Loading ...
Loading ...
Loading ...
Operation Guide 5576
E-49
To enable or disable Power Saving
1. In the Timekeeping Mode, hold down
A
for about two
seconds until ADJ is displayed.
• This displays the currently selected city code, and
then displays the setting screen.
2. Use
C
to cycle through the settings until the current
power saving setting (PSON or PSOF) is displayed.
• See the sequence in step 2 of the procedure under
“To change the current time and date settings” (page
E-27) for information about how to scroll between
settings.
3. Press
D
to toggle Power Saving between enabled (PSON) and disabled (PSOF).
4. After the setting is the way you want, press
A
to exit the setting screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
Power saving on indicator
E-48
2. Use
C
to cycle through settings until the current button operation tone (MUTE or
KEY
) is displayed.
• See the sequence in step 2 of the procedure under “To change the current time
and date settings” (page E-27) for information about how to scroll between settings.
3. Press
D
to toggle the button operation tone between enabled (KEY
) and disabled
(MUTE).
4. After the setting is the way you want, press
A
to exit the setting screen.
E-47
Other Settings
The button operation tone sounds any time you press one of the watch’s buttons. You
can enable or disable the button operation tone as desired.
• Even if you disable the button operation tone, the alarm, Hourly Time Signal, and
Countdown Timer Mode alarm all operate normally.
To enable or disable the button operation tone
1. In the Timekeeping Mode, hold down
A
for about two
seconds until ADJ is displayed.
• This displays the currently selected city code, and
then displays the setting screen.
Mute indicator
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
E-46
• The watch will return to regular timekeeping automatically if you do not perform
any operation for about two or three minutes. Any changes you have made to
settings up to that point will be saved.
• If the hour and minute hands are all at 12 o’clock, which is their home position,
jump to step 3.
2. Use
D
(+) and
B
(–) to adjust the hour and minute hand positions.
• High-speed hand movement started with the
D
(+) button will stop automatically
after 12 revolutions of the minute hand. If started with the
B
(–) button, it will
stop after one revolution of the minute hand.
3. Press
A
to exit home position correction and return to regular timekeeping.
Note
• After performing home position adjustment, enter the Timekeeping Mode and check
to make sure that the time indicated by the analog hands and the digital time are
the same. If they are not, perform home position adjustment again.
E-45
Hand Home Position Adjustment
Strong magnetism or impact can cause the analog time not to match the digital time. If
this happens, perform hand alignment.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
and keep it depressed for about five
seconds until H.SET is displayed.
• The hour and minute hands should all move to 12 o’clock, which is their home
position.
• Though ADJ will appear about two seconds after you hold down
A
, do not
release the button yet. Keep it depressed until H.SET is displayed. When H.SET
appears, release the
A
button. This will cause the hour and minute hands to
move to 12 o’clock.
• To return to the Timekeeping Mode, hold down
A
for at least eight seconds.
E-44
Illumination
An LED light (Super Illuminator) uses a light guide panel
to illuminate the face of the watch for easy reading in the
dark.
• See “Illumination Precautions” below for other important
information.
To turn on illumination
In any mode (except when a setting screen is displayed),
press
B
to illuminate the face of the watch for about one
second.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
E-43
To turn the alarm on or off
1. In the Alarm Mode, press
D
to select the alarm or the
Hourly Time Signal screen.
2. Press
A
to toggle the displayed alarm between on and
off.
• The alarm status is indicated on the display by
ALON
(alarm on) or
ALOF
(alarm off).
To stop a sounding alarm
Press any button.
To turn the hourly time signal on or off
1. In the Alarm Mode, use
D
to select the hourly time signal.
2. Press
A
to toggle the hourly time signal between on and off.
• The hourly time signal status is indicated on the display by OFF (hourly time
signal off) or ON (hourly time signal on).
On/Off status
E-42
To set the alarm time
1. In the Alarm Mode, press
D
to display the alarm
screen.
2. Hold down
A
until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press
C
to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to
change it.
• When setting the alarm time using the 12-hour
format, take care to set the time correctly as a.m. (no
indicator) or p.m. (
P
indicator).
5. Press
A
to exit the setting screen.
Alarm time
(Hour : Minutes)
l
l
l
l
l
l
l
l
l
l
l
E-41
Using the Alarm
When an alarm is turned on, an alarm tone will sound for
about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is
true even if the watch is not in the Timekeeping Mode.
You can also enable an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
• Pressing
D
in the Alarm Mode toggles between the
alarm screen and Hourly Time Signal screen.
• When the alarm is turned on, the alarm screen
alternates between
ALON
(alarm on) and the current
alarm time (hour and minutes). When the alarm is off,
ALOF
(alarm off) remains on the alarm screen.
To enter the Alarm Mode
Use
C
to select the Alarm Mode as shown on page E-21.
On/Off status
2-second
intervals
Alarm Screen
Hourly Time
Signal Screen
Press
D
.
E-40
To measure two finishes
D
A D A A
Start Split
(
SPL
displayed)
First runner
finishes.
Display time of
first runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
Note
• The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59.99 seconds.
• An ongoing elapsed time measurement operation will continue internally even if you
change to another mode. However, if you exit the Stopwatch Mode while a split
time is displayed, the split time will not be displayed when you return to the
Stopwatch Mode.
Loading ...
Loading ...
Loading ...