Loading ...
Loading ...
Loading ...
When operating unit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
• Wear eye protection and heavy clothing.
• Extend your left arm and hold handlebar
grip with your left hand.
• Hold throttle grip with your right hand with
finger on throttle trigger.
• Keep unit below waist level.
• Keep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
• Maintain full weight of tool on your left
shoulder.
• WithoL_ bending over, keep the blade or
trimmer head near and parallel to the ground
and not crowded into material being cut.
OPERATING INSTRUCTIONS FOR
USE WITH TRIMMER HEAD
_ WARNING: Always wear eye protec-
tion. Never lean over the trimmer head. Rocks
or debris can ricochet or be thrown into eyes
and face and cause blindness or other serious
injury.
Before trimming, bring engine to a speed suffi-
cient to cut material to be trimmed.
Do not run the engine at a higher speed than
necessary. The CL_ting line will CL_efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to "weld" onto the spool
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
• Release the throttle trigger.
• Move the ON/OFF switch to the ON posi-
tion.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.AIways keep
the shield in place when the tool is being oper-
ated.
To advance line:
• Operate the engine at full throttle.
• Hold the trimmer head parallel to and above
the grassy area.
• Tap the bottom of the trimmer head lightly on
the ground one time. Approximately 2 in. (5
cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer heed.if the line is worn down to 2
inches (5 cm) or less, more than one tap will
be required to obtain the most efficient line
length.
_WARNING: Useonly0.080"(2mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
CUTTING METHODS
_WARNING: Use minimumspeed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
• The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Lirte Crowded I,,l_
WOrkAres
Right W
• The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
• For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
• During light duty cutting.
• Near objects around which the line can
wrap such as small posts, trees or fence
wire.
• For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING - Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
Trimming
3 in. (8 cm)
Above Gro_lrl
SCALPING - The scalping technique removes
unwanted vegetation down to the ground. Hold
the bottom of the trimmer head about 3 in. (8
cm) above the ground and at an angle. Allow the
tip of the line to strike the ground around trees,
posts, monuments, etc. This technique in-
creases line wear.
9
Loading ...
Loading ...
Loading ...