SKU Number: 351-8425
351-8721
Norm LED Ceiling Light
Model Number: NRMF1515L30D1PC
NRMF1515L30D1BK
HARDWARE CONTENTS Note: Hardware shown not actual size.
Gem Bar
x1
AA
BB
Junction Box
Screws
x2
CC
Wire Nuts
x3
PACKAGE CONTENTS
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-873-2326
Monday - Friday, 8:00 am-4:30 pm Central Standard Time
A
1
DD
Flathead Screw
x2
2
PREPARATION
Disconnect electrical power at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included.
If parts are missing or damaged, do not attempt to assemble the product. Contact customer service at 1-800-873-2326
Monday - Friday, 8:00 am-4:30 pm Central Standard Time for replacement parts.
Estimated assembly time: 30 minutes.
SAFETY INFORMATION
Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply
with these instructions could result in potentially fatal electric shock and/or property damage.
It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and
local electrical codes.
WARNING: Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a
wet or damp surface or in water.
WARNING: To reduce the risk of electrical shock, and to assure proper operation, this fixture must be adequately
grounded. To accomplish proper grounding, there must be a separate ground wire (green) contact between this fixture and
the ground connection of your main power supply panel.
WARNING: This product can expose you to lead, which is known to the State of California to cause cancer, birth defects
or other reproductive harm. For more informaton go to www.P65Warnings.ca.gov
CAUTION: This fixture is designed for use in a 120VAC, 60Hz fused circuit and can be used in conjunction with most 2-wire,
triac dimmers. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
MINIMUM 90˚C SUPPLY CONDUCTORS.
This fixture is intended to be used for general indoor lighting in dry or damp locations only.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules and Canadian ICES-005. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modifications to this fixture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
1. Separate the gem bar (AA) from the fixture canopy (A) by removing
two canopy screws (DD).
3. Make all wire connections to appropriate wire. Secure with wire
nuts (CC – provided). Connect the green wire from the fixture to
the supply power source ground wire. Connect the black wire from
the fixture to the black (L) wire from supply power source. Connect
the white wire from the fixture to the white (N) wire from supply
power source. Do not mix wires. Pull on each wire lead to make
sure connections are secure. Make certain no bare wires are
exposed outside of wire connectors. Tuck all connections neatly
into the junction box.
2. Mount gem bar (AA) to the junction box (not included) using two
junction box screws (BB) (provided).
Wiring – all wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box.
Check power wires for damage or scrapes. If power supply wires
are within three inches of the LED driver, use wire suitable for at
least 90°C (194°F). Note: Most dwellings built before 1985 have
supply wire rated to 60°C. Consult a qualified electrician to ensure
correct branch circuit conductor before installing.
4. Mounting
Place fixture canopy (A) over the gem bar (AA) and align the
mounting holes on both sides of the canopy. Secure the fixture
using two canopy screws (DD).
Power to the fixture may now be restored.
ASSEMBLY INSTRUCTIONS
3
3
2
1
A
CC
AA
BB
AA
A
DD
DD
4
AA
CARE AND MAINTENANCE
TROUBLESHOOTING
Use a dry or slightly damp clean cloth to wipe the surface of the fixture. Do not use any cleaner
with chemical solutions and abrasive pad. If necessary, use a mild soap with water to clean off any dirt or
stains.
1. The light does not come on at all:
a) Make sure the wall switch and circuit breaker are turned on
b) Make sure all wiring connections are connected and secured.
2. Fuse blown or circuit trips when light is turned on:
a) Check for crossed wires, ensure wiring is correct
If unable to fix any of the above issues, please consult a certified electrician.
FIVE-YEAR LIMITED WARRANTY: If during normal use, this PATRIOT LIGHTING
®
lighting fixture breaks or
fails due to a defect in material and workmanship within (5) years from the date of original purchase, simply
bring this lighting fixture with the original sales receipt back to your nearest MENARDS
®
retail store. At its
discretion, PATRIOT LIGHTING
®
agrees to have the product or any defective part(s) repaired or replaced with
the same or similar PATRIOT LIGHTING
®
product or part free of charge, within the stated warranty period,
when returned by the original purchaser with original sales receipt. This warranty; (1) excludes expendable
parts including but not limited to light bulbs; (2) does not cover damage that has resulted from abuse or misuse;
and (3) does not cover any losses, labor, injuries to persons/property or costs. This warranty does give you
specific legal rights and you may have other rights,which vary from state to state.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-873-2326
Monday - Friday, 8:00 am-4:30 pm Central Standard Time
8061497
4
