EVID‑S Surface Mount Loudspeakers
en
Installation manual
EVID-S Surface Mount LoudspeakersTable of contents | en3
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
Table of contents
1
Safety4
1.1Suspension4
1.2Notices4
2
Short information5
3
Introduction6
3.1System features6
3.2Packing list7
3.3Product information9
4
Installation and wiring10
4.1Installing the speaker10
4.2Wiring14
4.2.1Wall bracket wiring14
4.2.2Alternative Euroblock connection14
4.3Transformer taps16
4.3.1EVID-S4.2T speaker 4” cabinet 70/100V16
4.3.2EVID-S5.2T speaker 5” cabinet 70/100V17
4.3.3EVID-S8.2T speaker 8” cabinet 70/100V17
4.4Replacing the logo18
5
Troubleshooting20
6
Technical data21
6.1EVID-S4.2/EVID-S4.2T speakers21
6.1.1Dimensions22
6.1.2Frequency response and impedance22
6.2EVID-S5.2/EVID-S5.2T speakers23
6.2.1Dimensions24
6.2.2Frequency response and impedance24
6.3EVID-S8.2/EVID-S8.2T speakers25
6.3.1Dimensions26
6.3.2Frequency response and impedance26
7
Wall bracket dimensions27
7.1EVID-S4.2/EVID-S4.2T wall bracket dimensions27
7.2EVID-S5.2/EVID-S5.2T/EVID-S8.2/EVID-S8.2T wall bracket dimensions28
4en | SafetyEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
1Safety
1.1Suspension
!
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals
who have a thorough knowledge of the techniques and regulations of suspending objects
overhead. Electro-Voice strongly recommends that loudspeakers be suspended taking into
account all current national, federal, state, and local laws and regulations. It is the
responsibility of the installer to ensure all loudspeakers are safely installed in accordance
with all such requirements. When loudspeakers are suspended, Electro-Voice strongly
recommends the system be inspected at least once per year or as laws and regulations
require. If any sign of weakness or damage is detected, remedial action should be taken
immediately. The user is responsible for making sure the wall, ceiling, or structure is capable
of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker
not associated with Electro-Voice is the responsibility of others.
Safety point
As an added safety measure, it is suggested the user install an extra suspension point back to
the building structural supports. This safety point should have as little slack as possible (less
than 1-inch is preferable).
Figure1.1: Redundant safety point - 4" (left), 5" (center), 8" (right)
1.2Notices
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and
sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection
systems put in place in the country concerned.
Copyright and disclaimer
All rights reserved. No part of this document may be reproduced or transmitted in any form by
any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of the publisher. For information on getting permission for reprints and
excerpts, contact Electro-Voice.
All content including specifications, data, and illustrations in this manual are subject to change
without prior notice.
EVID-S Surface Mount LoudspeakersShort information | en5
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
2Short information
The following table lists products in a family, with CTN (Commercial Type Number) and
identifying product name DESCRIPTION.
Woofer sizeCTNDescription
4"EVID-S4.2BSpeaker 4” cabinet 8 Ohm black pair
EVID-S4.2WSpeaker 4” cabinet 8 Ohm white pair
EVID-S4.2TBSpeaker 4” cabinet 70/100V black pair
EVID-S4.2TWSpeaker 4” cabinet 70/100V white pair
5.25"EVID-S5.2BSpeaker 5” cabinet 8 Ohm black pair
EVID-S5.2WSpeaker 5” cabinet 8 Ohm white pair
EVID-S5.2TBSpeaker 5” cabinet 70/100V black pair
EVID-S5.2TWSpeaker 5” cabinet 70/100V white pair
8"EVID-S8.2BSpeaker 8” cabinet 8 Ohm black pair
EVID-S8.2WSpeaker 8” cabinet 8 Ohm white pair
EVID-S8.2TBSpeaker 8” cabinet 70/100V black pair
EVID-S8.2TWSpeaker 8” cabinet 70/100V white pair
6en | IntroductionEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
3Introduction
The EVID-S series from Electro-Voice is a line of compact, high-performance, two-way, full-
range surface mount loudspeakers with excellent wide and uniform coverage, and outstanding
performance. Their design makes these practically invisible for use in background and
foreground music, paging, and sound reinforcement applications, making EVID-S ideal for
indoor and outdoor applications, such as restaurants, bars, patios, retail, fitness clubs,
hospitality, theme parks, leisure venues, and others. With unparalleled ease-of-installation,
sturdy weather resistance, modern and delicate look, and flexible mounting options, the EVID-
S series is the perfect solution for a wide variety of surface mount applications.
