Loading ...
Loading ...
Loading ...
Operation Guide 5590
E-49
Stopwatch:
Measuring unit: 1/100 seconds (first hour);
1 second (after first hour)
Measuring capacity: 23:59'59"
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer:
Measuring unit: 1 second
Countdown range: 24 hours
Countdown start time setting range: 1 second to 24 hours (1-second increments)
Alarms: 5 Daily alarms; Hourly time signal
Illumination: Double LED (light-emitting diode); Selectable illumination duration
(approximately 1.5 seconds or 3 seconds)
Other: Button operation tone on/off; Moving the Hands to View the Digital Display
E-48
Specifications
Accuracy at normal temperature: ±15 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the
week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 48 city codes);
Standard Time/Daylight Saving Time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 20seconds)
World Time: 48 cities (31 time zones) and Coordinated Universal Time (UTC)
Other: Daylight Saving Time/Standard Time; Home City/World Time City
switching
E-47
Main Indicators
Number Name See
1
1
PM indicator E-15
2
2
Split indicator E-29
3
3
Hands shifted indicator E-13
4
4
Mute indicator E-43
5
5
Alarm on indicator E-36
6
6
Hourly time signal on indicator E-38
7
7
DST indicator E-20, E-27
1
4 7
2 3
65
E-46
World Time Mode
■ The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving
time. See “To specify standard time or daylight saving time (DST) for a city” (page E-27)
for more information.
E-45
Troubleshooting
Hand Movement and Indications
■ The time indicated by the hands is different from the digital time.
This could indicate that the watch has been exposed to magnetism or strong
impact, which has caused problems with proper hand alignment. Adjust the watch’s
hand home position alignment (page E-41).
Time Setting
■ The current time setting is off by hours.
Your Home City setting may be wrong (page E-18). Check your Home City setting and
correct it, if necessary.
■ The current time setting is off by one hour.
You may need to change your Home City’s standard time/daylight saving time
(DST) setting. Use the procedure under “Adjusting the Digital Time and Date
Settings” (page E-21) to change the standard time/daylight saving time (DST) setting.
E-44
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A until the flashing SET indicator
disappears from the display and the currently selected city code appears on the
display.
2. Press C nine times to display the button operation tone On/Off screen (page
E-22).
The screen will show either KEY
or MUTE.
3. Press D or B to toggle the button operation tone setting between enabled
(KEY
) and disabled (MUTE).
4. Press A to exit the setting mode.
Note
x The mute indicator is displayed in all modes when the button operation tone is
disabled.
E-43
Button Operation Tone
You can turn the button operation tone on or off as
desired.
x Even if you turn off the button operation tone, alarms,
the Hourly Time Signal, and other beepers all operate
normally.
E-42
4. If the hour and minute hands are not at 12o’clock,
use D (+) and B (–) to adjust them until they are.
5. Press A to return to the Timekeeping Mode.
Check to make sure that the time indicated by the
hands matches the time on the digital display. If the
times don’t match, perform the correction procedure
above again.
Hour hand and minute hand
E-41
Adjusting Hand Positions
The watch hands can go out of alignment with the time on the digital display if it
is exposed to strong magnetism or impact. If this happens, you should adjust the
hand positions.
1. In the Timekeeping Mode, hold down A for at least
fiveseconds until SUB starts to flash. Release A after
SUB flashes.
x This enters the mode hand adjustment mode.
2. If the mode hand is not pointed at the adjustment point
mark ( ■ ) at 9o’clock, use D and B to move it there.
x Holding down either button moves the hands at high
speed.
3. Press C.
x This causes 0:00 to flash to indicate the hour and
minute hand adjustment mode.
Mode hand
Adjustment point mark
E-40
To change the illumination duration
1. In the Timekeeping Mode, hold down A until the flashing SET indicator
disappears from the display and the currently selected city code appears on the
display.
2. Press C ten times to display the illumination duration setting screen.
x The current illumination duration setting (1 or 3) will be flashing in the display.
3. Press D or B to toggle the illumination duration between three seconds
(3displayed) and 1.5 seconds (1displayed).
4. Press A to exit the setting mode.
Loading ...
Loading ...
Loading ...