Loading ...
Loading ...
Loading ...
- 7 -
05/2020
Copyright © 2020, Fast ČR, a.s.
EN
Electric Sonic
Toothbrush
User'smanual
Prior to using this appliance, please read the user’smanual thoroughly,
even in cases, when one has already familiarised themselves with
previous use of similar types of appliances. Only use the appliance in the
manner described in this user’smanual. Keep this user’smanual in asafe
place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty
card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend
that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE TOOTHBRUSH AND ITS ACCESSORIES
A1 Toothbrush head*
A2 Ergonomically-shaped anti-slip
handle
A3 Button for turning the toothbrush
on and o and setting the
vibration speed (max. 41 000
vibrations per minute)
A4 LED indicator
signals the operation or charging
of the toothbrush
A5 Charging stand
A6 Power cord
A7 Travel case
*Note:
2 toothbrush heads are included.
ATTACHING AND REMOVING THE TOOTHBRUSH HEAD
Make sure that the toothbrush is turned o before attaching or removing
atoothbrush head A1.
Attach the toothbrush head A1 by sliding it on to the handle A2 from
above. Make sure that there is astrong connection of both parts.
Remove the toothbrush head A1 by pulling it o away from the handle
A2.
CHARGING THE TOOTHBRUSH
This toothbrush has a built-in Li-Ion battery that enables cordless
operation.
Make sure that the toothbrush is turned o before charging it.
Locate the charging stand A5 on an even and stable surface and plug
the power cord A6 into apower socket (100–240 V).
Put the toothbrush on to the stand A5 from above, see gure B. The LED
indicator A4 will be lit red. This signals the charging process. When the
battery is fully charged, the LED indicator A4 will be lit blue. After fully
charging, disconnect the charging stand A5 from the power socket.
Note:
Allow the toothbrush to charge for at least 15 hours before first use
and after not using it for along time.
If you are charging the toothbrush for the first time or if you have
not used it for along time, it may take up to 10 minutes before the
LED indicator A4 lights up.
A fully charged toothbrush will provide approximately 180 hours
of operation. If you brush your teeth twice a day for 2 minutes, the
toothbrush will last for 45 days without needing to be recharged.
HOW TO ACHIEVE THE LONGEST POSSIBLE BATTERY
LIFETIME
To ensure the longest possible lifetime of the battery, we recommend:
– Store, use and charge the battery at room temperature. Excessively
high temperatures may negatively aect its lifetime.
– do not unnecessarily leave the battery fully charged or completely
at for too long.
– do not keep the battery permanently fully charged.
– do not fully discharge the battery.
USING THE TOOTHBRUSH
Make sure that the toothbrush is properly assembled before using
it. Wet the toothbrush bristles and apply the toothpaste. Turn on the
toothbrush by pressing button A3.
1. CORRECT BRUSHING TECHNIQUE
We recommend to start by brushing the right half of the upper dental
arch from the outer side. When brushing, proceed from back to front.
Place the toothbrush bristles on to the teeth at an angle of 45° in line with
the gum, see gure C. Using short slow motions, move the toothbrush
to the other teeth. Once the outer side of the upper right dental arch
is brushed, move the toothbrush to the inner side of the dental arch.
Again, proceed from back to front. Adjust the toothbrush angle to the
tooth arrangement. When brushing the inner side of the front teeth of
the upper dental arch, hold the toothbrush handle A2 vertical so that
the tip of the toothbrush head A1 points upwards. Finally, brush the
upper tooth surfaces.
In the same way, brush the right half of the lower dental arch, the left
half of the lower dental arch and nally also the left half of the upper
dental arch. When brushing the inner side of the front teeth of the lower
dental arch, hold the toothbrush handle A2 vertical so that the tip of the
toothbrush head A1 points downwards.
2. SPEED SETTING
To increase the vibration speed, hold down button A3 for 3 seconds. This
can be done repeatedly until the desired speed is achieved. The change
in the speed setting is indicated by ashort ash of the LED indicator A4.
Another way to increase the speed is to hold down button A3 for
along time. The speed will increase gradually. The increasing speed is
indicated by the ashing LED indicator A4. When the maximum speed
level is achieved, the whole setting cycle will repeat from the beginning.
Release button A3 when the desired speed is achieved.
The set vibration speed is stored in memory.
Initially, until one becomes accustomed to the new way of brushing their
teeth, it is recommended to set alower speed.
3. 4PACER FUNCTION
The toothbrush has a timer function that momentarily pauses the
toothbrush every 30 seconds until it turns o automatically, thereby
informing the user that it is time to start brushing the next part of your
teeth. This will ensure that all the dental quadrants are brushed for the
same amount of time.
4. AUTOMATIC SHUT-OFF TIMER
The automatic shut-o timer automatically turns the toothbrush o after
2 minutes of operation. This is the tooth brushing time recommended by
dentists for the sonic toothbrush.
When you have nished using it, make sure that the toothbrush is
turned o and clean it according to the instructions contained in chapter
Cleaning and maintenance. Then put it back on to the charging stand A5
or into the case A7. Before putting it into the case A7, it is necessary to
remove the head A1 from the toothbrush handle A2.
CLEANING AND MAINTENANCE
For hygiene reasons, regularly clean the toothbrush after every use.
Make sure that the toothbrush turned o before cleaning it.
Thoroughly rinse the toothbrush head A1 under lukewarm running
water to remove any toothpaste or other remains. If whitening pastes
are used when brushing teeth, it is recommended to apply adrop of
soap on to the toothbrush head A1 and then thoroughly wash it under
running lukewarm water.
Rinse the toothbrush handle A2 under running lukewarm water and
then dry it.
In the event that the charging stand A5 is soiled, wipe it with aclean
dampened cloth and then wipe dry. Make sure that the plug on the
power cord A6 does not come into contact with water or moisture.
The travel case A7 may be wiped with adampened cloth or washed
under lukewarm running water. Then dry it thoroughly.
For cleaning, do not use abrasive cleaning products, thinners, etc.
Otherwise the surface of the appliance may be damaged.
REPLACING THE TOOTHBRUSH HEAD
Regularly replace the toothbrush head A1 every 3 months or sooner if it
shows signs of wear. Use only original replacement toothbrush heads.
Replacement toothbrush heads are available from you vendor both in
online and brick&mortar stores.
STORAGE
When not using the toothbrush for an extended period of time,
disconnect the charging stand A5 from the power socket and put the
toothbrush into the case A7.
Store the case A7 with the toothbrush and the charging stand A5 in
adry, clean place.
Loading ...