Loading ...
Loading ...
Loading ...
17
Installation instructions for product with Hettich hinges
! It is recommended that this installation be performed by authorized technical stuff.
! Before installation, read the instructions carefully.
! Fit the refrigerator/freezer in stable kitchen units only.
! Cabinet dimensions are changed by material of trim ap
1
.
1. If material of trim ap
(1)
is plastic, look at (Table.1/B1) for cabinet dimensions.
2. If material of trim ap
(1)
is metal, look at (Table.1/B2) for cabinet dimensions.
! If necessary, reverse the door according to instructions.
1. See g.A for the necessary attachment components.
2. Open the package. Take gasket spacer
(9)
and brake into three as shown in gureD.
Themiddle part is door hang rail
(10)
. The other two parts are unit door spacers
(11)
. (g.D)
3. Insert trim ap
(1)
into slot and screw by screws
(8)
. (g.E)
4. Pass the power cord through ventilation shaft and position it so that the appliance could-
be easily plugged in once it has been installed. (g.B - g.C)
5. Cut trim gasket
(4)
to the height of the recess and stick it on reverse side of the doorhin-
ges of the appliance. (g.E)
6. Raise the appliance and slide into the kitchen unit.
7. Lean the appliance to the kitchen unit through the hinges and align the front feet with
frontsurface of the kitchen unit. (g.F)
8. Open the appliance door and screw the front feet by using screws
(7)
. (g.G)
9. Screw trim ap
(1)
to kitchen unit using screws
(7)
. (g.G)
10. Screw the hinges to the kitchen unit using screws
(7)
. (g.G)
11. Close the appliance door. Unscrew and remove the nuts
(14)
, washers
(13)
and adjustmen-
tbolts
(12)
from the appliance door. (g.H)
12. Remove the liner for the adhesive part on the door hang rails
(10)
. Place door hang
rails
(10)
on theappliance door by inserting the bosses on the holes of the appliance door,
aligning thefront surfaces of the door hang rails(
10)
and the appliance door parallel to
each other. Letthe door hang rails
(10)
, stick onto the appliance door. (g.H)
13. Slide the door hang
(2)
into door hang rails
(10)
. (g.J - g.K)
14. Take out the liners of the adhesive part on the front side of the door hang
(2)
.
15. Take out the liners of the adhesive part on the unit door spacers
(11)
and and stick them
onto theunit door(15), closer to the upper corners. (g.K)
16. Lean the unit door
(15)
to the door hang
(2)
, aligning the unit door spacers(11) on the
left,right and top edges with the sides of the unit or the doors of the nearer and upper
kitchenunits. (g.K)
17. Make sure that the unit door
(15)
sticks onto the door hang
(2)
. Pull the unit door
(15)
al-
lowing the door hang
(2)
to slide out the door hang rails
(10)
. Observe that the door hang
(2)
stays stuck on the unit door
(15)
. (g.L)
18. Lay down the unit door
(15)
on the oor and screw the door hang
(2)
to the unit door
(15)
by
screws
(7)
. (g.L)
19. To overcome some of the furniture mistakes, there are plastic spacers
(A)
sticked on the
door hang
(2)
. Remove these plastic spacers
(A)
. (g.M)
Loading ...
Loading ...
Loading ...