-T3
EGF4803B3605-T3
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 38
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2M-3103-1 CHASSIS, RELAY ENCLOSURE
2 AT2M-3104-1 COVER RELAY ENCLOSURE
3 AT0H-2576-1 GROMMET, 7/8 NYLON
4 AT0E-2206-3 HEAT SINK, 3.43” LONG
5 AT0E-2296-1 PAD, SSR HEAT SINK
6 AT0E-2059-3 RELAY SOLID STATE
7 AT0A-3111-1 CONTROL INPUT HARNESS
8 AT0A-3111-2 CONTROL INPUT HARNESS
9 AT0A-3112-4 ASSY, HARNESS
10 AT0A-3112-3 ASY, HARNESS
11 AT0A-3112-2 ASSY, HARNESS
12 AT0A-3112-1 ASSY HARNESS
13 AT0F-2755-31040 SCREW, #8-32UNC X 1/2 PHILIPS ROUND HEAD
MACHINE
14 ATOF-2666-40000 WASHER, #8 INTERNAL TOOTH LOCK
15 AT0F-2755-31040 SCREW, #10-24UNC X 1/2 PHILIPS ROUND
HEAD MACHINE
16 AT0F-2666-40000 WASHER INTERNAL TOOTH LOCK
17 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
24 AT0F-2668-1 NUTSERT, #10-24 HEX
MODELS
EGF4403B3605-T3
EGF4803B3605-T3
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 39
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2A-3243-1 ASSY, EG CONTROL PANEL WELDMENT
3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4 AT0E-3339-1 MOUNTING LATCH
5 AT0E-3338-1 CONTACT BLOCK
6 AT0E-2559-7 TEMPERATURE CONTROLLER
7 AT0E-1455-2 KNOB FOR D SHAFT
8 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V
9 AT0E-1800-5 INDICATOR LAMP RED NEON 250V
10 AT0E-2715-3 OVERLAY CONTROL PANEL
13 AT2A-3283-1 ASSY, WIRE HARNESS
14 AT2G-1026 GASKET CONTROL PANEL, EG
16 AT0F-3371-1 NUT, ROTARY SHAFT SEAL
AT2A-3189 - ASSEMBLY, ELECTRIC CONTROL PANEL
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 40
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2M-2861-1 WIRE ROD, OVERTEMP
2 AT2M-2860-1 SOLDER WASHER OVERTEMP
3 AT0F-1367-1 WASHER, TYPE A
4 AT2H-1365-1 COMPRESSION SPRING
5 AT2M-1558-1 BRACKET SWITCH LEFT HAND
6 AT2H-1640-1 EXTENSION SPRING
7 AT2E-1639-1 MICROSWITCH
8 AT0F-2691-21002 NUT, #6-32 NYLOC
9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED
10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILIOS ROUND HEAD MACHINE
11 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
AT2A-2916-1- HIGH LIMIT OVERTEMP ASSEMBLY
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 41
ACCUSTEAM ELECTRIC SERIES
SCHEMATICS
MODEL EGF
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 42
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGF
208/240V 3 PHASE
AT2T-3640-1 REV A
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 43
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGF
240V SINGLE PHASE
AT2T-3640-2 REV A
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 44
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGF
380V-435V 5 WIRE
AT2T-3640-3 REV A
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 45
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGF
440V/480V 3-PHASE
AT2T-3640-4 REV A
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 46
ACCUSTEAM ELECTRIC SERIES
SCHEMATICS
MODEL EGD
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 47
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGD
440V/480V 3-PHASE WYE
AT2T-2713-7 REV L
AT2T-2713-8440/480V WYE SSR HEATER CONFIGURATION DIGITAL CONTROLLER OR THERMOSTAT
ORNYEL
REDWHTBLKGRN
WHTWHTBLK
BLUBLU
BLKFINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY480V440V240V208VCOM
AT0E-2662-5
24VF1F23AG .5AAT0E-2731-1BLKWHTREDZR2WHTREDBLKZR1REDAT2E-1587-4AT0E-2736-5AT0E-2736-8RLY 1ZR4L3L2L1WHTSSR 1 SSR 2
1 P3 21 J3 2
SW2O.T. SWN.O.N.C.
