Loading ...
Loading ...
Loading ...
Manual
There are two manual cycles: Time Dry and Quick Dry. These
cycles will run for the set number of minutes shown on the dig-
ital display. The cycle time can be increased or decreased us-
ing the up and down arrow keypads. Select the temperature
based on the fabric care label. The time and temperature se-
lection may be adjusted manually at any time before or during
the cycle. The time may need to be adjusted up if the items
are still damp or down if the items are overdry.
Steam
The Steam Sanitize cycle sanitizes your laundry by killing
99.9% of common household bacteria*. It is a 75-minute cycle
that applies high-temperature heat to sanitize the load, as well
as steam to help keep your laundry soft and wrinkle free. It is
recommended for medium size loads and is not recommend-
ed for all fabric types. Be sure to follow fabric care labels.
To use Steam Sanitize, press the Steam Sanitize keypad and
allow the cycle to complete uninterrupted. Time can be extend-
ed higher than 75 minutes by using the up and down arrow
keypads.
NOTE: The Sanitize setting uses high heat. Check the
fabric label for proper care instructions.
The Steam Refresh cycle releases wrinkles and refreshes your
items. It is recommended for 1-4 items. There are two preset
cycles. The default cycle applies a medium-temperature heat
for 30 minutes to the load. The alternate cycle applies a high-
temperature heat for 20 minutes.
To use Steam Refresh, press the Steam Refresh keypad and
the default cycle for 30 minutes at medium heat will be initiat-
ed. To initiate the 20-minute, high-heat cycle, toggle the Temp
selection to High. Select the 30-minute medium heat or 20-mi-
nute high heat temperature based on fabric type.
*Bacteria tested by an independent lab were Staphylococcus
aureus, Pseudomonas aeruginosa, Klebsiella pneumoniae. In-
dividual results may vary.
IMPORTANT: Do not use dryer sheets when using
steam cycles.
IMPORTANT: Do not run steam with no load to help
prevent water from staining the cylinder.
NOTE: Do not overload machine for steam cycles.
Overloading during a steam cycle may cause the load
to have wet spots at the end of the cycle.
NOTE: Using steam on overly damp items may result in
load not completely drying.
Selections
The following selections can be used to modify the currently
chosen cycle. The default selections will be lit after choosing a
cycle.
Temp
Press the Temp keypad to change the cycle's temperature on
Manual Cycles, Pet Items, and Steam Refresh. Choose from
No Heat, Low, Medium, or High depending on fabric type.
NOTE: The No Heat cycle will take longer to dry items.
Dryness
Press the Dryness keypad to change the dryness level in an
Auto-Sensing cycle. Choose from Damp, Less Dry, Near Dry or
Dry.
Use Damp to leave load slightly damp for easier ironing.
Use Less Dry for lightweight items such as sheets and shirts.
Use Near Dry for normal loads.
Use Dry for heavy items such as blue jeans and blankets.
Over-drying can cause wrinkling, shrinking, excessive lint con-
ditions, and will use more energy than necessary. To increase
energy savings and to make sure loads are dried without over-
drying, set your Auto-Sensing loads on Near Dry or Less Dry. If
items are damp or over-dry at the end of a cycle, increase or
decrease the Dryness setting the next time these loads are
dried. Remember the settings that work best to get ideal dry-
ing results. To finish drying damp items, use Quick Dry and ad-
just the time as needed.
Options
The following options can be used to modify the currently
chosen cycle, adjust the signal volume, and save favorite cy-
cles.
Extended Tumble
The Extended Tumble option prevents wrinkling by tumbling
the clothes load after the end of the cycle every two minutes
for up to 60 minutes. The display will show the time remaining.
The Extended Tumble LED light will be lit during the Extended
Tumble portion of a cycle. The option will end if the door is
opened.
Extended Tumble can be used along with the Steam Boost and
Anti-Static options. Steam Boost runs first, followed by Anti-
Static and then Extended Tumble.
NOTE: The Steam Boost option is not available with the
ENERGY STAR
®
setting.
Steam Boost
Use to release wrinkles and soften fabrics. Available with Auto-
Sensing Heavy Duty, Regular, and Perm Press cycles as well as
Pet Items (Medium or High heat only). Dryness/Auto-Dryness
must be set to Near Dry or Dry. Cannot be used with EcoDry.
Steam Boost can be used along with the Anti-Static option.
Steam Boost runs before Anti-Static.
Operating Your Dryer
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 Part No. D518541ENR4
Loading ...
Loading ...
Loading ...