Loading ...
Loading ...
Loading ...
18
Problem Cause Acon
Dishwasher
does not
start
Door may not be properly latched.1.
Unit may not be turned on.2.
Unit not reset or previous cycle not complet-3.
ed.
Delay start engaged.4.
Interrupon of electrical power supply to dish-5.
washer or blown fuse.
Child lock acvated (select models).6.
The door may have been closed without rst 7.
selecng a cycle.
Water supply may not be turned on.8.
Shut the door completely.1.
Press the main power switch to turn unit on.2.
To reset, refer to “Canceling or changing the cycle” secon 3.
in this manual.
To reset, refer to “Delay Start” secon in this manual.4.
Check circuit breaker.5.
Deacvate the child lock. Refer to “Child Lock” secon in 6.
this manual if applicable.
Select a cycle and close the door.7.
Check and turn on water supply.8.
Dishwasher
beeping
(end of cycle
signal)
Default factory sengs alert the customer that the
cycle has completed by beeping. This feature can
be deacvated if so desired.
To adjust the volume or deacvate, refer to “Cycle Compleon
Signal” secon in this manual.
Display does
not illumi-
nate or con-
sole lights
are not on
A fuse may have been blown or circuit breaker 1.
tripped.
Door not closed or latched.2.
Note: For models with controls on the top poron
of the door, the display only illuminates when the door is
opened and controls are visible.
Check the fuse or circuit breaker box and replace the fuse 1.
or reset the breaker if necessary.
Ensure that door is properly latched and completely 2.
closed.
Dishwasher
seems to run
a long me
Incoming water is not warm enough. 1.
Cycle me can vary due to soil and water condi-2.
ons.
Rinse agent dispenser is empty.3.
Dishwasher connected to cold water supply.4.
Note: Refer to “Cycle Chart Data” secon in this
manual for typical cycle length.
Before starng a cycle, run hot water faucet at the sink 1.
nearest to the dishwasher.
Sensors in the dishwasher automacally increase the cycle 2.
me to ensure a good wash when heavy soil is detected.
Add rinse agent. 3.
Verify dishwasher is connected to hot water supply plumb-4.
ing.
Dishes aren’t
geng clean
enough
Spray arm movement is obstructed.1.
Spray arm nozzles clogged.2.
Improper use of detergents.3.
Filters could be clogged.4.
Dishes are nested or loaded too close to-5.
gether.
Selected wash cycle is not suitable for food soil 6.
condons.
Ensure that spray arm movement is not blocked by hand 1.
rotang spray arms.
Remove the spray arms and clean according to “Check/2.
Clean the Spray Arm Nozzles” in Care and Maintenance
secon of this manual.
Increase or decrease detergent depending on the water 3.
hardness. Refer to Table under “Adding Detergent and
Rinse Agent”.
Clean the lter. Refer to “Check/Clean the Filter System” 4.
under Care and Maintenance secon of this manual.
Rearrange load such that water spray can reach all items in 5.
the dishwasher. See also “Preparing and Loading” secon
of this manual.
Refer to “Wash Cycle” secon in Operang the Dishwasher 6.
secon of this manual.
Dishes are
not geng
dry enough
Rinse agent dispenser is empty. (Rinse agent 1.
indicator is acvated).
Improper loading of dishes.2.
Selected cycle does not include drying.3.
Note: Plasc or Teon do not typically dry as com-
pletely as other items due to their inherent proper-
es.
Add rinse agent. The use of rinse agent improves drying.1.
Rearrange load to ensure items are not nested. Refer 2.
also to the “Preparing and Loading” secon of this
manual.
Rinse and Hold seng does not include drying cycle,3.
Note: Select models oer an extra heang opons to im-
prove drying performance. Refer to “Wash Cycle opons”
under the Operang the Dishwasher secon of this manual.
SELF HELP
Dishwashers may occasionally exhibit problems that are unrelated to a malfuncon of the dishwasher itself. The following informa-
on may help you with a dishwasher problem without involving a repair professional.
Loading ...
Loading ...
Loading ...