Loading ...
Loading ...
Loading ...
DRAIN FROM
ICE MAKER
ICE MAKER
POWER CORD
DRAIN
TRAP
ACCESS PANEL
1-1/2” (3.8 cm) DRAIN PIPE
5/8” (.63 cm) I.D.
DRAIN TUBING
AND HOSE CLAMP
TUBING CLAMPS
VENT TUBE
SUPPLIED SCREWS
DISCHARGE TUBE GOES THROUGH
THIS OPENING IN THE ACCESS PANEL
ACCESS PANEL
DRAIN PUMP
DRAIN PUMP
POWER CORD
DRAIN FROM
ICE MAKER
VENT TUBE GOES THROUGH THIS
OPENING IN THE ACCESS PANEL
DRAIN PUMP’S DISCHARGE LINE
THROUGH THIS OPENING
Front
of Unit
Top of
Unit
6-3/4”
(17.1 cm)
4-1/16”
(10.3 cm)
2-3/8”
(6.0 cm)
14-3/4”
(37.5 cm)
24-5/8” (62.6 cm)
22” (55.9 cm)
13
DRAIN PLUMBING
Your ice machine uses a gravity drain that requires 5/8” (.63 cm) ID tubing from the back of the ice maker to a plumbed
connection to a sanitary sewer (see Gravity Drain drawing below). Remove the access panel, with a 5/16” (0.8 cm)
wrench to plumb in drain connection. Gravity drain location for built-in units can be within the area shown in illustration
below. An optional drain pump can be purchased for your ice machine if a gravity drain is not accessible. Observe
and follow all local codes when installing an ice machine.
GRAVITY
DRAIN
DRAIN PUMP
Model Number -
VUIM-DP
((SSoolldd sseeppaarraatteellyy -- sseeee
iinnssttaallllaattiioonn iinnssttrruuccttiioonnss
ssuupppplliieedd wwiitthh ddrraaiinn
ppuummpp))
GRAVITY DRAIN LOCATION
WARNING
Failure to use adequate drainage system will result in surrounding water damage and/or poor ice production.
REAR OF UNIT
GARDEN HOSE
FITTING
5/8” (.63 cm) I.D. DRAIN
TUBING BARB
*MAKE CERTAIN ALL HOSE
CLAMPS ARE SECURE
COMPRESSION FITTING
2-1/4” (5.7 cm)
5-1/2” (14.0 cm)
1/4” (.64 cm) TUBING FROM
COLD WATER LINE
12
Water Supply
• This ice machine must be connected to a potable, active cold water supply line delivering water pressure at a
minimum pressure of 20 psi and maximum of 120 psi.
• Water connection is made through a 1/4” (.64 cm) compression right angle garden hose fitting. DO NOT use any
thread sealers. NOTE: The water line fitting supplied with your ice machine is to be used on a 1/4” (.64 cm) copper
water supply line only. Do not attach a plastic supply line to your unit using this fitting.
• A water filter is recommended for this unit. A quality filter can remove particles as well as remove taste and odors
from water.
• Do not use a reverse osmosis water filtration system with the ice machine.
• Softened water is not recommended. This will produce mushy, cloudy ice cubes that will stick together.
• De-ionized water is not recommended. This water will not form solid ice cubes.
• A water specialist can recommend proper water treatment.
• After installation of water line, turn on water and check for any leaks. Additional tightening may be needed. DO NOT
use any type of thread sealer.
• Allow extra water line for easy removal of unit and to help prevent the water line from kinking.
WATER CONNECTION
Fitting
Valve
Adapter
Rubber
Washer
Compression Fitting
Compression Nut
1/4” (.64 cm) copper
water supply line
(supplied by customer)
From water supply
to ice machine
Loading ...
Loading ...
Loading ...