Loading ...
Loading ...
Loading ...
• 6 •
4. When the internal battery is fully
charged, the charger will automatically
go into maintain mode and maintain the
battery at full charge without damaging
it. When in maintain mode, the Battery
% LED will pulse, as long as there is an
AC cord connected to the charging port.
5. Charge the jump starter as soon as
possible after use.
CHARGING THE INTERNAL BATTERY
WHILE DRIVING
You may also charge the internal battery
while driving, using a 12V port charging
cable (part number 94500109 –
not included).
IMPORTANT: WHEN USING A 12V PORT
CHARGING CABLE, DO NOT CHARGE
INTERNAL BATTERY FOR MORE THAN
30 MINUTES OR LEAVE THE BATTERY
UNATTENDED. IT COULD EXPLODE,
CAUSING PROPERTY DAMAGE OR
PERSONAL INJURY.
1. Make sure the car is running.
2. Insert one end of the accessory cable
into the 12V DC power outlet.
3. Insert the other end of the accessory
cable into the vehicle’s accessory
outlet (lighter socket).
NOTE: The Battery % LED does not
operate during this method of charging.
Using this method to charge the battery
overrides the maintain mode and the
battery can be overcharged.
4. Monitor the progress of the charge by
pressing the Battery % button. When
the battery is fully charged, disconnect
the accessory cable from the Portable
Power, then from the lighter socket of
the vehicle.
NOTE: Completely disconnect the charger
cable when the engine is not running.
5. USING THE PORTABLE POWER
DIGITAL DISPLAY
To check the jump starter’s internal
battery status, press the Battery %
button. The display will show the percent
of charge of the internal battery.
When connected to the vehicle with the
Jump Start On/Off switch in the OFF
position, the display shows the vehicle’s
battery voltage. When connected and in
the ON position, the display shows the
equalized voltage between the vehicle’s
battery and internal battery.
JUMP STARTING A VEHICLE
IMPORTANT: Using the Jump Start
feature without a battery installed in
the vehicle will damage the vehicle’s
electrical system.
1. Turn the ignition OFF.
2. Lay the DC cables away from any
fan blades, belts, pulleys and other
moving parts.
3. For a negative-ground vehicle (as in
most vehicles), connect the portable
power’s POSITIVE (RED) clamp to
the POSITIVE (POS, P, +) battery
post. Next, connect the NEGATIVE
(BLACK) clamp to the vehicle chassis
or engine block, away from the battery.
4. For a positive-ground vehicle, connect
the portable power’s NEGATIVE
(BLACK) clamp to the NEGATIVE
(NEG, N, -) battery post. Next,
connect the POSITIVE (RED) clamp
to the vehicle chassis or engine block
away from the battery.
IMPORTANT: If you have connected the
clamps backwards, an audio alarm will
sound. DO NOT turn the On/Off switch to
the ON position. This could cause serious
damage to the jump starter or the vehicle.
Reverse the connections and the audio
alarm will stop.
5. Turn the switch to the ON position.
6. Crank the engine for no more than
8 seconds. If the engine does not start,
wait 2 minutes before cranking again.
7. After the engine starts, turn the switch
to the OFF position and remove the
portable power from the battery.
8. Charge the portable power.
USING THE WORK/EMERGENCY
FLEX LIGHT
1. Position the jump starter on a at, stable
surface near the intended work area.
2. Ensure that the battery clamps are
securely clipped on the storage holders.
3. Remove the exible work light from
the storage clip on the side of the unit.
Point the light in the desired direction.
NOTE: Do not use the ex light to lift the unit.
4. Press the light button once. The
jump starter light will turn on and
illuminate your work area.
5. Press the light button again. The light
will ash.
6. When nished, press the light button
again, to turn off the light.
7. Return the ex light to the storage clip
after use.
8. Charge the jump starter as soon as
possible after using the ex light.
NOTE: The ex light will automatically
shut off after 24 hours.
Loading ...
Loading ...
Loading ...