User Manual Maytag MAT14PDAWW1 commercial washer

Maytag MAT14PDAWW1 commercial washer - Use Manual - Use Guide PDF.
Documents: Go to donwload!
  • Owner's manual - (English)

User manual of Maytag MAT14PDAWW1 (28 pages)
file thumbnail

Table of Contents Table des matiéres

WASHER SAFETY wi 2 SECURITE DE LA LAVEUSE INSTALLATION REQUIREMENTS 0.cccccseesesteeesteeeneneneennaes 3 EXIGENCES D’INSTALLATION ..sscseseseeenteeeeseeeeneenenennaeee 16

Outillage et PIECES

Exigences dC’eMplaceMe

Specifications Slectriques ccccsccccsssscesesssseesssseesssseesssseeess 18 INSTALLATION INSTRUCTIONS. .cccccsteeseeeteesteeeeeeeeeeneenens 6 INSTRUCTIONS D’ INSTALLATION .ccceccceseteestteeeesteeenneenes 19

Enlever la sangle d'expédition ccccssesesseseesssteeessseeeeees 19

Level the WaSHNEP Réglage de l’aplomb de 1a laVeUSE ..cecsseesssseeeesssteeeeees 20

Complete Installation ELECTRONIC CONTROLS SETUP. u ..csccsssseeeseeseesseeeseneneneees 10 REGLAGE DE LA COMMANDE ELECTRONIQUE 004 23 WARRANTY GARANTIE

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER?” or “WARNING.” These words mean:

You can be killed or seriously injured if you don't immediately DANG ER follow instructions.

You can be killed or seriously injured if you don't follow y'\ WAR | fe instructions.

All safety messages will tell you what the potential hazard is. tell you how to reduce the chance of injury. and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire. electric shack. or injury to persons when using the washer. follow basic precautions.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Tools needed

Level

Utility knife

Scissors

8" or 10" adjustable wrench

Flat-blade screwdriver

Pliers

Bucket

Parts supplied

Remove parts bag from washer. Check that all parts were included.

1 hose clamp

2 inlet hoses

4 flat water hose washers

2 front-leveling legs with nuts

1 drain hose

IMPORTANT Do not install or store the washer where it will be exposed to the weather. Do not store or operate the washer in temperatures at or below 32°F (0°C). Some water can remain in

Proper installation is your responsibility.

You will need:

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 4 ft (1.2 m) of where

Hot and cold water faucets located within 4 ft (1.2 m) of the back of the washer. and provide water pressure of 10-100 psi (69-690 kPa). A pressure reduction valve should be used in

A level floor with a maximum slope of 1" (25 mm) under entire washer.

A sturdy floor to support the washer weight (washer. water. and load) of 315 Ibs (143 kgs).

A 12" (800 mm) minimum riser to provide an air cushion and prevent noise and damage to valves for a single washer

A floor drain should be provided under the bulkhead.

Prefabricated bulkheads with electrical outlets. water supply

NOTE: Front access to the pump area is available by removing

2 No. T20 TORX" security screws and then removing the front panel.

T @TORX isa registered trademark of Acument Intellectual Properties. LLC.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death.

IMPORTANT : The washer must be electrically grounded in accordance with local codes and ordinances or. in the absence of

Mm If codes permit and a separate ground wire is used. it is recommended that a qualified electrical installer determine

[email protected] Do not ground to a gas pipe.

[email protected] Do not have a fuse in the neutral or ground circuit.

A copy of the above code standards can be obtained from:

National Fire Protection Association One Batterymarch Park. Quincy. MA 02269

A120 volt. 60 Hz. AC only. 15- or 20-amp. fused electrical

3 prong grounding plug.

To minimize possible shock hazard. the cord must be plugged

Recommended Ground Method

The washer. when installed. must be electrically grounded in accordance with local codes. or in the absence of local codes.

GROUNDING INSTRUCTIONS

For a grounded. cord-connected washer: This washer must be grounded. In the event of a malfunction

WARNING: Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance — if it will not fit the outlet. have a proper outlet installed by a qualified electrician.

For a permanently connected washer: This washer must be connected to a grounded metal. permanent wiring system. or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

INSTALLATION INSTRUCTIONS

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

Proper connection of the drain hose avoids damage to your floor due to water leakage. Read and follow these instructions.

Remove tape that covers shipping strap. Pull to completely remove the shipping strap with 2 cotter pins from the inside of the washer.

