Loading ...
Lasko
FUNCIONAMIENTO Figura 1
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
Los
tacos de plástico o hule, tales como las patas de esta unidad,
pueden pegarse a la superficie de los muebles y/o a los pisos de
madera. La unidad podría dejar un residuo capaz de oscurecer,
manchar o dejar marcas permanentes en el acabado de ciertas
superficies de muebles, incluyendo superficies de madera y/o
pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un peligro de incendio grave; si queda cubierto por
una cortina o tela, el peligro de incendio es todavía
mayor.
4. Cuando el Calefactor se conecte por primera vez, la Luz de
Encendido se encenderá indicando que hay electricidad en la
unidad. La Luz de Encendido permanecerá encendida hasta
que el Calefactor sea desconectado del tomacorriente eléctrico.
5. ENCIENDA el Calefactor oprimiendo el Botón de Encendido.
6. Cuando se lo encienda por primera vez, el Calefactor estará en
NEW 6/14
2
CT16511ES
NEW 6/14
7 CT16511ES
MODELO CT16511
Figura 1
Botón De
Oscilación
Botón De Encendido
Botón De
Temperatura
Calor Bajo
Calor Alto
calor Alto (1500 vatios) en Máx. (La luz Alta estará encendida
permanentemente y la luz de Máximo estará titilando).
7. Oprima el Botón de Encendido una vez más y el Calefactor
estará en Calor Bajo, indicado por la luz permanente junto a Bajo.
8. Oprimir el Botón de Encendido por tercera vez APAGARÁ el
Calefactor.
9. Cuando el Calefactor está APAGADO, la luz roja en la parte frontal
del Calefactor permanecerá encendida hasta que el Calefactor
sea desconectado del tomacorriente eléctrico.
Función de Oscilación:
1. Oprimir el Botón de Oscilación (OSC) le permitirá al Calefactor
oscilar hacia atrás y hacia delante. Para detener la oscilación,
vuelva a oprimir el Botón de Oscilación (OSC). Cuando el
calefactor esté en control automático de temperatura, la función
de oscilación se detendrá cuando se alcance la temperatura
fijada y reiniciará cuando el calefactor vuelva a encenderse.
Función de Temperatura
La función de temperatura automática sólo operará en calefacción
“Alta”. No puede fijar la temperatura automáticamente cuando la
unidad se encuentre en la modalidad de calefacción baja.
1. Para fijar una temperatura específica en la habitación, presione
el botón de temperatura (TEMP) hasta la configuración deseada.
La luz de la temperatura escogida continuará titilando hasta que la
habitación alcance la temperatura deseada. El Calefactor realizará
el ciclo de apagado y encendido para mantener la temperatura
de la habitación. Cuando se fija en MAX (Máximo), el Calefactor
operará continuamente.
Luz de
Encendido
SAVE THESE INSTRUCTIONS
• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET
ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT
PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS
TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING.
IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended.
Never leave children unattended when the heater is on or plugged in.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where
flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked.
Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug
the power cord.
Read all instructions before using this Heater.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
WARNING
CAUTION
• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep com-
bustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
• DO NOT use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to
National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricul-
tural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local
codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS
OF NEC ARTICLE 500 (2008).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equip-
ment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or
an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
WARNING
Loading ...
Loading ...
Loading ...