User Manual Maytag MDE18MNAZW0 electric commercial dryer

Maytag MDE18MNAZW0 electric commercial dryer - Use Manual - Use Guide PDF.
Documents: Go to donwload!
  • Owner's manual - (English)

User manual of Maytag MDE18MNAZW0 (60 pages)
file thumbnail

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER?” or “WARNING.” These words mean:

Wt You can be killed or seriously injured if you don't immediately DANGER follow instructions.

You can be killed or seriously injured if you don't follow WARNING instructions.

All safety messages will tell you what the potential hazard is. tell you how to reduce the chance of injury. and tell you what can happen if the instructions are not followed.

WARNING = “Risk of Fire”

Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. If flexible metal duct is installed. it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse. be easily crushed. and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

To reduce the risk of severe injury or death. follow all installation instructions.

Save these instructions.

Post the following warning in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING: For your safety. the information in this manual must be followed to minimize the risk of fire or explosion. or to prevent property damage. personal injury. or death.

~ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

~ WHAT TO DO IF YOU SMELL GAS:

~ Installation and service must be performed by a qualified installer. service agency. or the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information. contact your gas supplier.

If a gas leak is detected. follow the “What to do if you smell gas” instructions.

In ihe State of Massachusetts. the following installation instructions apply:

+ Installations and repairs must be performed by a qualified or licensed contractor. plumber. or gasfitter qualified or licensed by

If using a ball valve. it shall be a T-handle type.

+ A flexible gas connector. when used. must not exceed 3 feet.

IMPORTANT: The gas installation must conform with local codes. or in the absence of local codes. with the National Fuel Gas Code. ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code. CSA B149.1.

The dryer must be electrically grounded in accordance with local codes. or in the absence of local codes. with the National Electrical Code. ANSI/NFPA 70 or Canadian Electrical Code. CSA C22.1.

IMPORTANT: When discarding or storing your old clothes dryer. remove the door.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire. electric shock. or injury to persons when using the dryer. follow basic precautions. including the following:

Read all instructions before using the dryer.

This dryer is intended only for drying clothes and textiles that have been washed in water. Do not use for any other purpose.

WARNING: If you smell gas. do not use the dryer or any electrical equipment nearby. Warn other people to clear the area. Contact the dryer owner immediately.

Do not place items exposed to cooking oils in your dryer. ltems contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

Do not dry articles that have been previously cleaned in. washed in. soaked in. or spotted with gasoline. dry-cleaning solvents. other flammable. or explosive substances as they give off vapors that could ignite or explode.

Do not dry unwashed items in the dryer.

Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

Before the dryer is removed from service or discarded. remove the door to the dryer compartment.

Do not reach into the dryer if the drum is moving.

Do not open door while dryer is in operation.

It will stop.

Do not install or store the dryer where it will be exposed to the weather.

Do not tamper with controls.

Clean dryer lint screen before or after each load.

Do not use this dryer without the lint screen in place.

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Installation Instructions or in published user-repair instructions that you understand and have the skills to carry out.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

The final part of a tumble dryer cycle occurs without heat (cool-down cycle) to ensure that the articles are left at a temperature that ensures that the items will not be damaged.

WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. (Avoids risk of spontaneous combustion).

Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint. dust. and dirt.

The interior of the dryer and dryer exhaust vent should be cleaned periodically by qualified service personnel.

See “Electrical Requirements” section for grounding instructions.

SAVE THESE INSTRUCTIONS

GAS DRYER INSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors. such as gasoline. away from dryer.

Do not install in a garage.

Failure to do so can result in death. explosion. or fire.

Your dryer can be installed in a basement. laundry room. or recessed area.

Companion appliance location requirements should also be considered.

IMPORTANT: Do not install or store the dryer where it will be exposed to the weather. Proper installation is your responsibility.

You will need:

A grounded electrical outlet located within 6 ft. (1.8 m) of where the power cord is attached to the back of the dryer.

See “Electrical Requirements”

+ A level floor with a maximum slope of 1" (25 mm) under entire dryer. Installing the dryer on soft floor surfaces. such as carpets

Gas dryer installation clearances

The location must be large enough to allow the dryer door

Additional spacing should be considered for ease of installation and servicing. The door opens more than 180°.

Additional clearances might be required for wall. door. and floor moldings.

Additional spacing of 1" (25 mm) on all sides of the dryer

When installing a gas dryer: IMPORTANT: Observe all governing codes and ordinances.

Check code requirements: Some codes limit or do not permit installation of clothes dryers in garages. closets.

Make sure that lower edges of the cabinet. plus the back and bottom sides of the dryer. are free of obstructions to permit adequate clearance of air openings for combustion air. See “Recessed Area and Closet Installation Instructions” below for minimum spacing requirements.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For recessed area and closet installations. minimum clearances can be found on the warning label on the rear of the dryer

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation. servicing. and compliance with local codes and ordinances.

If closet door is installed. the minimum unobstructed air opening in the top and bottom is required. Louvered doors with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same closet as the dryer.

48 in

(31 QO cm?) gn

(76 mm)

Front Closet View Door

(7 6 mm)

24 in? (155 cm?)