A. Shipping tape

B. Shipping strap

Pull firmly to remove the end of shipping strap from the back

Save the shipping strap for later use.

Connect the inlet hoses to the washer

The washer must be connected to the water faucets using

A. Coupling

B. Washer

Attach hose to bottom inlet valve opening first.

A. Cold water inlet valve

B. Hot water inlet valve

Attach second hose to top inlet. Tighten couplings by hand; then use pliers to make an additional two-thirds turn.

NOTE: Inlet valve threads are plastic. Do not strip or cross thread.

Connect the drain hose

NOTE: Slide washer onto cardboard or hardboard before moving across floor.

Move washer close to final position.

Put “hook” end of drain hose into laundry tub or standpipe.

Estimate the length of drain hose needed when washer is in

NOTE: Do not force excess length of drain hose down the standpipe. This could cause siphoning.

Place the hose clamp over the washer drain connector. Push the drain hose onto the washer connector. Use pliers to open clamp and slide clamp over drain hose. Check for good fit.

Way’ ——__ "7 i

Measure and mark a point approximately 16” (406 mm) from

Check that hose is not twisted or kinked and is securely in place.

Put “hook” end of drain hose into standpipe. Tightly wrap the shipping strap around the standpipe. Push plug into the nearest hole in the shipping strap.

Connect the inlet hoses to the water faucets

Before attaching water inlet hoses. run water through both faucets into a bucket. This will get rid of particles in the water

Attach bottom hose (inlet marked “H”) to hot water faucet.

Tighten coupling to faucet by hand.

Attach top hose (inlet marked “C”) to cold water faucet.

Tighten coupling to faucet by hand.

Use pliers to make an additional two-thirds turn to each coupling.

Install the front leveling feet

Stack two corner posts on top of each other. Tilt washer backward and insert corner posts 3" (76 mm) in from one side

: va

Use the leveling legs and nuts from the parts package. Screw

A. 1/2" (13 mm)

B. Base

C. Nut

Insert legs into correct holes at each front corner of washer

Tilt washer backward and remove corner posts. Gently lower washer to floor.

Move washer to its permanent location. Remove cardboard or hardboard from under washer.

Level the washer

Tilt washer forward raising back legs 1" (25 mm) off of floor. to

Check levelness of the washer by placing a carpenter’s level

If washer is not level. adjust the front legs up or down. Make

When washer is level. use a wrench to turn the nuts on front

Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method.

Check to be sure all parts are now installed.

If there is an extra part. go back through the steps to see which step was skipped.

Turn on water faucets and check for leaks. Tighten couplings if there is leaking. Do not overtighten; this could cause damage to faucets.

Check to be sure you have all of your tools.

Check that the shipping strap was removed from the back of

Electrical Shock Hazard

Piug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death.

Plug power supply cord into a grounded 3 prong outlet.

NOTE: On some models. during factory testing. the timer is advanced partially into the cycle causing the start button to be depressed. Allow timer to advance to the end of the cycle.

When the cycle is complete. the timer will reset and the start button will return to the start position.

If the timer is not allowed

Operating Tips

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Fire Hazard Replace all parts and panels before operating.

Never place items in the washer that are dampened

Failure to do so can result in death or electrical shock. with gasoline or other flammable fluids.

Checklist for washer operation: No washer can completely remove oil.

Check the following if the washer is not operating properly:

Power supply cord is plugged in.

Circuit breaker is not tripped or fuse is not blown.

Timer has been advanced to start of a cycle.

Water faucets are turned on.

Do not dry anything that has ever had any type of oil on

Doing so can result in death. explosion. or fire.

It is recommended that fiberglass items not be washed in coin operated washers.

If these items are washed in the washer. run

Inlet and drain hoses are not kinked.

Washer lid is closed.

Inlet valve is not frozen if not protected from the weather.

Suds level. Excess suds will slow the spin and cause poor

SPNOaRON

Typical full load sizes

Mixed Load{3 double sheets Heavy Work] pair pants

If you need assistance: 4 pillowcases Clothes 3 shirts Contact your authorized Maytag Commercial Laundry 6 pair shorts 1 coverall distributor. To locate your authorized Maytag Commercial 8 T-shirts 4 pair jeans Laundry distributor. or for web inquiries. visit 2 shirts 1 overall www.MaytagCommercialLaundry.com.

2 blouses

Just dial 1-800 NO BELTS (1-800-662-3587)—the call is free.