All EVID-S series full-range loudspeakers (except for the EVID-S5.2X) include a unique and
innovative mount system from Electro-Voice, prepared to make any job easier. This mount
system allows for 90 degrees of rotation horizontally and 45 degrees of rotation vertically. It
comes already assembled and is easily installed on walls and ceilings. Its unique and
innovative mount system makes every installation quick, simple, and reliable.
Read through this manual to familiarize yourself with the safety information, features, and
applications before you use these products.
3.1System features
EVID-S4.2/EVID-S4.2T
–Innovative mount system is included for quick, simple, and reliable installations
–Carefully engineered for outdoor environments (IP54), without compromising
performance
–Long throw 4" (102 mm) woofer housed in a fire rated ABS plastic enclosure for extended
LF performance down to 75 Hz
–40 W power handling provides for 103 dB maximum SPL (109 dB peak)
–70/100 V transformer version (EVID 4.2T) available for constant voltage systems
EVID-S5.2/EVID-S5.2T
–Innovative mount system is included for quick, simple, and reliable installations
–Carefully engineered for outdoor environments (IP54), without compromising
performance
–Long throw 5.25" (133 mm) woofer housed in a fire rated ABS plastic enclosure for
extended LF performance down to 60 Hz
–75 W power handling provides for 109 dB maximum SPL (115 dB peak)
–70/100 V transformer version (EVID 5.2T) available for constant voltage systems
EVID-S8.2/EVID-S8.2T
–Innovative mount system is included for quick, simple, and reliable installations
–Carefully engineered for outdoor environments (IP54), without compromising
performance
–Long throw 8" (203 mm) woofer housed in a fire rated ABS plastic enclosure for extended
LF performance down to 50 Hz
–90 W power handling provides for 110 dB maximum SPL (116 dB peak)
–70/100 V transformer version (EVID 8.2T) available for constant voltage systems
EVID-S Surface Mount LoudspeakersIntroduction | en7
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
3.2Packing list
ItemQuantityComponent
A2Speakers with speaker brackets attached
B2Wall mount brackets
C2Dust covers
D1Allen wrench
E2Grille logos (spare)
F2Safety screws for the mounting brackets
G2Safety screw caps for the mounting brackets
H2Covers for the locking bolt
I1Installation manual
Tab.3.1: Components list for speakers without transformer
A (x2)
B (x2)
D
C (x2)
E (x2)
F (x2)
G (x2)
H (x2)
I
Figure3.1: Components list for speakers without transformer
8en | IntroductionEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
ItemQuantityComponent
A2Speakers with speaker brackets attached
B2Wall mount brackets
C2Dust covers
D1Allen wrench
E2Grille logos (spare)
F2Safety screws for the mounting brackets
G2Safety screw caps for the mounting brackets
H2Covers for the locking bolt
I1Installation manual
J2Flush input covers
K8Screws for flush input covers
Tab.3.2: Components list for speakers with transformer
A (x2)
B (x2)
D
C (x2)
E (x2)
F (x2)
G (x2)
H (x2)
I
J (x2)
K (x8)
Figure3.2: Components list for speakers with transformer
EVID-S Surface Mount LoudspeakersIntroduction | en9
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
3.3Product information
ItemDescription
AGrille
BBubble level
CWall bracket
DSafety cable loop
EFlush input cover
FAudio wire hole
GLocking bolt
HAudio connector
ISafety screw hole for bracket
JSpeaker bracket
Tab.3.3: Product information for all models
A
B
C
J
I
H
G
F
E
D
10en | Installation and wiringEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
4Installation and wiring
4.1Installing the speaker
For safety, ensure the mounting surface supports more than the weight of the speaker. Use
only industry-accepted fasteners and mounting methods when mounting the wall bracket.
Consult an expert if you are unsure.
!
Caution!