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death.

A copy of the above code standards can be obtained from:

National Fire Protection Association One Batterymarch Park. Quincy. MA 02269

CSA International 8501 East Pleasant Valley Road Cleveland. Ohio 44131-5575

Do not ground to a gas pipe.

Do not have a fuse in the neutral or ground circuit.

This dryer is equipped with a power supply cord having a 3-prong grounding plug.

To minimize the possibility of shock. the cord must be plugged

Check with a qualified electrician if you are not sure the dryer is properly grounded.

Gas Dryer Grounding

GROUNDING INSTRUCTIONS

+ For a grounded. cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown. grounding will reduce the risk of electric shock

+ For a permanently connected dryer: This dryer must be connected to a grounded metal. permanent wiring system. or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

SAVE THESE INSTRUCTIONS

Gas Supply

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Securely tighten all gas connections.

Examples of a qualified person include:

Failure to do so can result in death. explosion. or fire.

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes. installation must conform with American National Standard. National Fuel Gas Code ANSI 2223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association One Batterymarch Park. Quincy. MA 02269

CSA International 8501 East Pleasant Valley Road Cleveland. Ohio 44131-5575

The design of this dryer has been certified by CSA International

When installed above 10. 00 feet (3048 m). a four percent (4%) reduction of the burner B.T.U. rating shown on the model/serial plate is required for each 1. 00 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing above 10. 00 feet (3048 m) elevation. contact your local service company.

ELECTRIC DRYER INSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors. such as gasoline. away from dryer.

Do not install in a garage.

Failure to do so can result in death. explosion. or fire.

Your dryer can be installed in a basement. laundry room. or recessed area.

Companion appliance location requirements should also be considered.

IMPORTANT: Do not install or store the dryer where it will be exposed to the weather. Proper installation is your responsibility.

You will need:

A grounded electrical outlet located within 6 ft. (1.8 m) of where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

A level floor with a maximum slope of 1" (25 mm) under entire dryer. Installing the dryer on soft floor surfaces. such as carpets

Electric dryer installation clearances

The location must be large enough to allow the dryer door to be

Additional spacing should be considered for ease of installation and servicing. The door opens more than 180°.

Additional clearances might be required for wall. door. and floor moldings.

Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For recessed area and closet installations. minimum clearances can be found on the warning label on the rear of the dryer

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation. servicing. and compliance with local codes and ordinances.

If closet door is installed. the minimum unobstructed air opening in the top and bottom is required. Louvered doors with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

WARNING

48 in (310 cr’)

(76 mm)

Front Closet View Door

(76 mm)

24 in? (155 crm?)

Electrical Requirements — U.S.A. only

It is your responsibility:

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the National Electrical Code. ANSI/NFPA 70-latest edition and ail local codes and ordinances.

The National Electrical Code requires a 4-wire power supply connection for homes built after 1996. dryer circuits involved

A copy of the above code standards can be obtained from: National Fire Protection Association. One Batterymarch Park.

Quincy. MA 02269.

Do not use an extension cord.

If codes permit and a separate ground wire is used. it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Requirements — U.S.A. only (cont.)

Electrical Connection

To properly install your dryer. you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer.

If the dryer is installed with a 4-wire electrical supply connection. the neutral ground conductor must be removed from the external ground connector (green screw). and secured under the neutral terminal (center or white wire)

If local codes do not permit the connection of a neutral ground wire to the neutral wire. see “Optional 3-wire connection” section.

Electric Dryer Grounding

+ For a grounded. cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown. grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

+ For a permanently connected dryer: This dryer must be connected to a grounded metal. permanent wiring system. or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

SAVE THESE INSTRUCTIONS

Electric Dryer Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center terminal.

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death. fire. or electrical shock.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord. rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminalis or “U” shaped spade terminals with upturned ends.

A UL listed strain relief.

If your outlet looks like this:

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord. at least 4 ft. (1.22 m) long. must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire A-Wire (ground conductor) may be either green or bare.

Receptacle The neutral conductor must be identified by a white (14-30R) cover.

If your outlet looks like this:

Then choose a 3-wire power supply cord with ring

3-Wire Receptacle (10-30R)

Direct Wire

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center terminal.

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death. fire. or electrical shock.

Electrical Requirements - Canada only

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

Flexible armored cable or nonmetallic sheathed copper cable (with ground wire). covered with flexible metallic conduit.

All current-carrying wires must be insulated.

10-gauge solid copper wire (do not use aluminum).

Atleast 5 ft. (1.52 m) long.

WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility:

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code. C22.1 — latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association.

178 Rexdale Blvd. Toronto. ON M9W 1R3 CANADA.

To supply the required 4 wire. single phase. 120/240 volt.

60 Hz. AC only electrical supply on a separate 30-amp circuit. fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch

This dryer is equipped with a CSA International Certified Power Cord intended to be plugged

4-Wire Receptacle (14-30R)

Do not use an extension cord.

If you are using a replacement power supply cord. it is recommended that you use Power Supply Cord Replacement Part Number 9831317. For further information. please reference the service numbers located in the “Assistance or Service” section.

