Loading ...
Loading ...
Loading ...
- 11 -
12/2020
Copyright © 2020, Fast ČR, a.s.
PREPARING THE ROBOTIC VACUUM CLEANER FOR OPERATION
INSTALLING AND USING THE SIDE ROTARY BRUSHES
■ The side rotary brushes A16 and A23 are intended for smooth floor surfaces and ensure effective cleaning in
corners, along walls and furniture.
■ Turn the vacuum cleaner upside down. Prepare the side rotary brushes A16 and A23. Gradually push both the
included side brushes precisely and with force on to the pins intended for them. While doing this, make sure
that the marks L and R both on the brushes and on the robotic vacuum cleaner match. Turn the robotic vacuum
cleaner back over to the operating position.
■ When using the robotic vacuum cleaner to clean rooms with carpets, remove the side rotary brushes A16 and
A23. When removing them, proceed in the reverse sequence to their installation.
INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL
■ Push down the latch of cover B10 on the rear side of the remote control B1 to release it and remove the cover.
■ Insert two type AAA (1.5 V) batteries into the remote control B1. When inserting the batteries, ensure the correct
polarity as shown inside the battery compartment B11. Put the cover B10 back on and click it into place.
■ In the event that the batteries are flat, replace them with new ones. Do not combine various types of batteries
or new and old batteries.
■ The signal range of the remote control B1 is approximately 6 m.
INSERTING AND REMOVING THE BATTERY
■ The robotic vacuum cleaner is equipped with a Li-ion battery C1. If the battery is packed separately, it is
necessary insert it into the robotic vacuum cleaner before first use. Use only the original battery type.
■ Turn the vacuum cleaner upside down. Check that switch A13 set to position 0 (off).
■ Screw out the screws from the cover A20 and remove the cover A20.
■ Connect the connector C2, which is located inside the battery compartment, to the battery connector C3. The
battery C1 can only be connected in one direction. Put the battery C1 into the battery compartment and close
the battery compartment with the cover A20. In the front part of the cover A20 there are tabs that must first
slide into the grooves in the battery compartment, and only then is it possible to close the cover A20 and attach
it by screwing in the screws. After attaching the cover A20, turn the robotic vacuum cleaner back over to the
operating position.
■ Remove the battery C1 in reverse sequence. Before removing the battery C1, always check that switch A13 is
set to position 0 (off).
■ When the robotic vacuum cleaner will not be used for an extended period of time, take out the battery C1 and
store it in adry, clean and cool place out of children'sreach.
LOCATION OF THE CHARGING BASE
■ Locate the charging base D1 against awall on ahard, even and dry surface within reach of apower socket. Make
sure that there are no stairs or obstacles within adistance of 1m on the left and right of the base and within
adistance of 2 m in front of the base, that would prevent the robotic vacuum cleaner from finding the charging
base D1 and docking successfully.
■ Insert the power adapter connector D6 into socket D2 of the charging base, and insert the power cord plug
into apower socket. Place the power cord in such away that it does not tangle into the cleaning brushes of
the robotic vacuum cleaner.
■ After connecting to apower socket, the indicator light D7 will be lit, indicating the connection of the charging
base to apower source.
■ In the event that the robotic vacuum cleaner is not used for an extended period of time, disconnect the charging
base D1 from the power socket and store it in adry, clean and cool place.
CHARGING FOR THE FIRST TIME
■ Before using the robotic vacuum cleaner for the first time, it is necessary to fully charge the battery C1 for
aperiod of at least 12 hours.
■ Check that the charging base D1 is correctly positioned and connected to apower socket according to chapter
Location of the charging base. Set the switch A13 on the robotic vacuum cleaner to position I(on). Grasp the
robotic vacuum cleaner and manually place it into the charging base so that the charging contacts A15 on the
underside of the robotic vacuum cleaner and the charging contacts D4 on the charging base are connected.
When the contacts are connected, the charging process will start.
■ The robotic vacuum cleaner can also be charged without using the charging base. Insert the power adapter
connector D6 into socket A5 of the vacuum cleaner, and insert the power cord plug into apower socket.
■ During the charging process, "11:11" is gradually displayed from left to right on the display A6.
■ When the battery is fully charged, the charging process will stop automatically. The display A6 will show the
message "FULL" (FULLY CHARGED).
■ The robotic vacuum cleaner is ready for use.
DEFINING THE VACUUMING AREA USING MAGNETIC TAPE
■ The robotic vacuum cleaner comes with amagnetic tape. It can be used to define the vacuuming area without
you having to close doors or place artificial obstacles in the path of the robot vacuum cleaner. The robotic
vacuum cleaner will recognise the magnetic tape and will not travel over it. It will start cleaning in another
direction.
■ Place the magnetic tape H1 before the place that the robotic vacuum cleaner should not clean, for example room
doorway, carpet, cables on the floor or astaircase with rounded corners, etc.
■ To help the tape adhere better, you can attach it to the perimeter using standard double-sided tape.
Note:
The magnetic tape must be put down prior to every cleaning session because the
robotic vacuum cleaner does not store the boundaries in memory.
OPERATING THE ROBOTIC VACUUM CLEANER
TURNING THE ROBOTIC VACUUM CLEANER ON AND OFF
■ Turn on the power supply to the robotic vacuum cleaner by setting switch A10 to position I(on).
■ When button A7 (ON/OFF) on the control panel or button B2 (ON/OFF) on the remote control is pressed, the
voice message "System rebooting, please wait" will be made and the digits 5555 to 1111 will gradually appear on
the display A6. After the reboot, the robotic vacuum cleaner will be set to the stand-by mode and all the available
symbols will appear on the display A6. The robotic vacuum cleaner is now ready for operation.