It is the installer's responsibility to determine and use the proper mounting hardware for the
wall construction type.
Disregarding this caution could result in damage to the product and personal injuries may
occur.
Installing the wall bracket vertically
To install the wall bracket vertically, do the following:
1.Push the wire thru the hole.
2.Adjust the wall bracket until the bubble is level.
3.Install four mounting screws to secure the wall bracket to the wall.
4.Connect the wires to wall bracket audio connectors, as shown in the wiring section.
Notice!
If the speaker installation will be delayed cover it with the paint shield/dust shield.
EVID-S Surface Mount LoudspeakersInstallation and wiring | en11
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
Installing the wall bracket horizontally
To install the bracket horizontally, do the following:
1.Draw a level line.
2.Align screw holes on the level line.
3.Mark the position of the wire hole.
4.Install four mounting screws to secure the wall bracket to the wall.
Notice!
If the speaker installation will be delayed cover it with the paint shield/dust shield.
Installing the speaker
To install the speaker, do the following:
1.Loosen the locking bolt with the Allen wrench (supplied).
2.Adjust the horizontal and vertical position of the bracket.
3.Tighten the locking bolt with an Allen wrench (supplied).
If available, we recommend using an Allen wrench with a longer handle to make it easier to
apply the necessary force to achieve the recommended torque. See Recommended torque,
12en | Installation and wiringEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
page 13
4.Push the speaker bracket onto the wall bracket.
5.Slide the speaker bracket down to secure bracket to the wall bracket.
This secures the bracket and makes electrical connection.
EVID-S Surface Mount LoudspeakersInstallation and wiring | en13
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
6.Install the safety screw and screw cap.
7.Readjust the horizontal and vertical speaker position, if needed.
8.Install the locking bolt cap.
Recommended torque
Speaker sizeRecommended torque
4" speakers62-75 in.-lb. (7.0-8.5 N-m)
5.25" speakers66-80 in.-lb. (7.5-9.0 N-m)
8" speakers66-80 in.-lb. (7.5-9.0 N-m)
Tab.4.4: Recommended torque
Safety point
As an added safety measure, it is suggested the user install an extra suspension point back to
the building structural supports. This safety point should have as little slack as possible (less
than 1-inch is preferable).
Figure4.1: Redundant safety point - 4" (left), 5" (center), 8" (right)
14en | Installation and wiringEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
4.2Wiring
4.2.1Wall bracket wiring
The wall bracket and speaker can be wired using either 2-wires, for input only, or 4-wires, for
input and parallel output.
Figure4.2: Wall bracket wiring - 2-wires, for input only
Figure4.3: Wall bracket wiring - 4-wires, for input and parallel output
Reference the polarity markers on the wall bracket. Ensure the wiring screws are tightened
securely to the connectors on the wall bracket.
Figure4.4: Wall bracket wiring - front view
4.2.2Alternative Euroblock connection
Notice!
These instructions apply to the speakers with and without transformers, transformer version
shown. Available for all models except EVID-S4.2T.
EVID-S Surface Mount LoudspeakersInstallation and wiring | en15
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
Wiring the speaker using the Euroblock connector
To wire the speaker using Euroblock connector, do the following:
1.Wire the Euroblock connector.
2.Adjust the tap settings, if needed.
3.Mount the speaker, as shown in the installation section.
4.Plug the Euroblock connector into the speaker.
5.Readjust the horizontal or vertical speaker position.
Wiring the speaker using the Euroblock connector and weather cover – optional accessory
To wire the speaker using Euroblock connector and weather cover, do the following:
1.Push the wire through the gland nut.
2.Wire the Euroblock connector (A).
A
B
C
3.Adjust the tap settings, if needed.
4.Mount the speaker, as shown in the installation section.
5.Plug the Euroblock connector into the speaker.
6.Insert the four screws into the weather cover (B).
Loosely tighten the four screws to keep the weather cover in place.
7.Tighten all four screws to secure the weather cover.
Ensure the weather cover is secure.
8.Adjust the wire length.
9.Tighten the gland nut (C).
10.Readjust the horizontal or vertical speaker position.
