Loading ...
Loading ...
Loading ...
Avoidfire
hazardorelectricalshock•
Donotuseanadaptor
plugorextensioncordor
removegroundingprong
fromelectricalpower
cord.Failuretofollowthis
warningcancauseserious
injury,fireordeath•
14-30R
FUSED3gAMP
120/240VOR
12g/208VWALL
ELECTRICDRYERS:
Grounding type GASDRYERS:
wall receptacle
l
Follow fabric care label instructions.
Place smalt items in a mesh bag.
Fill 1/3 to 1/2 full.
Place the front bar under
the lip of the lint screen opening.
I any circumstances
c_t, remove,
or bypass
the grounding prong
_rom this plug, J
Power supply
DRYER SERVICE cord with 3-prong
grounding plug
CORRECT Use this way ONLY
Drying Procedures
. Follow the guidelines below for preparing the load for drying.
Note: The instructions
appearing in this Use and
Care Guide are not meant to
cover every possibte condition
and situation that may occur.
Common sense and caution
must be practiced when
installing, operating and
maintaining any appliance.
. Read the Operating _nstructions for operating your specific modet.
. Always read and follow fabric care _abe_s and laundry product _abe_s.
_[_To reduce the risk of fire, electrical shock, or injury to persons, read Important
Safety Instructions before operating this dryer•
Prepare items for drying.
Dry items of similar fabric, weight and construction in the same toad.
Separate dark items from light-colored items. Separate items that shed tint from those
that attract lint. If an item sheds tint, turn it inside out.
Be sure bucktes, buttons and trim are heatproof and won't damage the drum finish.
Close zippers, fasten hooks and Velcro®qike fasteners. Tie strings and sashes to
prevent snagging and tangling.
If possible, turn pockets inside out for even drying.
Check for stains which may not have been removed in washing. Dryer heat may
permanently set some stains• Repeat stain removal process before drying.
Place smalt items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
Load the dryer.
The average toad will filt the drum 1/3 to 1/2 full. Items need room to tumble freely for
even drying and tess wrinkling. Do not overload dryer.
When drying targe items, dry only 2 or 3 at a time. Flit out the toad with small and
medium sized items•
For delicate or very smalt loads, add 2 lint-free towels for better drying, tess wrinkling,
and to prevent grease stains caused by fabric softener sheets.
Do not overdry items. Overdrying can cause wrinkling, shrinkage, harshness, and a
build-up of static electricity, which can produce more lint.
If desired, add a dryer fabric soffener sheet.
4. Close the dryer door and select the cyc{e, temperature, dryness _eve{ and options
desired. See Operating instructions for your specific model information.
5. Press START to begin the cycle.
To add or remove items when the dryer is running open the door• The dryer wilt stop
when the door is opened. Allow the drum to come to a compIete stop before
reaching inside.
Close the door and press Start to resume the cycle.
6. When the cycle ends, remove items immediately and hang or fo_d.
Features
End of Cycte Signal
A signal will sound at the end of the cycle and periodically during Extended Tumble at the
volume level selected. (some models)
Drum Light (some mode_s)
A drum light will come on whenever the door is opened to illuminate the dryer drum during
loading and unloading• Closing the door turns off the light.
Reversible Dryer Door
Your dryer _s equipped with a reversible door. The door can be hinged on the right or left side•
Refer to the INSTALLATION INSTRUCTIONS for directions on changing the door.
Drying Rack (some models}
Use the drying rack to dry items which shoutd not be tumble dried.
1. Open the dryer door and remove the tint screen.
2. Insert drying rack into the dryer drum• Place the front bar under the lip of the lint screen
opening.
3. Place items to be dried on top of the rack. Weight should not exceed 10 Ibs. Leave space
between items, but do not let items hang over the sides or through the grids. Do not
tumble other items when using the drying rack.
4. Select Timed Dry. Use only the Air Ftuff/No Neat option for items containing plastic, foam
rubber, rubber-like materials, feathers or down.
5. When items are dry, remove the rack and reptace the lint screen• If lint screen is not in
place, tumbling items could enter the exhaust system and cause damage to the dryer.
4
Loading ...
Loading ...