+ For a grounded. cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown. grounding will reduce the risk of electric shock

WARNING: improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

SAVE THESE INSTRUCTIONS

DRYER VENTING REQUIREMENTS

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

WARNING: To reduce the risk of fire. this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent. chimney.

(102 mm)

4" (102 mm) Heavy. Metal Exhaust Vent

Only a 4” (102 mm) heavy. metal exhaust vent and clamps may be used.

Do not use plastic or metal foil vent.

Rigid metal vent:

Flexible metal vent: (Acceptable only if accessible to clean)

Must be fully extended and supported in final dryer location.

Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance.

Do not install in enclosed walls. ceilings. or floors.

The total length should not exceed 7% ft. (2.4 m).

NOTE: If using an existing vent system. clean lint from entire length

Elbows:

45° elbows provide better airflow than 90° elbows.

Clamps:

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws

+ Moisture damage to woodwork. furniture. paint. wallpaper. carpets. etc.

+ Housecleaning problems and health problems.

12" min. (305 mm)*

24" min. (610 mm) ht

If main vent travels vertically through the roof. rather than through

+Minimum clearance above any accumulation of snow. ice. or debris such as leaves

The opening in wall or roof shall have a diameter 1/2" (13 mm) larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

A main vent can be used for venting a group of dryers. The main vent should be sized to remove 5663 I/min. (200 CFM) of air per dryer. Large-capacity lint screens of proper design may be used in main vent if checked and cleaned frequently. The room where the dryers are located should have make-up air equal to or greater than CFM of all the dryers in the room.

Back-draft dampers are available from your distributor and should be installed in the vent of each dryer to keep exhausted air from returning into dryers and to keep exhaust in balance within main vent. Unobstructed return air openings are required.

Although usually each single-load dryer should have an unobstructed outdoor air opening of 24 in.2 (154 cm?) (based on in.? [6.5 cm?] per 1. 00 Btu [252 kcal]). common make-up air openings are also acceptable. Set up common openings so the make-up air is distributed equally to all of the dryers. Keep

Each vent should enter the main vent at an angle pointing in the direction of the airflow. Vents entering from the opposite side should be staggered to reduce the exhausted air from interfering with the other vents.

30° max.

The maximum angle of each vent entering the main vent should be no more than 30°.

Keep air openings free of dry cleaning fluid fumes. Fumes create acids which. when drawn through the dryer heating units. can damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic cleaning of the vent system.

GAS SUPPLY CONNECTION

Make Gas Connection

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. Remove red cap from gas pipe on back of dryer.

2. Connect gas supply to dryer. Use a pipe thread compound approved for the type of gas supplied.

If flexible metal tubing

If necessary for service. open the toe panel. Use a putty knife

3. Open the shut-off valve in the gas supply line and make sure the dryer has its own gas supply opened.

Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leaks found.

Type of Gas

This dryer is equipped for use with natural gas.

It is design-certified by CSA International for LP (propane and butane) gases with appropriate conversion. No attempt shall be made to convert dryer from gas specified on serial/rating plate for use with a different gas without consulting the serving gas supplier. Conversion must be done by a qualified service technician.

Gas conversion kit part numbers are listed near gas valve burner base.

Gas Supply Line

Recommended Method

Provide a gas supply line of 1/2” (13 mm) rigid (IPS) pipe to dryer location. Pipe joint compounds that resist action of LP gas must be used. Do not use TEFLON* tape. With LP gas. piping or tubing size can be 1/2” (13 mm) minimum. Usually. LP gas suppliers determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping. accessible for gauge testing. must be installed immediately downstream of the installed shut-off valve to the dryer (as shown above). The dryer must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 1/2” psig (352 kg/m’).

Alternate Method

The gas supply may also be connected using 3/8" (10 mm) approved copper or aluminum tubing. If the total length of the supply line is more than 20 ft. (6.1 m). larger tubing will be required.

If using natural gas. do not use copper tubing. Pipe joint compounds that resist action of type of gas supplied must be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off valve installed within 6 ft. (1.8 m) of dryer in accordance with National Fuel Gas Code. ANSI 2223.1. This valve should be located in same room as dryer. lt should be in a location that allows ease

In Canada. an individual manual shut-off valve must be installed

Flexible Metal Appliance Connector

It is recommended that a new flexible stainless steel gas line. design-certified by CSA International. be used for connecting the dryer to the gas supply line. (The gas pipe which extends through the lower rear of the dryer is provided with 3/8" [10 mm] male pipe thread.)

NOTE: Do not kink or damage the flexible stainless steel gas line when moving the dryer.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to the dryer.

+®@TEFLON is a registered trademark of E.l. Du Pont De Nemours and Company.

INSTALLING LEVELING LEGS. COIN SLIDE. AND COIN BOX

On some models: The console houses the electronic control board. The board is factory set for a dry time of 45 minutes.

Consult the tech sheet found inside the dryer toe panel to reset dry time and for other options.

The card reading mechanism is not included. but is available from your usual industry sources.

