Loading ...
Loading ...
Loading ...
9
• Press the DRIP COFFEE ON/OFF button (fig. 4).
The ON indicator light on the button comes on and
the appliance starts to make the coffee. (To make
the coffee at the programmed time, press the AUTO
button (fig. 3) and the AUTO light on the button
comes on.
• Delivery of coffee will start after a few seconds.
It is completely normal for the appliance to release a
little steam while the coffee is percolating.
To keep the coffee hot after percolation, place the
carafe on the hot plate and leave the appliance on
(drip coffee indicator on). The coffee in the carafe is
kept at the right temperature.
• To turn the appliance off, press the DRIP COFFEE
ON/OFF button.
HOW TO CHOOSE THE FLAVOR OF THE
DRIP COFFEE
With the AccuFlavor System, the flavor of the drip
coffee can be chosen according to personal taste. By
turning the AccuFlavor selector knob (fig. 12), the
coffee machine can be set for coffee with a strong
(STRONG position) or light (LIGHT position) taste.
The AccuFlavor Selector changes the strength of the
coffee.
HOW TO MAKE ESPRESSO
FILLING THE WATER TANK
Lift the cover and remove the water tank on the left (fig.
13) by pulling it upwards. Fill the tank with cold clean
water. Replace the tank, pressing lightly to open the
valve located on the bottom of the tank.
The tank can also be filled without removing it, pouring
the water directly from a carafe.
Note: Never use the appliance without water in the
tank. Always remember to add more water when the
level drops to less than an inch from the bottom.
PREHEATING THE COFFEE UNIT
To obtain espresso at the right temperature, the coffee
machine must be preheated. Turn the selector knob to
the position (fig. 14) at least half an hour before
making the espresso, making sure the filter holder is
attached to the appliance (check that the steam knob is
closed). To attach the filter holder, position it under the
boiler outlet with the handle towards the left (fig. 15),
push it upwards and at the same time rotate the handle
towards the right. Rotate firmly. Wait for half an hour,
then make the espresso as described in the following
chapter.
Alternatively, preheating can be achieved more rapidly
proceeding as follows:
1.Turn the appliance on by rotating the selector knob to
the position (fig. 14) and attach the filter holder
to the appliance without adding ground coffee.
2.Place a cup under the filter holder. Use the same cup
as will be used to prepare the coffee in order to
preheat it.
3.Wait for the OK indicator light to come on (fig. 16),
then immediately rotate the selector knob to the
position (fig. 17), run the water off until the OK
indicator light goes out, then interrupt delivery by
rotating the selector knob to the position (fig. 14).
4.Empty the cup. Wait until the OK indicator light
comes on again then repeat the same operation.
(It is normal for a small and harmless puff of steam to
be given off when removing the filter holder).
HOW TO PREPARE ESPRESSO USING THE FILTER
HOLDER FOR GROUND COFFEE
1.After preheating the appliance as described in the
paragraph above, place the ground coffee filter in
the filter holder, making sure the tab is correctly
inserted in the housing as shown in fig. 18.
2.To prepare a single espresso, fill the filter with a level
measure of ground coffee, about 7 grams (fig. 19).
To prepare two coffees, use the filter and fill with two
loosely filled measures of ground coffee (about 6+6
grams). Fill the filter a little at a time to prevent the
ground coffee from overflowing.
IMPORTANT: For correct operation, before adding the
ground coffee to the filter holder, clean the filter from
residues of ground coffee from the previous infusion.
Note: Use top quality fine-ground coffee for espresso
coffee machines.
3.Distribute the ground coffee evenly and press lightly
with the tamper (fig. 20).
Note: Correct pressing of the ground coffee is
essential to obtain a good espresso. If pressing is
excessive, coffee delivery will be slow and the froth
will be dark. If pressing is too light, coffee delivery
will be too rapid and the froth will be thin and light
colored.
4.Remove any excess coffee from the rim of the filter
holder and attach the filter holder to the appliance.
Rotate firmly (fig. 15) to avoid leaks of water.
5.Place the cup or cups (ideally preheated by rinsing
with a little hot water) under the filter holder spouts
(fig. 21).
6.Make sure the espresso OK indicator light (fig. 16) is
on (if off, wait until it comes on), then select (fig.
17) until the required quantity is obtained. To
interrupt, place the selector back in the position
(fig. 14).
Loading ...
Loading ...
Loading ...