Loading ...
Loading ...
Loading ...
49-1000361 Rev. 4 23
INSTALLATION INSTRUCTIONS
Installation Instructions
STEP 3 INSTALL WATER LINE
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i. (275-827 kPa).
5RXWH´2'FRSSHURU6PDUW&RQQHFW
™
plastic
tubing between house cold water line and the water
connection location.
• The tubing should
be long enough to
extend to the front of
the refrigerator. Allow
enough tubing to
accommodate the bend
leading into the water line connection.
NOTE: The only Café approved plastic tubing is
supplied in the SmartConnect
™
Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Other
types of plastic may crack or rupture with age and
cause water damage to your home.
SmartConnect
™
5HIULJHUDWRU7XELQJ.LWVDUHDYDLODEOH
in the following lengths:
2’ (.6 m) WX08X10002
8’ (2.4 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the
line of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits. Before purchasing, make
sure a saddle type valve complies with your local
plumbing codes.
STEP 1 REMOVE PACKAGING
WARNING
Tip Over Hazard.
The refrigerator is much heavier at the top than at the
bottom—be careful when moving. When using a hand
truck, handle from the side only.
• Carefully cut banding at the top and bottom, remove
the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE
CABINET DOWN IN ORDER TO REMOVE THE
6.,'
• The unit is secured to the skid with 4 slotted tie-
GRZQVWUDSV5HPRYHWKHVL[´EROWVIURPWKH
base channels in the tie-downs.
5HPRYHWKHVL[´EROWVVHFXULQJWKHVWUDSVWR
the skid.
NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF
6.,'
• The support blocks on the
bottom of the refrigeration
case must be removed
before the refrigerator
is taken off the skid
or damage will occur.
Carefully tilt the refrigerator
and slide the blocks out
from beneath.
• Remove the toekick and set
aside for final installation.
• Lift the refrigerator off the
skid with an appliance
dolly. Handle from the sides.
Remove
Tie Downs
Toekick
Floor
Cold Water Line
STEP 2 MOVE THE
REFRIGERATOR INTO THE HOUSE
• Re-use the corner posts from the packaging to
protect stainless steel models. Run the appliance
dolly straps over the posts and under the handles.
• Leave the protective film on the refrigerator until
installation is complete. IMPORTANT: Never lift the
refrigerator by the handle or push against the grille
SDQHOWKLVFRXOGFDXVHGDPDJHRUPLVDOLJQPHQW
• Avoid laying the unit on its back or side to prevent
sealed system restrictions.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
WARNING
Connect to potable water supply
only. A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 psi (275-827 kilopascals).
WARNING
ELECTRIC SHOCK HAZARD
Attach tubing clamp using existing hole only. DO
NOT drill into the refrigerator.
Loading ...
Loading ...
Loading ...