1 dress 4 tops 1 blouse 4 dresses When you call. you will need the washer model number and serial 2 slacks number. Both numbers can be found on the serial-rating plate 3 shirts located on your appliance.

2 pillowcases

Moving the Washer to a New Location

Place both rear leveling legs in the upper position and tape securely.

[email protected] Apply tape to the side and bottom of the cabinet near the

HM Open washer lid. wedge a blanket between the tub ring and

Rear legs

Front legs

Cnsnimnniemn TAPE 2 Sides

Handle washer gently. Do not drop washer while using hand

ELECTRONIC CONTROLS SETUP

BASIC OPERATION OF COMMERCIAL WASHER

+ For additional information. see www.MaytagCommercialLaundry.com.

WARNING

Electrical Shock Hazard Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

IMPORTANT

Electrostatic Discharge (ESD) Sensitive Electronics

ESD problems are present everywhere. ESD may damage

Touch your finger repeatedly to a green ground connection point

Blank Display

This condition indicate the washer is inoperative. Enter set-up mode

0 Minutes’ showing in display

This condition indicates the washer cannot be operated. Coins dropped or debit inputs during this condition will be stored in escrow but cannot be used until normal operation is restored by opening and closing the door.

If a door switch fails. it must be replaced before normal operation can be restored.

Cold Start (initial first use) Washer is programmed at the factory as follows:

+ 11 minute wash period

+ $0.00 wash price (PR models)

Warm Start (after power failure)

After a delay of up to 8 seconds. the washer is restored to the state that existed at time of the power failure.

Free Cycles

This is established by setting the cycle price to zero. When this happens. SELECT CYCLE’ will appear rather than a cycle price.

Debit Card Ready

This washer is debit card cable’ ready.

It will accept a variety

Display

After the washer has been installed and plugged in. the display will show O MINUTES’. Once the washer has been plugged in and the washer door opened and closed. the display will show the price. In washers set for free cycles. the display will flash “SELECT CYCLE’.

PERM.

DELICATES SMALL PRESS AND KNITS LOAD

WHITES.

COLORS BRIGHTS

PERM.

DELICATES SMALL PRESS AND KNITS LOAD

WHITES COLORS BRIGHTS

PERM.

DELICATES SMALL PRESS ANDKNITS LOAD

CONTROL SET-UP PROCEDURES CODE Bar

IMPORTANT: Read all instructions before operating.

A ii WASH LENGTH

The lower fabric setting key pads and the digital display are used al This is the number of minutes for WASH.

1. The LOWER LEFT key pad is used to adjust the values length of rinse agitation and the right digit is the number of rinses. associated with set-up codes. Pressing the key pad wil The number is changed in the following sequence (11. 21. 31. 41.

2. The LOWER MIDDLE key pad will advance you through the

3. The LOWER RIGHT key pad is used to select or deselect options.

This option is either SELECTED ON’ or NOT SELECTED OFF’.

Start Operating Set-Up FLU | Not Selected OFF’ arr tOND = PD Models: Insert access door key. turn. and lift to remove access door.

Sub.

Selected ON’ and not able to be deselected.

Unplug washer or disconnect power. to select ON’ and 3 consecutive times to remove

> Open console. disconnect plug on AA1. close console. (Not Selected OFF’.) Counter resets by going from OFF’ to ON’.

> Plug in wasner or reconnect power. ita Selected ON’ and not able to be deselected.

The washer is now in the set-up mode.

To select ON’ and not able to be deselected. first select ON’. then Before proceeding. it is worth noting that. despite ail of the options within two seconds press the LOWER RIGHT key pad twice. the available. an owner can simply choose to uncrate a new commercial LOWER LEFT key pad once. and exit the set-up mode. washer. hook it up. plug it in. and have a unit that operates. ~» Press the LOWER MIDDLE key pad once to advance to next code. c.Uf | SPECIAL PRICING OPTION SET-UP CODES This option is either SELECTED ON’ or NOT SELECTED OFF’.

The LOWER MIDDLE key pad will advance from code to code. c.7i}__|Not Selected OFF’

If SPECIAL PRICING OPTION is selected. you have access to codes 3? through 9’.

~» Press the LOWER MIDDLE key pad once to advance to next code.

FOR PR MODELS: The set-up codes are the same as for the PD’ models except where noted.

The set-up code is indicated by the one or two left-hand characters. The

(See VALUE OF COIN 1.) Advance from 0-39 by pressing the LOWER ees LEFT key pad. Factory preset for 7 quarters = $1.75.