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. Prepare dryer for leveling legs NOTE: Slide dryer onto cardboard or hardboard before moving

Using two or more people. move dryer to desired installation location.

Take tape off front corners of dryer. Open dryer and remove the literature and parts packages. Wipe drum interior with a damp cloth to remove any dust.

Take two cardboard corners from the dryer carton and place them on the floor in back of the dryer. Firmly grasp the body of the dryer and genily lay it on its back on the cardboard corners. Disconnect power before making electrical connections.

(appearance may vary)

2. Screw in leveling legs

Examine leveling legs and find diamond marking. Screw legs into leg holes by Diamond hand. Use an adjustable wrench or Marking

1" (25 mm) hex-head socket wrench

To protect the floor. use a large piece of cardboard from the dryer carton. Stand dryer up on the cardboard. Slide the dryer until

On some models: The meter case houses the factory-installed accumulator timer with actuating arm or service switch.

The factory-installed timer is set to provide 45 minutes (4 pins)

The coin slide mechanism. service door lock and key. and coin box lock and key may not be included but are available from the usual industry sources.

Install coin slide and coin box

Remove the service door of the meter case by lifting it up at the back. Install the money-accepting device. (Refer to manufacturer's instructions for proper installation.)

For dryers using coin slides. use the adapter kit supplied with the dryer.

Replace the meter case service door. Put the coin vault with lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust the legs

Install added security device

Check that power is not supplied to the dryer.

Open and remove the service door.

Insert the narrow part of the security cone into the oblong hole in the bottom rear of the meter case assembly.

Pass the security bolt through this cone and thread it by hand into the cage nut below the oblong hole.

Tighten the security bolt by hand a few turns before using a wrench

: \ ee Security ol (C3 Cone

NOTE: Installing the security bolt provides added security. but

ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY)

Strain Relief

Remove Terminal Block Cover Power Supply Cord Strain Relief

1. Insert strain relief.

CN ay

(appearance may vary)

Strain Relief

Direct Wire Strain Relief

1. Insert strain relief.

2. Insert conduit into strain relief and tighten clamp.

Connection Options

Power Cord Direct Wire

4-wire receptacle (NEMA Type 14-30R) 4-wire direct 5 ran) eo

(lap tm

3-wire receptacle (NEMA Type 10-30R) 3-wire direct

9 mm)

Connecting 4-Wire Connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.

Standard Power Supply Cord Connectors Connecting Direct Wire Ground

3. Connect ground wire (green or bare) (E) of power supply cord ye 0x8) under green external ground conductor screw (C). Tighten

Flanged Spade Connector Ring Connector SCTOW.

Connecting Neutral Ground and Neutral Wires

1. Remove center terminal block screw (A) and the neutral ground wire (B) by removing the green external ground conductor screw (C).

Connecting Remaining Wires

4. Connect remaining wires under outer terminal block screws

(F). Tighten screws. Finally. reinstall terminal block to dryer rear panel. Secure cover with hold-down screw.

2. Connect neutral ground wire (B) and neutral wire (white or center wire) (D) of power supply cord under center terminal block screw (A). Tighten screw.

Connecting 3-Wire Connection: Power Supply Cord

Standard Power Cord Connectors

Ring Connector Flanged Spade Connector

Connecting Neutral Wire

1. Loosen or remove center terminal block screw (A).

Connecting 4-Wire Connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable. leaving bare ground wire at 5" (127 mm). Cut 112" (38 mm) from 3 remaining wires. Strip insulation back 1" (25 mm). Shape ends of wires into

2. Connect neutral wire (white or center wire) (D) of power supply cord under center terminal block screw (A). Tighten screw.

RB A

3. Connect remaining wires under outer terminal block screws

(F). Tighten screws. Finally. reinstall terminal block to dryer rear panel. Secure cover with hold-down screw.

Connecting Neutral Ground and Neutral Wires

1. Remove center terminal block screw (A) and the neutral ground wire (B) by removing the green external ground conductor screw (C).

Connecting 4-Wire Connection: Direct Wire

Connecting Neutral Ground and Neutral Wires (cont.

2. Connect neutral ground wire (B) and place hooked end (hook facing right) of neutral wire (white or center wire) (D) of direct wire cable under center terminal block screw (A). Squeeze hooked ends together and tighten screw.

Connecting Direct Wire Ground

3. Connect ground wire (green or bare wire) (E) of direct wire cable under green external ground conductor screw (C).

Tighten screw.

Connecting 3-Wire Connection: Direct Wire

Connecting Remaining Wires

4. Connect remaining wires under outer terminal block screws

(F). Squeeze hooked ends together and tighten screws. Finally. reinstall terminal block to dryer rear panel. Secure cover with hold-down screw.

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed.

Strip 3%" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm).

If using 3-wire cable with ground wire.

Connecting Neutral Wire

1. Loosen or remove center terminal block screw (A).

2. Place hooked end of neutral wire (white or center wire) (D) of direct wire cable under center terminal block screw (A). hook facing right. Squeeze hooked end together and tighten screw.

3. Connect remaining wires under outer terminal block screws

(F). Squeeze hooked ends together and tighten screws. Finally. reinstall terminal block to dryer rear panel. Secure cover with hold-down screw.

