Loading ...
Loading ...
Loading ...
– 13 –
– 17 –
– 21 –
– 14 –
– 18 –
– 22 –
– 15 –
– 19 –
– 23 –
– 16 –
– 20 –
Specifications
Laser
Laser Type/Classification 670 nm visible, Class II
Self-Leveling Range ±11 arc minutes
Manual Leveling Method Three-screw leveling base with bull’s-
eye circular bubble and out-of-level
LED
Horizontal Accuracy ±10 arc seconds over temperature
<±1/16 in. per 100 ft (<±1.5 mm per
30 m)
Power Source 4 D-cell alkaline/NiMH/Ni-Cd (4.4 Ah)
batteries
Battery Life (68 ˚F / 20 ˚C) Alkaline/NiMH: 80 hours
Ni-Cd: 27 hours
Operating Diameter 1600 ft (500 m)
Operating Temperature –4 °F to 122 °F (–20 °C to 50 °C)
Troubleshooting
If none of the following techniques corrects the problem, take your
system to a local Trimble dealer or authorized service center for
evaluation or repair.
Problem Solution
Laser will not operate • Press power button.
• Check or replace batteries.
• Make sure the battery
contacts are clean.
• Make sure the battery housing
is securely in place.
• Return the laser to an
authorized service center for
inspection.
Laser out-of-level indicator
does not shut off
• Make sure the laser setup is
stable.
• Make sure the leveling screws
are free to turn.
• Re-level the laser and make
sure the bubble is centered in
bull’s-eye level vial.
• Return the laser to an
authorized service center for
inspection.
Laser not accurate • Check and adjust the laser’s
calibration as needed.
• Return the laser to an
authorized service center for
inspection.
Low-battery LED is flashing • Replace or recharge the
batteries.
The laser levels, the rotating
prism turns but the laser beam
does not come on
• Return the laser to an
authorized service center for
inspection
The receiver does not detect
the laser beam at long range
• Clean the lighthouse and
recheck the receiver distance.
• Return the laser to an
authorized service center for
inspection.
Batteries do not charge Make sure the laser is not
equipped with alkaline
batteries.
• Make sure the Ni-Cd batteries
are correctly installed.
• Replace the Ni-Cd batteries
with new ones.
• Replace the recharger.
Claim for Damage in Shipment
The LL500 laser system includes a laser, receiver, operator’s manual,
laser safety kit, carrying case, and alkaline batteries. Optional
accessories include various receivers and a battery recharger.
You should inspect your laser system as soon as you receive it. It has
been packaged for safe delivery. If it is damaged in any way,
immediately file a claim with the carrier or, if insured separately, with
the insurance company.
Safety Information
Included in this manual are CAUTIONS and Notes. Each of these
words represents a level of danger or concern.
A CAUTION indicates a hazard or unsafe practice that could result in
minor injury or property damage.
A Note indicates important information unrelated to safety.
Maintenance and Care
You will get years of service from the leveling system by following the
maintenance and care recommendations in this manual. Carry the
laser in its moisture-resistant, field-tested carrying case to safely
move the laser from one job to another.
However well the product is designed, mishaps do occur. The
most common problems associated with these are covered in the
following areas.
Storage
CAUTION: Do not store the laser in a wet carrying case. If the case
gets wet, open it and let it dry before storing the laser.
Battery Disposal
Some states and local areas have regulations regarding the disposal
of rechargeable batteries. Be sure that replaced batteries are
disposed of properly.
System Cleaning
Use only a good-quality glass cleaner and a soft cloth to clean all
external optical components. A dry cloth used on the laser exit
windows may scratch or damage the glass surfaces.
Monthly, wipe off with a moist, clean cloth any dust or dirt from the
laser’s outer surface, inside the battery housing, and within the
leveling base. Blow off any loose debris before cleaning any surfaces
to prevent scratching of optical surfaces.
Request for Service
Our goal is to provide prompt and efficient service through
competent service dealers.
Before returning your system for repair, be sure to do the following:
1. Put a note into the package identifying yourself as the owner.
2. Explain the operating difficulty.
3. Include a return address and phone number.
4. If the laser is in warranty, provide verification of the date of
purchase.
5. Pack the equipment securely for shipment in its original carrying
case.
6. Return the equipment prepaid and insured to your local dealer or
authorized Trimble Service Center.
7. Request estimate of charges for non-warranty or other service
work before repair begins. If estimates are not requested, repair
work will begin immediately.
All certified outlets have factory-trained personnel and use
authorized replacement parts to ensure proper and quick return. For
long-distance shipments, UPS, 2nd-Day Air, or airfreight is
recommended.
Except for one-way transportation charges, there will be no charge
for repairs caused by problems due to defective materials and/or
workmanship under warranty.
To locate your local dealer or authorized Trimble Service Center world
wide for service, accessories, or spare parts, contact one of our
offices listed below.
Laser Safety
This laser complies with all applicable portions of Title 21 of the code
of Federal Regulations, Department of Health and Human Services,
Food and Drug Administration (Federal Register, Volume 50, Number
161, August 20, 1985).
As with any visible laser device, the following safety rules should be
observed:
• Never look directly into a laser beam or point the beam into the
eyes of others. Set the laser at a height that prevents the beam
from shining directly into people’s eyes.
• Do not remove any warning signs from the laser.
• Use of this product by people other than those trained on this
product may result in exposure to hazardous laser light.