PR MODELS ONLY: Factory preset for 0 quarters.

PR MODELS ONLY: Factory preset for 0 quarters. ~> Press the LOWER MIDDLE key pad once to advance to next code.

~» Press the LOWER MIDDLE key pad once to advance to next code.

COIN/DEBIT OPTION

Both coin & debit selected.

Coins selected. debit disabled. Press the LOWER RIGHT key pad

Debit Card selected. coins disabled. Press the LOWER RIGHT key

Enhanced Debit is self-selected when a Generation 2 card reader

~» Press the LOWER MIDDLE key pad once to advance to next code.

PRICE SUPPRESSION OPTION

This option causes the customer display to show ADD’ or AVAILABLE’ rather than the amount of money to add. (Used mainly in cebit installations.)

Not Selected OFF’.

Selected ON’. Press the LOWER RIGHT key pad once

~» Press the LOWER MIDDLE key pad once to advance to next code.

CLEAR ESCROW OPTION When selected. money held in escrow for 30 minutes without

Selected ON’.

Not selected OFF’. Press the LOWER RIGHT key pad once to deselect]

~» Press the LOWER MIDDLE key pad once to advance to next code.

PENNY INCREMENT OFFSET

This represents the penny increment price offset used in Generation 2 (Enhanced Debit) PR models. Choose from 0-4 pennies by pressing the LOWER LEFT key pad.

~» Press the LOWER MIDDLE key pad once to advance to next code.

If cycle counter (90C) is selected. the following is true:

Represents the number of cycles in HUNDREDS.

1 02 = 200

Represents the number of cycles in ONES.

225=

TOTAL CYCLES = 225

This is “VIEW ONLY” and cannot be cleared.

Press the LOWER MIDDLE key pad once to advance

If money counter (1.0C or 1.C0) is selected. the following is true:

Number of dollars in HUNDREDS.

3 01 = $100.00

Number of dollars in ONES.

468=$ 68.00

Number of CENTS.

575=$

TOTAL = $168.75

END OF SET-UP PROCEDURES

EXIT FROM SET-UP MODE

~» Unpiug washer or disconnect power.

~» Open console. reinsert plug into AA1. close console.

~» Plug in washer or reconnect power.

MAYTAG COMMERCIAL SINGLE-LOAD AND VENDED MULTI-LOAD WASHER AND DRYER WARRANTY

LIMITED WARRANTY ON PARTS

For the first five years from the date of purchase. when this commercial appliance is installed. maintained and operated according to the instructions attached to or furnished with the product. Maytag brand of Whirlpool Corporation (thereafter “Maytag”) will pay for factory specified parts or original equipment manufacturer parts to correct defects in materials or workmanship. Proof of original purchase date

ITEMS MAYTAG WILL NOT PAY FOR

All other costs including labor. transportation. or custom duties.

Service calls to correct the installation of your commercial appliance. to instruct you how to use your commercial appliance. to replace or repair fuses. or to correct external wiring or plumbing.

Repairs when your commercial appliance is used for other than normal. commercial use.

Damage resulting from improper handling of product during delivery. theft. accident. alteration. misuse. abuse. fire. flood. acts of God. improper installation. installation not in accordance with local electrical or plumbing codes. or use of products not approved by Maytag.

Pickup and Delivery. This commercial appliance is designed to be repaired on location.

Repairs to parts or systems resulting from unauthorized modifications made to the commercial appliance.

The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.

Chemical damage is excluded from all warranty coverage.

Changes to the building. room. or location needed in order to make the commercial appliance operate correctly.

10. Repairs made by a non-Whirlpool authorized service technician.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATIONS OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES. INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS. SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS. WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.

If you need service. please contact your authorized Maytag Commercial Laundry distributor. To locate your authorized Maytag Commercial Laundry distributor. or for web inquiries. visit www.MaytagCommercialLaundry.com.

3/10

For written correspondence:

Maytag Commercial Laundry Service Department 2000 M-63 North Benton Harbor. Michigan 49022 USA



Newest Added: MEW9530AB01 MGC4430BDB12 MTF2195AEB MDG6800AWQ MEDB766FW0

Maytag MAT14PDAWW1 | Pages: 28 | File type: PDF | Filename: 71680802_mat14pdaww1.pdf | Size: 2.9 MB | Language: English

Download User Manual

Contact us

Maytag in United States

1-800-344-1274 Hours of Operation Mon-Fri: 8 a.m. - 8 p.m. EST