Loading ...
NEW 9/22 2 T40733_T40735ES
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fi re, electrical shock and injury to persons:
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these devices may overheat and
cause a fi re hazard.
• DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fi re hazard.
• ALWAYS place the Fan on a stable, fl at, level surface while in operation to prevent the Fan from overturning.
• NEVER insert or allow fi ngers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
• DO NOT block, cover or obstruct air fl ow to or from the Fan while in operation.
• DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may create a shock hazard.
• DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Ar-
range cord away from traffi c area and where it will not be tripped over.
• NEVER use a single extension cord to operate more than one Fan or other electrical device.
• DO NOT use this Fan if it has been damaged or is not functioning properly.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural facilities including
areas where livestock, poultry or other animals are confi ned. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local
codes or standards relating to electrical requirements for agricultural buildings.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous locations. Please refer
to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for hazardous locations.
Lasko Products, LLC
820 Lincoln Avenue
West Chester, PA
19380
www.lasko.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes and modifi cations made to the
equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.”
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOLLOW THESE
IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this Fan to ventilate areas where fl ammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes,
fl oor refi nishing products or solvents. ALWAYS read and follow all warnings and instructions on the containers for these products!
ALWAYS be sure the plug fi ts tightly into the outlet. When plugs fi t loosely into outlets, they may slip partially out of the outlet and create a poor
connection. This may cause outlets to overheat and create a potential fi re hazard. Outlets in this condition should be replaced by a qualifi ed
electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means of disconnecting
power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug
™
on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed or tampered
with. To reduce the risk of fi re, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper with the originally supplied
plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fi t into the outlet only one way. Match the wide
blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the plug does not fi t in the outlet, consult a
qualifi ed electrician. The outlet may need to be replaced.
NEW 12/22NEW 12/22
NEW 9/22 7 T40733_T40735ES
1 Cuerpo
2 Base de Soporte A
3 Base de Soporte B
Controles Aplicación
™
Controlada
Este ventilador puede ser operado por los controles manuales ubicados en la parte
superior de la unidad o por los controles de la aplicación Aria en su dispositivo inteli-
gente. Para obtener una descripción detallada de cómo emparejar su producto con la
aplicación Aria, consulte la Guía de emparejamiento rápido.
Botón de
Retroceso
Botón de Tem-
porizador
Botón de Encendido
Botón de Oscilación
Botón Programar
(Característica exclusiva
de la aplicación)
Control Deslizante
de Velocidad
del Ventilador
Botón de control LED:
(Característica exclusiva de
la aplicación)
Use esta función para
habilitar el modo oscuro. El
modo oscuro apagará la in-
terfaz LED de su dispositivo
y solo la mostrará durante
5 segundos si se presiona
un botón.
Botón de
confi guración
Vaya a la página de
confi guración para
habilitar el control
inteligente del
altavoz y el uso
compartido de
dispositivos.
Partes Incluidas
2
3
1
Botón de Oscilación
Presione el Botón de Oscilación para iniciar y detener la
función de oscilación.
Botón de Encendido
ENCENDIDO/APAGADO el Ventilador presionando el
Botón de Encendido.
Botón de Velocidad
La velocidad del ventilador se puede ajustar a 1, 2, 3, 4 o 5.
Botón de Temporizador
El temporizador se puede confi gurar para 9 horas. Continúe
pulsando el Botón del Temporizador para llegar a la confi gu-
ración de tiempo deseada.
Botón de Wi-Fi
Appuyez sur le bouton Wi-Fi et maintenez-le enfoncé pendant
cinq secondes pour mettre l’appareil en mode d’appairage EZ.
L’indicateur LED commencera à clignoter en rouge lorsque
vous faites cela.
Remarque : si vous devez utiliser le mode AP pour connecter
votre produit, maintenez le bouton Wi-Fi enfoncé pendant cinq
secondes supplémentaires. La LED rouge commencera à
clignoter en rouge, rapidement.
Anulación de funciones inteligentes (Realice Uno de los Pasos Siguientes)
• Presione el botón deseado en el producto para anular cualquier confi guración remota inteligente.
• Restablezca el dispositivo para olvidar cualquier dispositivo conectado (restablecimiento de fábrica: mantenga presionado el bot
Wi-Fi durante 5 segundos).
• Desenchufe la unidad de la pared para evitar el acceso remoto inteligente.
1
2.
Coloque la unidad sobre una mesa resistente
para facilitar el montaje de la base. Empuje
la base ensamblada sobre el cuerpo de la
unidad, tal como se muestra.
Ensamblaje
1. Alinee las ranuras de la base A con las
lengüetas de la base B. Encájelas.
3.
Sostenga la estructura en su lugar mientras gira el
ensamblaje de la base de soporte en el sentido
de las agujas del reloj hasta que encaje en su lugar.
Base A
Base B
e
A
B
NEW 12/22NEW 12/22
Loading ...
Loading ...
Loading ...