• If initial service is required, which results in the removal of the
outer protective cover, removal must only be performed by factory-
trained personnel.
Questions about laser safety should be addressed to:
Trimble Navigation Limited
5475 Kellenburger Road
Dayton, OH 45424-1099 U.S.A.
Attention: Quality Assurance Group, Laser Safety Officer
Labels
Labels required for this product:
EMC Declaration of Conformity
This laser has been tested and found to comply with the limits for
a Class B digital device for radio noise for digital apparatus set out
in the Radio Interference Regulations of the Canadian Department
of Communication, and is pursuant to part 15 of the Federal
Communication Commission (FCC) rules. These limits are designed
to provide reasonable protection against harmful interference in a
residential installation. This laser generates radio frequency. If it’s
not used in accordance with the instructions, it may cause harmful
interference to radio or television reception. Such interference can be
determined by turning the laser off and on. You are encouraged to try
eliminating the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the laser and the receiver.
For more information, consult your dealer or an experienced radio/
television technician.
CAUTION: Changes or modifications to the laser that are not
expressly approved by Trimble could void authority to use the
equipment.
Application of Council Directive(s): 89/336/EEC directive on EMC
Manufacturer’s Name: Trimble Navigation Limited
Manufacturer’s Address: 5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
European Representative Address: Trimble GmbH
Am Prime Parc 11
65479 Raunheim, Germany
Model Number(s): LL500
Conformance to Directive(s): EC Directive 89/336/EEC using
EN55022 and EN50082-1
Equipment Type/Environment: ITE/residential, commercial
& light industrial
Product Standards: Product meets the limit B
and methods of EN55022
Product meets the levels and
methods of IEC 801-2, 8 kV air, 4
kV contact IEC 801-3, 3 V/m 26
to 1000 MHz 80%, @ 1 kHz IEC
801-4, ac leads 2 kV
Warranty
Trimble warrants the LL500 laser to be free of defects in material and workmanship
for a period of five years. This warranty period is in effect from the date the system
is delivered by Trimble or its authorized Dealer to the purchaser, or is put into
service by a Dealer as a demonstrator or rental component.
Additionally, items covered by the standard Trimble one-year warranty are the
accessories. All other components not manufactured Trimble but sold as a part of
the system such as tripods and grade rods, will carry a 90-day warranty or the
manufacturer’s warranty, whichever is greater.
Trimble or its Authorized Service Center will repair or replace, at its option, any
defective part of components of which notice has been given during the warranty
period. Travel and per diem expenses, if required, to and from the place where
repairs are made will be charged to the purchaser at the prevailing rates.
Customers should send products to the nearest Authorized Factory Service Center
for warranty repairs, freight prepaid. In countries with Trimble Service Subsidiary
Centers, the repaired products will be returned to the customer, freight prepaid.
Any evidence of negligent, abnormal use, accident, or any attempt to repair
equipment by other than factory-authorized personnel Trimble certified or
recommended parts, automatically voids the warranty.
Special precautions have been taken to ensure the calibration of the laser; however,
calibration is not covered by this warranty. Maintenance of the calibration is the
responsibility of the user.
The foregoing states the entire liability of Trimble regarding the purchase and
use of its equipment. Trimble will not be held responsible for any consequential
loss or damage of any kind.
This warranty is in lieu of all other warranties, except as set forth above, including
an implied warranty mechantability of fitness for a particular purpose, is hereby
disclaimed. This warranty is in lieu of all other warranties, expressed or implied.
– 22 –
✔
N324
N324
Trimble Construction Division
5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
+1-937-245-5600 Phone
© 2002–2012, Trimble Navigation Limited. All rights reserved.
Reorder P/N 1044-0050 Rev. D (December 2012)
North America
Trimble Building Construction
Division
5475 Kellenburger Road
Dayton, Ohio 45424
U.S.A.
800-538-7800 (Toll Free)
+1-937-245-5587 Phone
+1-937-233-9441 Fax
Europe
Trimble GmbH
Am Prime Parc 11
65479 Raunheim
GERMANY
+49-6142-2100-0 Phone
+49-6142-2100-550 Fax
Africa & Middle East
Trimble Export Middle-East
P.O. Box 17760
Jebel Ali Free Zone, Dubai
UAE
+971-4-886-5410 Phone
+971-4-886-5411 Fax
Asia-Pacific
Trimble Navigation Singapore PTE Ltd.
80 Marine Parade Road, #22-06
Parkway Parade
Singapore, 449269
SINGAPORE
+65 6348 2212 Phone
+65 6348 2232 Fax
China
Trimble Beijing
20F, Central Tower, China Overseas
Plaza,
No.8 Yard, Guang Hua Dong Li
Chaoyang District, Beijing, PRC
CHINA 100020
+86-10-8857-7575 Phone
+86-10-8857-7161 Fax
www.trimble.com.cn
LASER LIGHT
DO NOT STARE INTO BEAM
CAUTION
Diode <3mW @ 635-670 nm
CLASS II LASER PRODUCT
5475 Kellenburger Rd.
Dayton, Ohio 45424-1099 U.S.A.
MFG.
S/N
MODEL:
✔
N324
COMPLIES WITH 21 CFR 1040 AS APPLICABLE
DANGER
LASER LIGHT
WHEN OPEN.
AVOID DIRECT
EYE EXPOSURE
www.trimble.com
Loading ...
Loading ...