Bosch WAQ20320GR/07 Serie 6 Washing machine

Instruction manual - Page 5

For WAQ20320GR/07. Series: Serie 6

PDF File Manual, 6 pages, Read Online | Download pdf file

WAQ20320GR/07 photo
Loading ...
Loading ...
Loading ...
a
džƖơƗƖƟƚƥƑ
ićƅƢƜƴƬƞƩƨƫƢƝƖƩƱƥƚ
ƊƞƩƢƫƫƴƬƦƞƩƴ
ƆƥưƠƩƧƜ
ŻƩƖƔƧƝƜƨƖƈƩƢƝƚƨƞƟƑ
ićƅƢƜƴƬƞƩƨƫƢƝƖƩƱƥƚ
ƊƞƩƢƫƫƴƬƦƞƩƴ
ŷƢƑơƚƞƟƨƖ
ićƅƢƜƴƬƞƩƨƫƢƝƖƩƱƥƚ
ƊƞƩƢƫƫƴƬƦƞƩƴ
ƈƟƤƩƥưƫƥƭơƖ
i
ćƅƢƜƴƬƞƩƨƫƢƝƖƩƱƥƚ
ƊƞƩƢƫƫƴƬƦƞƩƴ
ƂƚƨƖƣƭƨƑ
i
ćƅƢƜƴƬƞƩƨƫƢƝƖƩƱƥƚ
ƊƞƩƢƫƫƴƬƦƞƩƴ
ÿ
ƂƑƠƠƞƢƖƣƩƵƨ
ŹƥƓƘƤƥƤ
ƄƒƗƘƖƠơƖƈƨƱƬƞơƤŮƢƨƠƜƧƜƢƚƥƤƱ
i
ä
NJƚƥƛƚƣƞƩƕ
NJƚƥƛƚƣƞƩƕ
NJƚƥƛƚƣƞƩƕ
NJƚƥƛƚƣƞƩƕ
ſƭƚƘƫơƠƬƚƌƭƦơƞƬƢƣƕ
ŻƦƕƥƞƢƣƬƚ
ƆƞƬƚƧƱƬƕ
ƆƕƤƤƢƦƚ
NJƚƥƛƚƣƞƩƕ
ć
10
Maintenance
Detergent solution pump
Turn the programme selector to Off and disconnect
the mains plug.
1. Using a screwdriver or the insert for liquid detergent
(depending on model), open and remove the service flap.
2. Remove the folding gutter and place a large enough container underneath.
3. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
from the housing.
Remove the sealing cap, allow the detergent solution to flow out into the container. Replace
the sealing cap and place the drainage hose in the retainer.
3* For models without a drainage hose: Carefully unscrew the pump cover 180° or until the
detergent solution begins to flow out on the folding gutter. When the container is full, close
the pump cover and empty the container. Repeat the above steps until all the detergent
solution has completely drained out.
4. Carefully unscrew the pump cover (there may be residual water).
5. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
6. Replace the pump cover and screw it tightly.
7. Return the drainage hose (depending on model) and the folding gutter to their start position.
8. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during the next wash:
Pour 2 litres of water into compartment II and then start the ŮƢƨƠƜƧƜƢƚƥƤƱ (Empty) programme.
Drainage hose at the siphon
Turn the programme selector to Off and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Filter in the water supply
Risk of electric shock!
Do not immerse the Aqua-Stop safety device in water (contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except ƄƒƗƘƖƠơƖ/ƈƨƱƬƞơƤ (Rinse/Spin) // ŮƢƨƠƜƧƜƢƚƥƤƱ
(Empty)).
3. Choose ŰƢƖƥƣƜ/ƊƚƵƫƠ (Start/Reload). Let the programme run for approximately 40
seconds.
4. Turn the programme selector to Off. Disconnect the mains plug.
Clean the filter:
5. Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and Aqua-Secure models:
Remove the hose on the rear of the appliance.
Remove the filter with pliers and clean.
6. Connect the hose and check for leaks.
Risk of burning!
Allow the detergent solution to cool.
Turn off the tap.
ʑ
ʑ
ŰƢƖƥƣƜƆƖƱƧƜ
a
ʑ
a
ƐƱƩƘƪƌƬƵưƢƥƨa
a
ʑ
ŰƢƖƥƣƜƆƖƱƧƜ
a
ʑ
ƐƱƩƘƪƌƬƵưƢƥƨa
a
ʑ
ʑ
ƁƞƘưƨƚƥƤƧƞƙƒƥƭơƖa
a
ʑ
ʑ
ʑ
a
ʑ
džƖơƗƖƟƚƥƑ
ʑ
ƆƠƱƧƜ
ʑ
a
a
ʑ
a
ʑ
ʑ
ƄƒƗƘƖƠơƖƈƨƱƬƞơƤ
a
Loading ...