Loading ...
Loading ...
Loading ...
English
9
1. To select speed 1 (high torque setting), turn the tool off
and permit it to stop. Slide the gear shifter
4
forward
(towards the chuck).
2. To select speed 2 (low torque setting), turn the tool off
and permit it to stop. Slide the gear shifter back (away
from the chuck).
nOTE: Do not change gears when the tool is running.
Always allow the drill to come to a complete stop before
changing gears. If you are having trouble changing
gears, make sure that the dual range gear shifter is either
completely pushed forward or completely pushedback.
Worklight (Fig. D)
The worklight
5
and its switch
12
are located on the foot
of the tool. The worklight is activated when the trigger
switch is depressed. The low
13
, medium
14
and spotlight
15
modes can be changed by moving the switch on the
foot of the tool. If the trigger switch remains depressed, the
worklight will remain on in allmodes.
When on low
13
and medium
14
settings, the beam will
automatically turn off 20 seconds after the trigger switch
isreleased.
Fig. D
5
15
13
14
12
Spotlight Mode
The high setting is the spotlight mode
15
. The spotlight
will run for 20 minutes after the trigger switch is released.
Two minutes before the spotlight will shut off, it will flash
twice and then dim. To avoid the spotlight shutting off,
lightly tap the triggerswitch.
WARNING: While using the worklight in medium
or spotlight mode, do not stare at the light or
place the drill in a position which may cause
anyone to stare into the light. Serious eye injury
couldresult.
CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause
a tripping or fallinghazard.
CAUTION: Remove all accessories from the chuck
before using the drill as a spotlight. Personal injury or
property damage couldresult.
Low Battery Warning
When in spotlight mode and the battery is nearing
complete discharge, the spotlight will flash twice and then
dim. After two minutes, the battery will be completely
discharged and the drill will immediately shut down. At this
point, replace with a freshbattery.
WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrantsit.
Keyless Single Sleeve Chuck (Fig. E–G)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changingacces sories.
WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personalinjury.
Your tool features a keyless chuck
6
with one rotating
sleeve for one-handed operation of the chuck. To insert a
drill bit or other accessory, follow thesesteps.
1. Turn tool off and disconnect tool from powersource.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desiredaccessory.
3. Insert the accessory about 3/4" (19 mm) into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with onehand.
Fig. F Fig. G
Fig. E
6
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximumtightness.
To release the accessory, repeat steps 1 and 2above.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.
Loading ...
Loading ...
Loading ...