Connecting 3-Wire Connection: Optional

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

Connecting Neutral Wire

1. Remove center terminal block screw (A). Also remove neutral ground wire (B) by removing green external ground conductor screw (C).

2. Connect neutral ground wire (B) and neutral wire (white or center wire) (D) of power supply cord/cable under center terminal block screw (A). Tighten screw.

LEVELING

Leveling your dryer properly reduces excess noise and vibration.

MPN fe

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

3. Connect remaining wires under outer terminal block screws (F).

Tighten screws.

Connect a separate copper ground wire (G) under the green

1. Remove cardboard from beneath dryer. Place a level on top edges of dryer. checking each side and front.

If not level. tip dryer and adjust legs up or down as shown in Step 3. repeating as necessary.

(appearance may vary)

Not Level LEVEL Not Level

2. Grip dryer from top and rock back and forth. making sure all four legs are firmly on floor. Repeat. rocking dryer from side to side.

If dryer rocks. go to Step 3 and adjust leveling legs.

(appearance may vary)

If dryer is not level. use a 1” or 25 mm open-end or adjustable wrench to turn the leveling leg counterclockwise to lower the dryer or clockwise to raise the dryer. Recheck levelness of dryer and that all four legs are firmly in contact with the floor. Repeat as needed.

HELPFUL TIP: You may want to prop up front of dryer about 4" (102 mm) with a wood block or similar object that will support weight of dryer.

COMPLETE INSTALLATION

1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements’

2. Check that all parts are now installed.

If there is an extra part. go back through the steps.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death.

5. Plug into a grounded outlet. or connect power.

6. Check dryer operation:

Models with Electronic Display: Close dryer door. Set the cycle. Operating time will accumulate per number of coins.

Mechanical Models: Some accumulated time may be on the timer due to factory testing. Close dryer door. Turn timer-set knob to the right. (Operating time will accumulate per number of depressions and type of timing cam used.) Push START button.

Using a full heat cycle (not the air cycle). let the dryer run for at least five minutes. Dryer will stop when time is used up. Make sure the dryer turns off.

NOTE: Dryer door must be closed for dryer to operate. When door is open. dryer stops. but timer continues to run. To restart dryer. close door and push START button (mechanical models

7. Open the dryer door. Check that the inside of the dryer is warm.

If the burner does not ignite and you can feel no heat inside the dryer. shut off dryer for five minutes. Check that all supply valve controls are in “ON” position and that the electrical cord

If drying time is too long. make sure that the lint screen is clean and that there are no obstructions to airflow in the dryer vent system.

9. Restart the dryer and allow it to complete a full heat cycle

(not air cycle) to make sure it is working properly.

REVERSING DRYER DOOR SWING (OPTIONAL)

You can change your door swing from a right-side opening

Be certain to keep cardboard spacer centered between doors. to left-side opening. if desired.

Reattach outer door panel to inner door panel so handle is on Remove the Door Assembly the side where hinges were just removed.

Place a towel or soft cloth on top of dryer or work space to avoid scratching of the surface.

2. Open dryer door. Remove bottom screws from cabinet side of hinges. Loosen (do not remove) top screws from cabinet side

Reattach screws at top. bottom. and side of door (5 screws).

Hinges

(appearance may vary) 9. Attach door hinges to dryer door so that larger hole is at the bottom of the hinge and the hinge pin is toward the door front.

Lift door until top screws in cabinet are in large part of hinge

4. Remove screws attaching hinges to door.

5. Remove screws at top. bottom. and side of door (5 screws).

10. Remove the 4 screws that attach 2 plugs on the left side.

Attach plugs to right side using the same 4 screws.

11. Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position door so large end of door hinge slot

6. Holding door over towel on dryer. grasp sides of outer door and Tighten screws. Insert and tighten top screws in hinges.

12. Close door and check that door strike aligns with door catch.

If needed. slide door catch left or right within slot to adjust alignment.

CHANGING TO A 30- OR 60-MINUTE TIMING CAM

(on some models)

5. Place new cam (hub side down) over clock shaft. Line up flat WARNING side of shaft with flat side of cam hole. Check that drive lug is in place.

Electrical Shock Hazard

Drive Lug

Disconnect power before making cam changes.

Failure to follow these instructions can result in death

Coin-slide models: You can install the 30-minute or 60-minute timing cam (shipped with dryer) as follows:

1. Unplug dryer or disconnect power.

2. Unlock meter case.

3. Turn the timing cam by hand until the V-shaped notch lines up below the ratchet tooth.

V-Shaped Ratchet

7. Press cam down in place on clock shaft. Make sure that V-shaped notch clears the ratchet tooth.

4. Insert a narrow. flat-blade screwdriver under the timing cam near the clock shaft. Genily lift cam straight up and off shaft. making sure that the V-shaped notch clears the ratchet tooth.

8. Close and lock the meter case.

9. Plug in dryer or reconnect power.

MAINTENANCE INSTRUCTIONS

Clean lint screen before and after each cycle.

