Loading ...
Loading ...
Loading ...
Installation Using Your Dishwasher
Page 21Page 8
FORGET TO ADD A DISH?
A forgotten dish can be added at any time before the
detergent cup opens.
1. Press the Start/Pause button.
2. Open the door a little to stop the washing.
3. After the spray arms stop working, you can open
the door completely.
4. Load the forgotten dishes.
5. Close the door.
6. Press the Start/Pause button, the dishwasher will
start running again after 10 seconds.
WARNING! It is dangerous to open the door
when washing, because the hot water may
scald you.
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of
the dishwasher will sound for 8 seconds, then stop.
Turn off the appliance using the Power switch button,
shut off the water supply and open the door of the
dishwasher. Wait for a few minutes before unloading
the dishwasher to avoid handling the dishes and
utensils while they are still hot and more susceptible
to breakage. They will also dry better.
Switch off the Dishwasher
1. Switch off the dishwasher by pressing Power
button.
2. Turn off the water tap!
Open the door carefully
Hot dishes are sensitive to knocks. The dishes should
be allowed to cool down around 15 minutes before
removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a
few minutes before removing the dishes. Dishes will
be cooler and the drying will be improved.
Unloading the Dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one.
This will avoid water dripping from the upper Basket
onto the dishes in the lower one.
The program light is on but is not blinking, only in this
case the program has ended.
About the Safety Supply Hose
The safety supply hose consists of double walls. The
hose's system guarantees its intervention by blocking
the flow of water in case of the supply hose breaking
and when the air space between the supply hose itself
and the outer corrugated hose is full of water.
WARNING! In order to avoid water staying in the inlet
hose, please close the hydrant after using.
WARNING! A hose that attaches to a sink spray
can burst if it is installed on the same water line
as the dishwasher. If your sink has one, it is
recommended that the hose be disconnected
and the hole plugged.
How to disconnect the safety supply hose
1. Turn off the water.
2. Release the water pressure by depressing the
pressure release button. This relieves water
pressure and protects you, and the room, from
severe splashing.
3. Unscrew the safety supply hose from the faucet.
TURNING ON THE APPLIANCE
Starting a wash cycle:
1. Draw out the lower and upper basket, load the
dishes and push them back. It is recommended to
load the lower basket first, then the upper one (see
the section entitled “Loading the Dishwasher”).
2. Pour in the detergent (see Page 14).
3. Insert the plug into the socket. The power supply is
220-240 VAC / 50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water
supply is turned on to full pressure.
4. Close the door, press the ON/OFF button to switch
on the machine.
5. Press the program button to select your desired
program, when the program is selected, the
corresponding icon will light up, then press the
Start/Pause button, the program will begin.
NOTE: When you press the Start/Pause button to
pause during washing, the running indicator will stop
blinking and the dishwasher will sound every minute
unless you press the Start/Pause button to start.
CHANGE THE PROGRAM
Premise:
1. A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise,
the detergent may have already been released, and
the appliance may have already drained the wash
water.
2. Press the Start/Pause button, the machine will be in
standby mode, then press the program button
more than 3 seconds then you can change the
program to the desired cycle setting (see the
section entitled " Starting a wash cycle. . .").
NOTE:
If this is the case, the detergent dispenser must be
refilled (see the section entitled "Adding
Detergent").
If you open the door during a wash cycle ,
the machine will pause. The LED display will
stop blinking and the buzzer will sound every
minute until you close the door. After
you close the door, the machine will keep on
working after 10 seconds.
Positioning the Appliance
Position the appliance in the desired location. The
Ÿ
back should rest against the wall behind it, and the
sides, along the adjacent cabinets or walls. The
dishwasher is equipped with water supply and
drain hoses that can be positioned either to the
right or the left sides to facilitate proper installation.
WARNING! Where the dishwasher has ventilation
openings in the base, these openings must not be
obstructed by a carpet.
Levelling
Once the appliance is positioned for levelling, the
Ÿ
height of the dishwasher may be altered via
adjustment of the screwing level of the feet. In any
case, the appliance should not be inclined more
than 2 °.
Cold Water Connection
How to Connect the safety supply hose
The appliance must be connected to the water mains
using new hose-sets. The old hose-sets should not be
reused.
Water pressure must be between 0.04 MPa and
1 MPa. If the pressure is below the minimum, consult
our Service Department for advice.
If the water pipes are new or have not been used for an
extended period of time, let the water run to make sure
that the water is clear. This precaution is needed to
avoid the risk of the water inlet getting blocked and
damaging the appliance.
1. Pull the safety supply hose completely out from the
storage compartment located at the rear of
dishwasher.
2. Connect the cold water supply hose to a threaded
3/4(inch) connector and make sure that it is
fastened tightly in place.
3. Turn water fully on before starting the dishwasher.
Loading ...
Loading ...
Loading ...