Loading ...
Loading ...
Loading ...
21
1. Turn the gas control/temperature knob counterclockwise to the "OFF" position. The status light
will stop blinking and stay on for a short time after the water heater is turned off. See Figure ‘A’.
TO TURN OFF GAS TO APPLIANCE
1. STOP! It is imperative that you read all safety warnings before lighting the pilot.
2. Turn the gas control/temperature knob counterclockwise to the "OFF" position.
3. Wait ten (10) minutes to clear out any gas. If you then smell gas, STOP! Follow “ B” in the safety
information above on this label. If you do not smell gas, go to the next step.
4. Turn the gas control/temperature knob clockwise to “PILOT”. See Figure ‘B’.
5. Press the gas control/temperature knob all the way in and hold it in. The knob should travel in about
6mm (1/4 inch) if it is set to "PILOT" correctly. While holding the gas control/temperature knob in,
click the igniter button continuously (about once a second) for up to 90 seconds or until Status Light
begins to blink.
6. When the status light starts blinking, release the gas control/temperature knob. Set the gas
control/temperature knob to the desired setting. See Figure ‘C’.
If the status light does not start blinking within 90 seconds, repeat steps 2 through 5 up to THREE (3)
times, waiting 10 minutes between lighting attempts.
The circuitry in this advanced gas valve requires that you wait 10 minutes between lighting attempts.
If the status light turns a solid color, release the gas control/temperature knob and repeat steps 2
through 5 (waiting 10 minutes before attempting to relight the pilot). If the status light does not start
blinking after three lighting attempts, turn the gas control/temperature knob to the "OFF" position
and call a qualified service technician or your gas supplier.
DANGER: Hotter water increases the risk of scald injury.
Consult the instruction manual before changing temperature.
Refer to the Lighting Instructions in the Installation Manual for more detailed troubleshooting
information.
DANGER:
LIGHTING INSTRUCTIONS
FIGURE 'D'
MAIN BURNER
THERMOPILE
PILOT
FIGURE 'A'
"OFF" POSITION
FIGURE 'B'
"PILOT" POSITION
FIGURE 'C'
"ON" POSITION
120°F
Mark
120°F
Mark
CONTROL KNOB
120°F
Mark
GAS CONTROL
Gas Control &
Temperature Knob
Status
Light
Igniter
A. This appliance has a pilot which is lit by a piezoelectric spark gas ignition system. Do not open the
inner door of the appliance and try to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
'RQRWWU\WROLJKWDQ\DSSOLDQFH
'RQRWWRXFKDQ\HOHFWULFVZLWFKGRQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ
,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPDQHLJKERUVSKRQH)ROORZWKHJDVVXSSOLHUVLQVWUXFWLRQV
,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHUFDOOWKHILUHGHSDUWPHQW
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not
SXVKLQRUWXUQE\KDQGGRQWWU\WRUHSDLULWFDOODTXDOLILHGVHUYLFHWHFKQLFLDQ)RUFHRUDWWHPSWHG
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately contact a qualified installer
or service agency to replace a flooded water heater. Do not attempt to repair the unit! It must be
replaced!
BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED
WITH WATER AND AIR PURGED FROM ALL LINES
WARNING: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
FOR YOUR SAFETY READ BEFORE LIGHTING
FLAMMABLE
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
Loading ...
Loading ...
Loading ...