Removing accumulated lint:

From inside the dryer cabinet:

Lint should be removed every 2 years or more often. depending

From the exhaust vent:

Lint should be removed every 2 years. or more often. depending on dryer usage.

Keep area around dryer clear and free from combustible materials. gasoline. and other flammable vapors and liquids.

Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.

IF YOU NEED ASSISTANCE

If dryer does not operate. check the following:

Electrical supply is connected.

Circuit breaker is not tripped or house fuse is not blown.

Door is closed.

Controls are set in a running or “on” position.

START button has been pushed firmly.

For gas dryers. check that gas supply shut-off valves are set

Contact your authorized Commercial Laundry distributor. To locate your authorized Commercial Laundry distributor. or for web inquiries.

If you cannot locate your distributor. the Commercial Laundry Support Center will answer any questions about operating or maintaining your dryer not covered in the Installation Instructions.

Just dial 1-800 NO BELTS (1-800-662-3587) — the call is toll free.

When you call. you will need the dryer model number and serial number. Both numbers can be found on the serial-rating plate located

ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models)

IMPORTANT

Electrostatic Discharge (ESD) Sensitive Electronics

ESD problems are present everywhere. ESD may damage

Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance.

OR

Touch your finger repeatedly to a green ground connection point

I Before removing the part from its package. touch the anti-static bag to a green ground connection point or unpainted metal in the appliance.

Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.

IB When repackaging failed electronic control assembly

General User Information

BLANK DISPLAY —- This condition indicates the dryer is inoperative.

Enter set-up mode to view diagnostic code.

“0 MINUTES” SHOWING IN DISPLAY = This indicates the cycle

COLD START (initial first use) — Dryer is programmed at the factory as follows:

5 minutes dry time/quarter (coin 1)

$1.50 dry price (fixed cycle with top off - PD Models)

$0.00 dry price (fixed cycle - PR Models)

WARM START (after power failure) — A few seconds after power

PRICING = After the door is opened and then closed following the completion of a cycle. the display indicates the cycle price (unless

There are four (4) types of dryer pricing:

Fixed “Vend” Pricing

A dryer set up for “Fixed Cycle” operation can only accept additional time accumulated by increments equal to the length of a complete dry cycle. A maximum of 99 minutes may be purchased; no additional credit is given for coins dropped with 99 minutes in the display.

Accumulator Pricing

If the price is set to one coin 1. then accumulator pricing

Fixed Cycle With Top Off Pricing

A dryer set to offer “Top Off” capability will allow time to be added to an existing dry cycle in increments equal to the number

PR Models: In Enhanced Debit Mode. the top off price can be set independently (see VALUE OF COIN 2). and the top off time is calculated according to the following equation:

Penny increment offset is not applied to top off purchases.

FREE CYCLES - This is established by setting the cycle price

DEBIT CARD READY - This dryer is debit card ready. It will accept a variety of debit card systems. but does NOT come with a debit card reader. Refer to the debit card reader manufacturer for proper dryer setup. In models converted to a Generation 1 debit card system. debit pulses represent the equivalent of one coin (coin 1).

Display

After the dryer has been installed and plugged in. the display will show “OQ minutes.”

Single Load Models

WHITES PERM. ey AND COLORS PRESS DELICATES

Once the unit has been plugged in and the dryer door opened and closed. the display will show the price. In PR models set for free cycles. the display will flash “SELECT CYCLE” (not shown).

Single Load Models

WHITES PERM.

AND COLORS PRESS DELICATES

ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models)

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.

The fabric setting buttons along with the digital display are used

How to Use the Buttons to Program the Controls

1. The WHITES AND COLORS button is used to adjust the values associated with set-up code. Pressing the button will change the value by increments. Rapid adjustment is possible by holding down the button.

2. The PERM. PRESS button will advance through the set-up codes. Pressing the button will advance to the next available set-up code. Holding down the PERM. PRESS button will automatically advance through the set-up codes at a rate faster than 1 per second.

3. The DELICATES button is used to select or deselect options.

Start Operating Set-up

Single Load PD Models: Insert service door key. turn. and lift to remove service door.

Single Load PR Models: Once the debit card reader is installed {according to the reader manufacturer's instructions). the set-up mode can be entered by inserting a manual set-up card (supplied by the reader manufacturer) into the card slot. If manual set-up card is not available. manual set-up mode can be entered by removing connector AA1 on the circuit board.

IMPORTANT: The console must not be opened unless power is

~ Unplug dryer or disconnect power.

~ Open console. disconnect plug on AA1. close console.

— Plug in dryer or reconnect power.

The dryer is now in the set-up mode.

NOTE: This dryer is preset at the factory and does not require any programming. However. if you want to change the settings. follow the “Set-Up Codes” guide below.

& PD units are pre-set at the factory for fixed cycle price with top

& PR units are pre-set for free cycle operation so they can be run without readers or coins.

Set-Up Codes

The PERM. PRESS button will advance you from code to code.

The WHITE AND COLORS button will change the code value.

The DELICATES button will select or deselect options.

PR MODELS: The set-up codes are the same as for the PD models except where noted.

The set-up code is indicated by the one or two left-hand characters. The set-up code value is indicated by the two or three right-hand characters.