1 P4 21 J4 2
REDREDBLKBLKAT2A-2916-2AT0A-2758-11 P5 21 J5 2WHT1 2 3 4 5 6 7J21 2 3 4 5 6 7P1P21 2 3 4 5 6 7
WHTREDORN
REDBLKWHTORNGRNBLUWHT/BLKJ11 2 3 4 5 6 7
BLKWHTGRNBLUE+BLUE-
CONTROL PANEL
BLK
CONTACTOR ENCLOSURE
AT2A-2764-1AT2A-2760-5AT0A-2761-1
YELORNRED
ON/OFF
BLK
1 2J21 2 3 4J71 2J3+24VGNDSENSOR INPUTPOWER INPUTYELREDJ11 2 3 4 5 6 7ON/OFFSW1PWRLT1HEATLT2BLKREDWHTORN
YEL
CONTROL PANEL
AT2E-1755AT0E-1800-1AT0E-1800-2AT2A-2762-2
BLUBLU
PRTDREDREDWHT
ORN
DIGITAL CONTROLER
1 3 5 6 8 9 L1 L2 OUTPUT PRTD PRTD TYPE CONTROLLER CAL OFFSET ADJ
t
o
ANALOG CONTROLER
BLKWHTREDR1R3R25163L3L1L2N42
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 48
ACCUSTEAM ELECTRIC SERIES SCHEMATIC
MODEL EGD
208/240V 3 PHASE
AT2T-2713-8 REV L
AT2T-2713-7208/240V DELTA SSR HEATER CONFIGURATION DIGITAL CONTROLLER OR THERMOSTAT
L
ORNYEL
REDWHTBLKGRN
WHTWHTBLK
BLUBLU
BLKFINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY480V440V240V208VCOM
AT0E-2662-5
24VF1F23AG .5AAT0E-2731-141263L3L1L25BLKWHTREDNR1R3R2ZR2WHTREDBLKZR1REDAT2E-1587-4AT0E-2736-5AT0E-2736-8RLY 1ZR4L3L2L1WHTSSR 1 SSR 2
1 P3 21 J3 2
SW2O.T. SWN.O.N.C.
1 P4 21 J4 2
REDREDBLKBLKAT2A-2916-2AT0A-2758-11 P5 21 J5 2WHT1 2 3 4 5 6 7J21 2 3 4 5 6 7P1P21 2 3 4 5 6 7
WHTREDORN
REDBLKWHTORNGRNBLUWHT/BLKJ11 2 3 4 5 6 7
BLKWHTGRNBLUE+BLUE-
CONTROL PANEL
BLK
CONTACTOR ENCLOSURE
AT2A-2764-1AT2A-2760-5AT0A-2761-1
YELORNRED
ON/OFF
BLK
1 2J21 2 3 4J71 2J3+24VGNDSENSOR INPUTPOWER INPUTYELREDJ11 2 3 4 5 6 7ON/OFFSW1PWRLT1HEATLT2BLKREDWHTORN
YEL
CONTROL PANEL
AT2E-1755AT0E-1800-1AT0E-1800-2AT2A-2762-2
BLUBLU
PRTDREDREDWHT
ORN
DIGITAL CONTROLER
1 3 5 6 8 9 L1 L2 OUTPUT PRTD PRTD TYPE CONTROLLER CAL OFFSET ADJ
t
o
ANALOG CONTROLER
Accu-Steam™ Installation and Owners Manial
MP5004-1202 PAGE 49
LIMITED WARRANTY
One Year - Parts & Labor - U.S. & Canada Only
AccuTemp Products, Inc. (AccuTemp) warrants that your AccuTemp equipment will be free of
defects in material and workmanship under normal use for a period of twelve (12) months from
installation or fifteen (15) months from date of shipment from AccuTemp, whichever date first
occurs (the Warranty Period). Registration of AccuTemp equipment is required at the time of
installation. Damage to AccuTemp equipment that occurs during shipment must be reported to the
carrier, and is not covered under this warranty. The reporting of any damage during shipment is the
sole responsibility of the commercial purchaser/user of such AccuTemp equipment.
AccuTemp provides an active service department, which should be contacted and advised of
service issues, regardless of the warranty period. During the warranty period, AccuTemp agrees
to repair or replace, at its option, F.O.B. factory, any part which proves to be defective due to
defects in material or workmanship, provided the equipment has not been altered in any way and
has been properly installed, maintained, and operated in accordance with the instructions in the
AccuTemp Owners Manual. During the warranty period, AccuTemp also agrees to pay for any
factory authorized equipment service agency (within the continental United States and Canada)
for reasonable labor required to repair or replace, at our option, F.O.B. factory, any part which
proves to be defective due to defects in materials or workmanship, provided the service agency has
received advance approval from AccuTemp factory service to perform the repair or replacement.
This warranty includes travel time not to exceed two hours and mileage not to exceed 50 miles
fittings or external electrical connections, minor adjustments, maintenance, gaskets or cleaning.
AccuTemp will not reimburse the expense of labor required to replace parts after the expiration of
the warranty period.
Proper installation is the responsibility of the dealer, owner-user, or installing contractor and is
not covered by this warranty. Improper installation can affect your warranty. Installation is the
responsibility of the Dealer, Owner/User or the Installation Contractor. See the Installation section
of the Owners Manual. While AccuTemp products are built to comply with applicable standards for
manufacturers, including Underwriters Laboratories (UL) and Underwriters Laboratories Sanitation
requirements, it is the responsibility of the owner and the installer to comply with any applicable local
codes that may exist.
AccuTemp makes no other warranties or guarantees, whether expressed or implied, including any
warranties of performance, merchantability, or fitness for any particular purpose. AccuTemp liability
on any claim of any kind, including negligence, with respect to the goods and services covered
hereunder, shall in no case exceed the price of the goods and services, or parts thereof, which gives rise
to the claim. In no event shall AccuTemp be liable for special, incidental, or consequential damages,
or damages in the nature of penalties.
This constitutes the entire warranty, which supersedes and excludes all other warranties, whether
written, oral, or implied.
WARRANTY
(100 miles round trip), but does not include post start-up assistance or training, tightening of loose
