Loading ...
Loading ...
Loading ...
Step-by-stepinstallation instructions.
Sanitizing Procedures
Tocompletethe installation,do the following sanitizingprocedures.
Care is taken at the thctoD_ to keep y_)ur water softener clean and sanitmy. Materials used to make tile softener _dll not intect or
contmninate your water supply and _dll not cm_se bacteria to ti_rm or gr_w. H_wever, (hning shipping, storage, installing and
operating, bacteria c{mld get into the softener. For this reason, sanitizing as fifth_ws is suggested when installing.
NOTE:Sanitizingis recommendedby the WaterQualityAssociationfordisinfecting.
[_Be sure to (omplete all installation steps, in( luding programming tile (onuol.
[_ Pour about 3/4 oz. (l {dtablespoons) of COlnlnon 5.25% household bleach (Clorox, Linco, Bo Peep, White Sail, Eagle, etc.)
into tile brinewell,Refer to illusuation on page 6.
_IMPORTANT: Press and hold fi)r 3 seconds the faceplate TOUCH/HOLDbillion to start an imme(fiate regeneration. RechargeNow
begins to flash in the display. The blea(h is (hm_l into and through the water softener.
[_] If after sanitization water flOln house thucet tastes sahv or has a slight color, this is a present,alive fiom the resin tank. Turn on
the cold soft water fimcets and &ain fi)r a few minutes or until clear.
NOTE'Whenthe above sanitizing regeneration is over, your house COLDwater supply is flflly soft imme(fiately. However, your water
heater isfilled with hard water and as hot water is used, it will refill with soft water. When all the hard water is replaced in the water
heater, hot only and mixed hot and cold water will be tully soft. Ifyou want totally soft water immediately, after the ab_ve
reg*_neration, drain the water heater until the water runs cold.
_kWARNING: If you do drain the water heater, use extreme (are as the hot water (ould (ause burns. Turn the water heater off
prior m draining.
SPECIFICATIONS/DIMENSIONS
Rated capacily*
Amount of high capacit? resin (lbs/cu. fl)
Resin tank nominal size (in., dia. x height)
Se_'ice tlow rate (gpm)
O" )o"
Water suppl) maxinmm hardness (_I _)
Water supply maximum clear water iron (ppm)**
Water pressure limits (min.-m_e¢.psi)
l'ressure drop at rated service flow (psig)
Water temperature maximum (°F)
Water supply minimum flow rate (gpm)
Regeneration _)cle tlow rates (gpm)
Fill 0low to brine tank)
l?,rining }
l?,rine Rinse [low to drain)
l?,ackwash
FastRinse
(,XSF2 ¢ (,NSF3b (,XSF3.)
(see rating label on water softener)
r_, r./l36A/.7 48A/.93 .2.0
8 x 40 9 x 40 9 x 40
(see rating label on water softener)
100 100 100
5 6 8
20-125 20-125 20-125
15 15 15
120 120 120
3 3 3
.3 .3 .3
.19 20 20
.12 A6 .16
1,8 2.0 2.0
1,8 2.0 2.0
"11"--18 I'U
'ti l't"
>I '2"
These syslems con/k_nnIo WQA S-100 li)r the spedlic capadty claims as vefilied and substantiated by lest dala.
Testing wasperti)rmed using pellet grade sodium chh wide as the regeneranl sah.
'_'_Extant ol iron removal may varywith conditions, tse ol l)iamond ()ystal Red.Out or Super h-on Out' willimprove iron removal. Ref_r Io gleaning Iron Out of
the WaterSoftening Systemsecdon.
/0
Loading ...
Loading ...
Loading ...