Code Explanation

REGULAR CYCLE PRICE

Represents the number of quarters (coin 1) needed

PR MODELS: Factory default of 6 00. or O quarters.

+ Press the PERM. PRESS button once to advance to next code.

REGULAR DRY TIME

PD MODELS: Represents the number of minutes per quarter (coin 1).

Factory default of 5 minutes per coin.

Example: 6 quarters x 5 minutes = 30 minutes.

By pressing the WHITES AND COLORS button. value adjusts from 1-99 minutes.

+ Press the PERM. PRESS button once to advance to next code.

TYPE OF DRYER PRICING

Fixed Cycle with Top Off. For detailed description. see “General User Information”

FC PR MODELS ONLY: Factory default of FC. Fixed Cycle.

For detailed description. see “General User Information?

Use the DELICATES button to change this selection.

+ Press the PERM. PRESS button once to advance to next code.

9 00 CYCLE COUNTER OPTION This option is either NOT SELECTED “OFF” or SELECTED “ON?

9 00 Not Selected “OFF?

Selected “ON” and not able to be deselected.

+ Press the DELICATES button 3 consecutive times

+ Press the PERM. PRESS button once to advance to next code.

If cycle counter (9 OC) is selected. the following is true:

1 00 Cycles in HUNDREDS

2 00 Cycles in ONES 225=

TOTAL CYCLES = 225

This is “VIEW ONLY” and cannot be cleared.

+ Press the PERM. PRESS button once to advance to next code.

ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models)

OPTIONS 3.XX — 9.XX TO USE IF SPECIAL PRICING

Code Explanation IS SELECTED

1. 00 MONEY COUNTER OPTION Cod Explanat This option is either NOT SELECTED “OFF" or ode _*pranavon SELECTED “ON?

3.06 SPECIAL CYCLE PRICE

1. 00 Not Selected “OFF” 3.06 Represents the number of quarters (coin 1) 1.0C Selected “ON” to start the dryer; may adjust from 0-39.

See VALUE OF COIN 1 b.05).

+ Press the DELICATES button 3 consecutive times to ( ch 0-39 b th select “ON” and 3 consecutive times to remove (Not Aavance trom U= y pressing the Selected “OFF”). Counter resets by going from “OFF” WHITES AND COLORS button. Factory default to “ON” of 6 quarters = $1.50.

1.CO Selected “ON” and not able to be deselected.

3.00 PR MODELS: Factory default of 0 quarters.

+ To select “ON" and not able to be deselected

+Press the PERM. PRESS button once to advance to

+ Press the PERM. PRESS button once to advance to 4.05 PD MODELS: Represents the number of minutes per next code. quarter (coin 1).

° Factory default of 5 minutes per coin.

2. 00 orecl eRe OT SELECTED “Orr?

Example: 6 quarters x 5 minutes = 30 minutes.

SEE STED “ON” or

+ By pressing the WHITES AND COLORS button.

2.SP Selected “ON? to next code.

+ Press the DELICATES button once to change this selection.

+ Press the PERM. PRESS button once to advance to next code.

5.00 TIME-OF-DAY CLOCK. MINUTES

If money counter (1.0C or 1.CO) is selected. the following is true:

5 00

Dollars in HUNDREDS 3 01 = $100.00

Dollars in ONES 468=$ 68.00 Number of CENTS 575=$ 00.75

TOTAL = $168.75

5. 00 This is the TIME-OF-DAY CLOCK. minute setting; select 0-59 minutes by pressing the WHITES AND COLORS button.

+ Press the PERM. PRESS button once to advance to next code.

NOTE: TIME-OF-DAY CLOCK does not keep time when power is interrupted by unplugging or power failures. A back-up battery is required to maintain the correct time

NOTE: Uses military time or 24 hr. clock.

6. 00 This is the TIME-OF-DAY CLOCK. hour setting; select 0-23 hours by pressing the WHITES AND COLORS button.

+ Press the PERM. PRESS button once to advance to next code.

NOTE: TIME-OF-DAY CLOCK does not keep time when power is interrupted by unplugging or power failures. A back-up battery is required to maintain the correct time

ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models)

Code Explanation Code Explanation

7. 00 SPECIAL PRICE START HOUR b.05 VALUE OF COIN

NOTE: Uses military time or 24 hr. clock. b.05 This represents the value of coin in number of nickels:

7.00 This is the start hour; O—-23 hours.

05 = $0.25.

+ Select START HOUR by pressing the WHITES AND

+ By pressing the WHITES AND COLORS button. there COLORS button. is an option of 1-199 nickels.

+ Prass the PERM. PRESS button once to advance to ° Press the PERM. PRESS button once to advance to next code.

8.00 SPECIAL PRICE STOP HOUR C.20 VALUE OF COIN 2/VALUE OF DRYER TOP OFF

NOTE: Uses military time or 24 hr. clock.

C.20 This represents the value of coin 2 in number of nickels:

8.00 This is the stop hour; 0-23 hours. oe moons Factory default of $0.25

Factory default of $0.25.