See also
–Installing the speaker, page 10
16en | Installation and wiringEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
4.3Transformer taps
You can select the mode of operation for all models that have a transformer. For the EVID-
S4.2T you can select the power tap for 70V/100V operation by using the jumper connector in
the Euroblock on the input panel. For the EVID-S5.2T and the EVID-S8.2T you can select the
mode of operation (70V/100V/8 ohm) and power taps using the rotary switch on the input
panel.
4.3.1EVID-S4.2T speaker 4” cabinet 70/100V
Configuring the transformer settings
To configure the transformer settings, do the following:
1.Remove the Euroblock connector from the input panel.
2.Wire the jumper connector in the Euroblock, according to the desired transformer
settings.
3.Plug the Euroblock connector into the input panel.
EVID-S Surface Mount LoudspeakersInstallation and wiring | en17
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
4.Attach the flush input cover (A).
A
4.3.2EVID-S5.2T speaker 5” cabinet 70/100V
Configuring the transformer settings
To configure the transformer settings, do the following:
1.Select the desired power tap by using the rotary switch on the input panel.
+
A
2.If 8 ohm mode is desired, remove the safety screw.
Safety screw (A) is shown in the previous step.
3.Attach the flush input cover (B).
B
4.3.3EVID-S8.2T speaker 8” cabinet 70/100V
Configuring the transformer settings
To configure the transformer settings, do the following:
18en | Installation and wiringEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
1.Select the desired power tap by using the rotary switch on the input panel.
+
A
2.If 8 ohm mode is desired, remove the safety screw.
Safety screw (A) is shown in the previous step.
3.Attach the flush input cover (B).
B
4.4Replacing the logo
An additional logo is included, horizontal installation is shown.
To replace the logo, do the following:
1.Remove the existing logo.
2.Clean the surface with alcohol.
3.Align the logo with the logo recess on the grille.
4.Remove the paper backing.
EVID-S Surface Mount LoudspeakersInstallation and wiring | en19
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
5.Insert the logo.
Press firmly to ensure the logo is applied.
20en | TroubleshootingEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
5Troubleshooting
ProblemPossible CausesAction
No SoundAmplifierConnect a known working test speaker to the amplifier outputs. If
there is no sound, check all electronics are on, the signal routing is
correct, the source is active; the volume is turned up, and so on.
Correct/Repair/Replace as necessary. If there is sound, the problem is
in the wiring.
WiringVerify you have connected the correct wire pairs to the amplifier. Play
something at low level through the amplifier (for example, from a CD
player or tuner). Connect the test speaker in parallel with the
malfunctioning line. If the sound has gone or is very weak, the line has
a short in it (possibly a severe scrape, pinch, or staple puncture). If
the sound level is normal the wire is open (possibly a cut wire or
missed connection). Using the test speaker, move down the line and
test each connection/junction until you find the problem and correct
it. Observe proper polarity.
Verify you have the inputs and outputs connected to the correct wires.
If the subwoofer input panel is not correctly wired, there will be little
or no sound. Observe proper polarity.
Poor Low-
Frequency
Response
Speakers Wired Out-
of-Polarity
When two speakers are connected out of polarity (out of phase), the
low frequencies will cancel each other acoustically. Carefully observe
the wire markings or tracers on your speaker wires. Verify the
amplifier (+) terminal is connected to the red speaker terminals and
the amplifier (-) terminal is connected to the black speaker terminals.
Improperly Wired
Subwoofer Panel
Using a test speaker as described above, verify all amplifier and
speaker wires are connected to their proper terminals with the correct
polarity. Reversing just one set of amplifier wires can cut out all bass
output from the subwoofer.
Intermittent
Output such as,
Crackling or
Distortion
Faulty ConnectionCheck all connections at amplifier and speakers to ensure they are
clean and tight. If the problem persists, it may be in the amplifier or
wiring. See other actions above.
Constant Noise
such as Buzzing,
Hissing, Humming
Defective Amplifier
or other Electronic
Device
If the noise is present but no program material is playing, the likely
cause is the signal chain in the electronics. Evaluate each component
as necessary to isolate the problem.
Poor System
Grounding or
Ground Loop
Check and correct the system grounding, as required.
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or
Electro-Voice distributor.