Note:
If the robotic vacuum cleaner is parked in the charging station D1 when turned off,
subsequently when switch A13 is set to position I(On), the voice message "Please turn
on the power switch" will be made and the error message E 2 will appear on the display
A6. Set switch A13 to position I(On) and the charging process will start automatically.
■ Setting switch A13 to position 0 (Off) will turn the robotic vacuum cleaner off. The display A6 will be turned off
completely. When the robotic vacuum cleaner is turned off, it does not react to any button on the control panel
A3 or on the remote control B1.
STAND-BY MODE
■ The stand-by mode means that the robotic vacuum cleaner is ready for use. The system time is shown on the
display A6 and the symbols of all the available functions are lit.
■ Set the robotic vacuum cleaner to the stand-by mode by pressing button A7 (ON/OFF) on the robotic vacuum
cleaner or buttons B2 (ON/OFF) on the remote control either by turning on the power supply using switch A13
or whenever while the robotic vacuum cleaner is running.
SLEEP MODE
■ The robotic vacuum cleaner will enter the sleep mode either automatically after ten minutes of inactivity or when
the control button A7 (ON/OFF) is pressed on the robotic vacuum cleaner for longer than 3 seconds. Abeep
is made, the display will turn off and the robotic vacuum cleaner automatically switches to the sleep mode.
■ To wake the robotic vacuum cleaner from the sleep mode to the stand-by mode, press button A7 (ON/OFF) on
the robotic vacuum cleaner or the control button B2 (O/OFF) on the remote control B1. When it is woken, abeep
is made and avoice message "System rebooting, please wait" is made.
SETTING THE SYSTEM TIME OF THE ROBOTIC VACUUM CLEANER
■ The system time is actually the current time. It must be correctly set if you wish to use the scheduled cleaning
function.
■ In the stand-by mode or in the charging mode in the base, press button A8 (PLAN) on the control panel A3. The
digits before the colon, representing the hours, will start flashing on the display A6.
■ Use button A12 (HOME) or A11 (MAX) to set the hours value. To speed up the setting process, hold down button
A12 or A11.
■ Press button A7 (ON/OFF) to confirm the set hours value. The digits after the colon, representing the minutes,
will start flashing.
■ Use button A12 (HOME) or A11 (MAX) to set the minutes value. To speed up the setting process, hold down
button A12 or A11.
■ Press button A7 (ON/OFF) to confirm the set hours value. The system time has now been set.
■ If you do not perform any change within 5 seconds, the system time setting mode will automatically be cancelled
and the previously set time will be shown on the display A6. The setting will not be stored in memory.
TURNING VOICE MESSAGES ON/OFF
■ If you prefer not to have the robotic vacuum cleaner make system voice messages, deactivate this function by
simultaneously pressing buttons A12 (HOME) and A8 (PLAN) on the control panel A3 of the robotic vacuum
cleaner. The robotic vacuum cleaner will only make beeps.
■ If you wish to reactivate the voice messages, again simultaneously press the buttons A12 (HOME) and A8 (PLAN).
SELECTING THE ROBOTIC VACUUM CLEANER CLEANING MODE
Tip:
During the first vacuum in anew environment, watch the movement of the robotic vacuum
cleaner. You can thereby recognise problematic obstacles and remove them for the next
cleaning session.
AUTOMATIC CLEANING MODE
■ Press button A7 (ON/OFF) on the robotic vacuum cleaner or B2 (ON/OFF) on the remote control. The robotic
vacuum cleaner will enter the automatic cleaning mode, in which it effectively combines various routes to
achieve an optimal clean of the entire floor area. As soon as the vacuum cleaner finish cleaning, it will seek out
the base and dock there to recharge.
ALONG-THE-WALLS CLEANING MODE
■ Press button A9 (EDGE CLEAN) on the control panel or press button B8 (MODE) on the remote control so that the
message mod1 appears on the display A6 and icon A9 (EDGE CLEAN) remains lit. The robotic vacuum cleaner
will enter the clean along the walls mode, in which it moves along the perimeter of the room and the motorised
side rotary brushes A16 and A23 sweep out the dirt along the walls, furniture and in corners to achieve aperfect
clean.
2x2 METRE AREA CLEANING MODE
■ Place the robotic vacuum cleaner approximately in the middle of the area that you wish to clean.
■ Keep pressing button B8 (MODE) on the remote control until mod2 appears on the display A6. The robotic
vacuum cleaner will enter the 2x2 metre area cleaning mode in which it will move in straight parallel lines and
vacuum an area of approximately 2x2 metres. As soon as the robotic vacuum cleaner finishes cleaning this area,
it will return back to the starting point and make avoice message "Cleaning complete".
RANDOM DIRECTION MOVEMENT MODE
■ Keep pressing button B8 (MODE) on the remote control until mod3 appears on the display A6. The robotic
vacuum cleaner will enter the random direction movement mode and will continue cleaning in this mode until
the battery C1 is almost flat. When the robotic vacuum cleaner detects alow battery voltage, it will stop cleaning
and make avoice message "Please Charge". Then it will seek out the charging base D1 and dock itself in order
to recharge.
INTENSIVE CLEANING MODE
■ Keep pressing button B8 (MODE) on the remote control until mod4 appears on the display A6. The robotic
vacuum cleaner will enter the intensive cleaning mode, where it will clean the same location at least twice. The
robotic vacuum cleaner continues cleaning until the battery C1 is almost flat. When the robotic vacuum cleaner
detects alow battery voltage, it will stop cleaning and make avoice message "Please Charge". Then it will seek
out the charging base D1 and dock itself in order to recharge.
Loading ...
Loading ...
Loading ...