° ee HOUR by pressing the WHITES AND For models using Enhanced Debit. this field represents utton. the value of top off in nickels.

+ Press tne PERM. PRESS button once to advance to e By pressing the WHITES AND COLORS button. there

9.10 SPECIAL PRICE DAY

+ Press the PERM. PRESS button once to advance to

9.10 This represents the day of the week and whether special next code. pricing is selected for that day. A number followed by d.00 COIN SLIDE OPTION “0” indicates no selection that particular day (9.10). A This option is either NOT SELECTED “OFF” or number followed by an “S” indicates selected for that SELECTED “ON” day (9.1S). Days of the week (1-7) are selected by pressing the WHITES AND COLORS button. Press the d.00 Not Selected “OFF DELICATES button once to select special pricing for each d.CS Selected “ON? day chosen. ° Press the DELICATES button 3 consecutive times When exiting set-up code “9” the display must show the current for this selection. When coin slide mode is selected. day of week: set “b.” equal to value of slide in nickels. Set “606 (REGULAR CYCLE PRICE) and “3.06” (SPECIAL DISPLAY DAY OF WEEK CODE (selected) CYCLE PRICE) to number of slide operations.

Day 1 = Sunda NOTE: If the installer sets up “CS” on a coin drop model.

Day 4 = Wednesday E.00 ADD COINS OPTION Day 5 = Thursday This option is either NOT SELECTED “OFF” or Day 6 = Friday SELECTED “ON? This option causes the customer Day 7 = Saturday display to show the number of coins (coin 1) to enter. rather than the dollars-and-cents amount. The number

° Press the PERM. PRESS button once to advance to in the display changes as the coins are accepted.

A.00 VAULT VIEWING OPTION E.AC Selected “ON?

This option is either NOT SELECTED “OFF” or

+ Press the DELICATES button 3 consecutive times to SELECTED “ON: change this selection.

A.00 Not Selected “OFF” PR MODELS ONLY: In enhanced debit mode. this option A.SC Selected “ON” is not selectable.

+ Press the DELICATES button once to change this selection. When selected. the money and/or cycle counts will be viewable (if counter option(s) is selected) when the coin box is removed.

+ Press the PERM. PRESS button once to advance to next code.

+ Press the PERM. PRESS button once to advance to next code.

ELECTRONIC CONTROL SETUP INSTRUCTIONS (PR/PD models)

END of SETUP PROCEDURES

Code Explanation

J.Cd PAYMENT MODE (COIN/DEBIT OPTION) EXIT FROM SET-UP MODE

J.Cd Both coin and debit selected. Press the DELICATES Single-Load PD Models: Reinstall access door. button 3 consecutive times to change this selection.

Single-Load PR Models:

J.C Coins selected. debit disabled. Press the DELICATES ~> Unplug dryer or disconnect power. button 3 consecutive times to change this selection. — Open console. reinsert plug into AA1. close console.

Jid Debit Card selected. coins disabled. Press the > Pluaind DELICATES button 3 consecutive times to change this ug In aryer or reconnect power. selection.

J. Ed Enhanced Debit is self-selected when a Generation 2 DIAGNOSTIC GUIDE card reader is installed in the dryer. The Ed option cannot If the set-up mode is entered and one of the following has be manually selected or deselected. occurred. the appropriate diagnostic code will be in the display.

+ Press the PERM. PRESS button once to advance to SINGLE DRYERS next code.

L.00 PRICE SUPPRESSION OPTION noche This option is either NOT SELECTED “OFF” or di Dryer door sense error on SELECTED “ON? This option causes the customer control board or due to power display to show “ADD” or “AVAILABLE” rather than line interference (cycles and the amount of money to add. (Used mainly in debit price display disabled until installations.) diagnostic code is manually

L.00 Not Selected “OFF” cleared).

L.PS Selected “ON” d4 Dryer motor control circuit error

(cycles and customer display

° Press the DELICATES button once to change this disabled until diagnostic code is

° Press ine PERM. PRESS button once to advance to d5 Blocked coin or coin drop

+ Press the DELICATES button once to change this interference (cycles and selection. customer display disabled until diagnostic code is manually

° Press the PERM. PRESS button once to advance to cleared). next code. di3 Blocked coin 2 or coin drop U.00 PENNY INCREMENT OFFSET control circuit failure (coin

U.00 This represents the penny increment price offset used in recognition and price display

Generation 2 (Enhanced Debit) PR models. Choose from 0-4 pennies by pressing the WHITES AND COLORS button.

+ Press the PERM. PRESS button once to advance to next code.

W10474273A 42/2012 W10474274A - SP



Newest Added: MER6875AAQ MDB5601AWW3 M8RXDGFXB00 MGC7430DS00 MFT2776DEM02

Maytag MDE18MNAZW0 | Pages: 60 | File type: PDF | Filename: 47382495_mde18mnazw0.pdf | Size: 8.53 MB | Language: English

Download User Manual

Product Infomation and Reviews - MDE18MNAZW0 photo

MDE18MNAZW0 Photo

Maytag in United States

1-800-344-1274 Hours of Operation Mon-Fri: 8 a.m. - 8 p.m. EST