Loading ...
Loading ...
Loading ...
Rev. K 5/13
4
5365ES
Rev. K 5/13
9
5365ES
MODEL 5365
Front View of
Remote Control
Figure 2
Rear View of
Remote Control
MODELO 5365
3. Arme la base enclavando las Protuberancias en los Orificios
para Protuberancias. (Figura 3)
5. Alinee el Conjunto de la Base con el Conjunto de Soporte de
Columna. Cerciórese de que la Muesca de Ubicación en el
Conjunto de Soporte de Columna quede alineada con la Llave
en el Conjunto de la Base (Figura 5). Una el Conjunto de la Base
al Conjunto de Soporte de Columna con (4) tornillos M5 X 13
mm. Jale suavemente el Cable Eléctrico para que no quede
holgado, y colóquelo en el Canal Para Cable del Conjunto de
la Base. (Figura 6)
1. Coloque el Cable Eléctrico en la parte inferior del Calefactor.
Pase el Cable Eléctrico por el centro del Conjunto de Soporte
de Columna.
2. Una el Conjunto de Soporte de Columna a la Base del Motor
con (4) tornillos M5 X 13mm. Cerciórese de que la Llave que
está en la Base del Motor quede alineada con la Muesca de
Ubicación en el Conjunto de Soporte de Columna. (Figura 2)
4. Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase
el Cable Eléctrico por el gran orificio que se encuentra del
Conjunto de la Base. NOTA: El Canal Para Cable en la parte
inferior de la base debe estar hacia la parte posterior del Calefactor.
(Figura 4)
Tamaño Real De Tornillos
Figura 3
Protuberancias
Figura 5
Conjunto de
la Base
Conjunto de
Soporte de
Columna
Orificios
para
Protuberancias
Llave
Cable Eléctrico
Figura 1
(8) - M5 X 13mm
(2) - M4 X 13mm
Figura 2
Conjunto de Soporte
de Columna
Cable
Eléctrico
Base del
Motor
Llave
Figura 4
Cable
Eléctrico
Conjunto de
la Base
Cable
Eléctrico
Figura 6
Llave
Muesca de
Ubicación
Canal Para
Cable
Canal Para
Cable
REMOTE CONTROL (Figure 2)
All the functions performed with the Remote Control work identi-
cally to the manual controls, except that you are unable to change
from °F to °C with the remote control.
1. Install two “AAA” batteries (not included).
2. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY
EXPLODE OR LEAK.
If you lose your remote control, please call Customer Service to
order a replacement at 1-800-233-0268, Monday through Friday,
between the hours of 8:00 a.m. and 5:00 p.m. EST.
ARMADO (Figuras 1 a 6)
Herramientas Necesarias: Destornillador de Cabeza #2 Phillips
(no incluido)
Retire cuidadosamente el Calefactor de su bolsa y caja. Para
facilitar el armado, coloque el Calefactor de manera que la parrilla
frontal y el panel de control den hacia arriba.
OPERATION
1. Place the Heater on a firm, level surface, after assembling
per this manual.
Plastic or rubber tabs, like the feet on this unit, may stick to
furniture surfaces and/or hardwood floors. The unit may leave a
residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces,
and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle
with only the slight movement of the attached cord.
Receptacles in this condition may overheat and pose
a serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
3. When the Heater is initially plugged in, there will be a “beep”
and the Power Light will come on indicating that there is power
to the unit. The Power Light will remain lit until the Heater is
unplugged from the electrical outlet. (Figure 1)
4. Turn the Heater ON by pressing the Power Button ( ).
5. When initially turned on, the Heater will display the current room
temperature in ° Fahrenheit. Press the ( ) and
( ) buttons
at the same time to change the display to ° Celsius. Press the
same two buttons together again to change the display back to
° Fahrenheit.
6. Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500
Watts) and will display the current room temperature. (Figure 1)
7. Press the ( ) button for LOW heat ( ).
8. To turn the Heater OFF, press the Power Button ( ) and unplug
the Heater from the electrical outlet.
OSCILLATION:
Pressing the Oscillation Button ( ) will allow the Heater to oscil-
late back and forth. To stop the oscillation, press the Oscillation
Button ( ) again. When the Heater is in Automatic Temperature
Control, the oscillation function will stop when the set temperature
is reached and resume when the Heater turns back on.
Display when initially turned on
Figure 1
AUTOMATIC TEMPERATURE CONTROL
Pressing the ( ) or ( ) button allows you to set the desired room
temperature.
1. When the ( ) or
( )
button is pressed, the displayed set tem-
perature will begin to flash and the ( ) symbol will appear.
2. Press the ( ) to increase the desired set temperature or
press
the ( )
to decrease the desired set temperature.
3. When the air temperature reaches 2° above the set temperature,
the Heater will shut off.
4. When the air temperature reaches 1° below the set temperature,
the Heater will turn on.
5. This function will cancel if the ( ) button is pressed and the
Heater will now be in High heat ( ).
NOTE: It is normal for the Heater “fan” to run for approximately 15 sec-
onds after the Heater shuts off after reaching the set temperature.
TIMER FUNCTION
The timer function may be activated when the Heater display is in
any function or speed. This function allows you to set the length
of time the Heater will run before turning itself off, from 1 hour to
8 hours. Pressing the Timer Button ( ) will increase the length of
time by 1 hour each time this button is pressed. After the display
reflects 8 hours, pressing the Timer Button ( ) once more will reset
the Heater to run continuously. The Heater will turn off when the
set time has elapsed. The unit can be turned back on by pressing
the Power Button ( ).
+
+
Loading ...
Loading ...
Loading ...