Loading ...
Loading ...
Loading ...
The dispenser light Digital Status Display
When you use the dispenser, the lever will automatically turn the
light on. If you want the light to be on continuously, you may
choose either ON or AUTO.
ON AUTO
@
ON: Press the light bulb button at the right-hand side of the
dispenser control panel to turn the dispenser light on. The green
indicator will appear below ON.
AUTO: Press the light bulb button a second time to select the
Auto mode. The green indicator will appear below AUTO. The
dispenser light will automatically adjust to become brighter as the
room brightens, dimmer as the room darkens.
OFF: Press the light bulb button athird time to turn the dispenser
light off.
The dispenser lights are LEDs which should not need to be
changed. If it appears that your dispenser lights are not working,
check to be sure that the light sensor is not blocked (in Auto
mode). See "Troubleshooting" for more information.
A new water filter should display a reading of 99% and will
continue to decrease as the filter life is used. When display reads
10%, it is time to order a replacement filter. It is recommended
that you replace the base grille water filter cartridge when the
water filter indicator light changes to 0% OR when water flow to
your water dispenser or ice maker decreases noticeably. (See
"Changing the Base Grille Filter" later in this section.)
WA'I_RFILTER
PERCENTREMAINING
After changing the water filter cartridge, reset the water filter
status light by pressing and holding the RESET for 2 seconds.
The indicator light will change to 99% when the filter indicator is
reset.
Changing the Base Grille Filter
1. Locate the water filter cartridge cap in the front base grille.
Rotate the cap counterclockwise to a vertical position and
pull the cap and filter cartridge out through the base grille.
NOTE: There will be water in the cartridge. Some spilling may
occur,
The dispenser lock
Your dispenser can be turned off for easy cleaning or to prevent
accidental dispensing by small children and pets. To turn off the
dispenser, press and hold the lock button until the red indicator
appears below LOCKED. The ice and water dispensers will not
work. To unlock the dispenser, press the lock button until the
indicator disappears. Then continue to dispense ice or water as
usual.
2. Remove the cartridge cap by sliding it off the end of the old
cartridge. The cap will slide to the left or right. DO NOT
DISCARD THE CAR
3. Take the new cartridge out of its packaging and remove
protective cover from o-rings.
LOCKED
NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates
the dispenser levers.
4. Slide the cartridge cap onto the new cartridge. See
illustration in Step 2.
5. With cartridge cap in the vertical position, push the new filter
cartridge into the base grille until it stops. Rotate the cartridge
cap clockwise to a horizontal position. Flush the water
system (see "Flushing the Water System After Replacing
Filter" section).
I
The base grille water filter status light
The water filter status display or light will help you know when to
change your water filter cartridge. The display or light is located
at the top of the refrigerator compartment.
NOTE: Do not use with water that is miorobiologioally unsafe
or of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction may
be used on disinfected waters that may contain filterable
cysts.
Flushing the Water System After Replacing Filter
Use a sturdy container to depress the water dispenser bar until
the water begins to flow. Flush the water system by dispensing
and discarding 2 to 3 gallons (8 to 12 L) of water. Cleaning the
system will take approximately 6 to 7 minutes and will help clear
air from the line. Additional flushing may be required in some
households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
12
Loading ...
Loading ...
Loading ...