Loading ...
Loading ...
Loading ...
FOR YOUR SAFETY READ BEFORE LIGHTING
explosion may result causing property damage, personal injury or loss of life.
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.
A. This appliance hasa pilotwhichmust belighted by hand.
When lightingthe pilot,follow these instructions exactly. If you cannot reach your gas supplier, call the fire
department.
B. BEFORE LIGHTING small all aroundthe appliance area
for gas. Be sureto smell next tothe floor because some
gas is heavier than air and will settle on the floor.
WHATTO DOIF YOU SMELL GAS:
DOnot try to lightany appliance.
Donot touchanyelectricswitch; do not useany phone
inyour building.
Immediately call your gas supplier from a neighbor's
phone.Follow the gas supplier's instructions.
C.
D.
Use only your hand to push in or turn the gas control
knob. Never usetools. Ifthe knob will not push in or turn
by hand, don't try to repair it, call a qualified service
technician. Force or attempted repairmay resultinafire
or explosion.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspectthe appliance and to replace any part of the
control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS
GAB CONTROL KNOB
pIEZO
IGNITOR
_ENERATOR
THERMOSTAT
DIAL
GAS CONTROL
FIGURE "A" FIGURE "B" FIGURE "C"
"OFF POSITION "PILOT" POSITION "ON" POSITION
TOPKNOB
MAIN BURNER
/
FIGURE "D"
1. (_ STOP! Read the safety information
above on this label.
2. Set the thermostat to lowest setting (PILOT SETTING).
Turn thermostat dial fully clockwise t'_ until it stops.
3. Push thegas control knobdown slightlyand turnclockwise
f'_ to"OFF", SEE FIGURE "A".
NOTE: Knob CANNOT beturned from "PILOT" to"OFF"
unless it is pushed down slightly. Do not force.
4. Remove the outer burner door located below the gas
control.
5. Wait five (5) minutes to clear out any gas. If you then
smell gas,_) STOP! Follow"B"in the safetyinformation
above on this label. Ifyou don't smell gas, goto next step.
6. This unit isequipped with a push button pilot ignitor,which
is used to light the pilot. Locate the ignitor on the gas
control.
7. Turn gas centre] knob counterclockwise _ to"PILOT",
SEEFIGURE "B".
8. The pilotis locatedon the rightside ofthe burner. Itcan be
located by looking through the glass view port while
pressing the piezo ignitor button several times. Lookfora
sparkat the pilotlocation, FIGURE"D".
9. Once the pilot has been found, push the gas knob all the
way down. Immediately pressthe pilotignitorbutton rapidly
(4) to (5) times. If the pilot will not light, repeat step (3)
through (9).
10. Continue to hold the gas control knob down for about one
(1) minute after the pilot is lit. Release the gas control knob
and it will pop back up. Pilot should remain lit.If itgoes out,
repeat step (3) through (9). Itmay take several minutes for
air to clearthe lines before the pilotwill light.
If knob does not pop up when released, stop and
immediatelycall your service technician or gas supplier.
If the pilotwill not stay lit after several tries, turn the gas
control knob clockwise f_ to "OFF" and call your service
technician orgas supplier. SEE FIGURE "A".
11. Once the pilotflame is established replace the outer burner
door.
12. At arms length away, turn gas control knob
counterclockwise _ to"ON". SEE FIGURE "C".
13. Set thermostat todesired setting.
DANGER: Hotter water increases the risk of
scald injury. Consult the instruction manual
before changing temperature.
TO TURN OFF GAS TO APPLIANCE
2 Push gas control knob down shghgyand turn clockwise
I'L Set thermostatto the lowestsetting(PILOT LIGHTING). • " '
/'_ to"OFF". Do not force. SEE FIGURE "A".
18
Loading ...
Loading ...
Loading ...