* depending on model Additional options can be set with the buttons `.
Express Wash/ Speed Perfect/ (VarioSpeed) *
This function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The change in the running time is indicated on the digital display 8. To obtain optimum cleaning results at a reduced running time, water and energy consumption are increased.
Half load *
If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. μ
SanitationPlus *
This function increases the temperatures and retains them for an extra long time to obtain a defined disinfection performance. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles.
Intensive zone *
Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly.
Shine & Dry *
By increasing the amount of water during the rinse cycle and extending the drying phase, stains are prevented and the drying result is improved. There is a slight increase in the energy consumption. Rinse aid is recommended for the Shine & Dry function (even when using combination detergents).
Energy Save *
Water and energy consumption can be reduced with the “Energy Save” function. The running time is extended for optimum cleaning and drying results.
Aqua sensorAqua sensor *
* depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling.
Zeolith drying
The appliance features a Zeolith container Zeolith is a mineral which can store moisture and heat energy and release them again. During the washing step this heat energy is used to dry the mineral and heat up the rinsing water. During the drying phase moisture from the washing compartment is stored in the mineral and heat energy is released. This released heat energy is blown into the washing compartment with dry air. This accelerates and improves drying. These processes therefore save a great deal of energy.
Caution Please ensure that the intake opening 1J is not obstructed and do not place any temperature-sensitive utensils in the lower basket at the rear right side above the blow opening 1R.
Warning – Risk of injury! Do not touch the blow opening 1R. The blow opening becomes hot and, furthermore, any damage will result in a chargeable callout by customer service.
Switching on the appliance
1. Turn on the tap fully.
2. Open the door.
3. Switch on ON/OFF switch. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display 8.
4. Press the START button h.
5. Close the door. The programme starts running.
Optical display while the programme is running *
* depending on model While the programme is running, an optical display is indicated on the floor under the appliance door. If the base panel is pulled forwards or if the appliance is installed at eyelevel with flush furniture front, the display is not visible.
Possible settings of the optical display:
To change the setting:
1. Open the door.
2. Switch on ON/OFF switch.
3. Hold down programme button # and press START button h until š:‹.... is indicated on the digital display.
4. Release both buttons.
5. Keep pressing programme button # until the previously set value, e.g. †:‹‚, is indicated on the digital display 8 †:‹... (for the optical display).
6. Keep pressing programme button 3 until the required value, e.g. †:‹ƒ, is indicated on the digital display 8.
7. Press START button h. The set value is saved.
8. Close the door.
Remaining running time display
When the programme is selected, the programme running time is indicated on the digital display 8. When the programme has started, the remaining running time is displayed on the floor (only for settings †:‹‚ and †:‹ƒ). The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
Timer programming
You can delay the start of the programme in 1 hour steps up to 24 hours.
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press the button X + until ‹‚ is flaching in the timer programming display P.
4. Press + or – button until the X displayed time corresponds with your requirements.
5. Press START button h, timer programming is activated.
6. To delete timer programming X, press the + or – button until ‹‹ is indicated on the digital display P. You can change your programme selection at any time until the programme starts.
7. Close the door.
End of programme
The end of the programme O / ‹:‹‹ is displayed on the floor – provided the optical display is switched on and is visible. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows:
1. Open the door.
2. Switch on ON/OFF switch.
3. Hold down programme button # and press START button h until š:‹.... is indicated on the digital display.
4. Release both buttons.
5. Press programme button # until the factory set value ›:‹ƒ is indicated on the digital display 8.
To change the setting:
1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off).
2. Press START button h, the set value is saved.
3. Close the door.
Note Depending on the setting for “Automatic switch off when programme ends or interior light”, the optical display is no longer or only briefly visible.
Reference file: Siemens SX66T093AU iQ700 Fully Integrated Dishwasher
Additionally, the document applies to other Siemens models: SN…, SX…