EVID-S Surface Mount LoudspeakersTechnical data | en21
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
6Technical data
6.1EVID-S4.2/EVID-S4.2T speakers
EVID-S4.2EVID-S4.2T
Frequency response (-3 dB):100 Hz – 20 kHz
1
100 Hz – 20 kHz
1
Frequency response (-10 dB):75 Hz – 20 kHz
1
75 Hz – 20 kHz
1
Sensitivity:87 dB
2
86.5 dB
2
Max SPL (calculated):103 dB (109 dB Peak)98.5 dB (104.5 dB Peak)
Coverage angle:Horizontal 110°, Vertical 110°
Power handling:40 W (160 W Peak)
Continuous Pink Noise (100
hours)
15 W (60 W Peak) Continuous
Pink Noise (100 hours)
Low Z:YesNo
Nominal impedance:8 ΩN/A
Minimum impedance:6 ΩN/A
Recommended High-Pass:70 Hz (24 dB/octave)
Input transformer (70V/100V):No15 W
Transformer taps:N/A70 V: 3.7 W, 7.5 W, 15 W
100 V: 7.5 W, 15 W
LF transducer:4 inch (102 mm)
HF transducer:0.75 inch (20 mm)
Connectors:Captive screws on wall
bracket. Removable locking
4-pin connector (Euroblock)
– (2) for connection to
additional speakers in a
distributed line. Max. wire
size 12AWG (2.5 mm).
Captive screws on wall
bracket. Max. wire size
12AWG (2.5 mm).
Environmental:IP54 (per IEC-60529)
Color:Black (RAL 9004) or white (RAL 9003)
Dimensions (H x W x D):193 mm x 140 mm x 118 mm (7.6 in x 5.5 in x 4.7 in)
3
Net weight:1.5 kg (3.3 lb)1.8 kg (4.0 lb)
Shipping weight (pair):5 kg (11.0 lb)5.4 kg (11.9 lb)
Included hardware:Mounting bracket and 4-mm Allen wrench
Packaged quantity:2
1
Half-space (wall mounting).
2
Half-space (on wall) averaged 100 Hz - 10 kHz, 1 W.
3
Without brackets.
22en | Technical dataEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
6.1.1Dimensions
140.0 mm
[5.51 in]
118.2 mm
[4.66 in]
184.0 mm
[7.24 in]
193.0 mm
[7.60 in]
Figure6.1: EVID-S4.2/EVID-S4.2T dimensions
6.1.2Frequency response and impedance
Figure6.2: EVID-S4.2/EVID-S4.2T frequency response and impedance
EVID-S Surface Mount LoudspeakersTechnical data | en23
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
6.2EVID-S5.2/EVID-S5.2T speakers
EVID-S5.2EVID-S5.2T
Frequency response (-3 dB):85 Hz – 20 kHz
1
Frequency response (-10 dB):60 Hz – 20 kHz
1
Sensitivity:90 dB
2
Max SPL (calculated):109 dB (115 dB Peak)
Coverage angle:Horizontal 90°, Vertical 90°
Power handling:75 W (300 W Peak) Continuous Pink Noise (100 hours)
Low Z:Yes
Nominal impedance:8 Ω
Minimum impedance:6 Ω
Recommended High-Pass:60 Hz (24 dB/octave)
Input transformer (70 V/100 V):No30 W
Transformer taps:N/A70 V: 3.7 W, 7.5 W, 15 W, 30
W, 8 Ω
100 V: 7.5 W, 15 W, 30 W, 8
Ω
LF transducer:5.25 inch (133 mm)
HF transducer:0.75 inch (20 mm)
Connectors:Captive screws on wall bracket.
Removable locking 4-pin connector (Euroblock) – (2) for
connection to additional speakers in a distributed line.
Max. wire size 12AWG (2.5 mm)
Environmental:IP54 (per IEC-60529)
Color:Black (RAL 9004) or white (RAL 9003)
Dimensions (H x W x D):255 mm x 180 mm x 151 mm (10.0 in x 7.1 in x 6.0 in)
3
Net weight:2.7 kg (5.9 lb)
3
3.2 kg (7.0 lb)
3
Shipping weight (pair):6.7 kg (14.8 lb)7.9 kg (17.5 lb)
Included hardware:Mounting bracket and 5-mm Allen wrench
Packaged quantity:2
1
Half-space (wall mounting).
