Loading ...
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifi cations to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifi cations to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: [email protected]
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the
icon to open a dialogue box)
WiFi
®
is a registered trademark of Wi-Fi Alliance
®
.
specifi cations
De-rating of the dimmer is not required for reverse phase applications. For
forward phase applications in two-gang installations, de-rate incandescent,
halogen, or electronic low voltage (ELV) loads to 600 Watts; in three-gang or
greater installations, de-rate incandescent, halogen, or electronic low voltage
(ELV) loads to 600 Watts on the outer units and 500 Watts on the center units.
RATING CHART
Load Single-Gang Dual-Gang Three-Gang
Incandescent/Halogen/ELV (FWD) 700 W 600 W / 600 W 600 W/500 W/600 W
Incandescent/Halogen/ELV (REV) 450 W
CFL/LED/EFL (FWD) 450 W / 3.8 A
CFL/LED/EFL (REV) 250 W / 2.1 A
Magnetic Low Voltage (FWD) 500 VA
Legrand reserves the right to change specifi cations without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load types. For
loads that require reverse phase dimming, such as ELV loads, adjust the phase
using the app.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3030 07/19
getting to know your dimmer
Item Name Description
1 Paddle Switch
• Press the top of the paddle to turn light on.
Double-tap to raise the dimming percentage
to 100%.
• Press the bottom of paddle to turn light off.
2 LED Locator Light
• Indicates the current state of device. Refer to
“LED Locator Light Explanations” for detail.
3
Dimmer Paddle /
LED Light Level
• Controls and displays the dimming percentage.
• Press (+/-) to adjust light in 2% increments.
Hold (+/-) to adjust light in 20% increments.
4 Air Gap Switch
• Completely turns off the dimmer. Use when
changing light bulbs.
NOTE: Blinking white denotes device is updating
RESET TO FACTORY DEFAULT
Deleting a device from the app will reset it to factory defaults. To manually reset
the switch to factory defaults press and hold the dim button for 10 seconds until
you see the LED blink then release. The device will reset in about 20 seconds
after release.
LED LOCATOR LIGHT EXPLANATIONS
LED
Color
State of
Light
Explanation
Blinking
Amber
Device is attempting to
connect to the network.
Solid White
Device is connected to your
network and is switched off.
Blinking
Red
Warns of an overload or short
circuit while your device is on.
1
2
3
4