2
Half-space (on wall) averaged 100 Hz - 10 kHz, 1 W.
3
Without brackets.
24en | Technical dataEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
6.2.1Dimensions
180.1 mm
[7.09 in]
151.2 mm
[5.95 in]
240.0 mm
[9.45 in]
255.0 mm
[10.04 in]
Figure6.3: EVID-S5.2/EVID-S5.2T dimensions
6.2.2Frequency response and impedance
Figure6.4: EVID-S5.2/EVID-S5.2T frequency response and impedance
EVID-S Surface Mount LoudspeakersTechnical data | en25
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
6.3EVID-S8.2/EVID-S8.2T speakers
EVID-S8.2EVID-S8.2T
Frequency response (-3 dB):70 Hz – 20 kHz
1
Frequency response (-10 dB):50 Hz – 20 kHz
1
Sensitivity:90 dB
2
Max SPL (calculated):110 dB (116 dB Peak)
Coverage angle:Horizontal 90°, Vertical 90°
Power handling:90 W (360 W Peak) Continuous Pink Noise (100 hours)
Low Z:Yes
Nominal impedance:8 Ω
Minimum impedance:6 Ω
Recommended High-Pass:50 Hz (24 dB/octave)
Input transformer (70 V/100 V):No60 W
Transformer taps:N/A70 V: 7.5 W, 15 W, 30 W, 60
W, 8 Ω
100 V: 15 W, 30 W, 60 W, 8
Ω
LF transducer:8 inch (203 mm)
HF transducer:1 inch (25 mm)
Connectors:Captive screws on wall bracket.
Removable locking 4-pin connector (Euroblock) – (2) for
connection to additional speakers in a distributed line.
Max. wire size 12AWG (2.5 mm)
Environmental:IP54 (per IEC-60529)
Color:Black (RAL 9004) or white (RAL 9003)
Dimensions (H x W x D):390 mm x 250 mm x 223 mm (15.4 in x 9.8 in x 8.8 in)
3
Net weight:5.1 kg (11.3 lb)
3
5.8 kg (12.8 lb)
3
Shipping weight (pair):13.0 kg (28.7 lb)14.8 kg (32.6 lb)
Included hardware:Mounting bracket and 5-mm Allen wrench
Packaged quantity:2
1
Half-space (wall mounting).
2
Half-space (on wall) averaged 100 Hz - 10 kHz, 1 W.
3
Without brackets.
26en | Technical dataEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
6.3.1Dimensions
250.0 mm
[9.84 in]
223.2 mm
[8.79 in]
311.0 mm
[12.24 in]
390.2 mm
[15.36 in]
Figure6.5: EVID-S8.2/EVID-S8.2T dimensions
6.3.2Frequency response and impedance
Figure6.6: EVID-S8.2/EVID-S8.2T frequency response and impedance
EVID-S Surface Mount LoudspeakersWall bracket dimensions | en27
Electro-VoiceInstallation manual2018-10 | 02 | F.01U.345.360
7Wall bracket dimensions
The wall bracket dimensions are not to scale and are for reference only.
7.1EVID-S4.2/EVID-S4.2T wall bracket dimensions
+
-
15.5 mm
[0.6 in]
93.5 mm
[3.7 in]
15.9 mm
[0.6 in]
4x ∅4.5 mm
[4x ∅0.177 in]
117.0 mm
[4.6 in]
51.8 mm
[2.04 in]
∅8.0 mm
[∅0.315 in]
15.9 mm
[0.6 in]
28en | Wall bracket dimensionsEVID-S Surface Mount Loudspeakers
2018-10 | 02 | F.01U.345.360Installation manualElectro-Voice
7.2EVID-S5.2/EVID-S5.2T/EVID-S8.2/EVID-S8.2T wall bracket
dimensions
+
-
21.0 mm
[0.83 in]
127.0 mm
[5.0 in]
19.5 mm
[0.8 in]
156.0 mm
[6.1 in]
69.1 mm
[2.72 in]
4x ∅4.5 mm
[4x ∅0.177 in]
∅8.0 mm
[∅0.315 in]
19.5 mm
[0.8 in]
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2018
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com
