Loading ...
Loading ...
Loading ...
• 5 •
5.3 USING THE WORK LIGHT
1. Position the jump starter on a at, stable surface near the intended work area.
2. Ensure the battery clamps are securely clipped on the storage holders.
3. Flip the ON/OFF power switch to the ON position.
4. Press the Battery Status/Light button on the front of the unit for 0.75 second, to turn on the work light.
5. When nished using the work light, press the button for 0.75 second, to turn off the work light.
6. Recharge the unit as soon as possible after each use.
5.4 USING THE AIR COMPRESSOR
WARNING. Read the instructions of the product being inated before using the compressor. Avoid overination; do not exceed the manufacturer’s recommended
pressures. Do not leave the air compressor unattended during use.
1. Remove the air compressor hose from the storage cleats.
2. Connect the adapter to the valve stem by threading it onto the end. If necessary, use one of the additional adapters.
3. Turn ON the compressor power switch and inate to the desired pressure or fullness.
NOTE: To prevent overheating, the compressor has built-in thermal protection that will turn the compressor off before it overheats. If the compressor shuts off, wait a few minutes
and it will automatically restart when the compressor cools.
4. When the desired pressure is reached, move the compressor power switch to OFF and unthread the connector from the valve stem.
5. Wrap the compressor hose around these cleats when it is not being used.
6. Allow unit to cool.
7. Recharge the unit before storing.
NOTE: The air compressor is rated for 150 PSI.
ESTIMATED TIME FOR INFLATING
Vehicle tires 13-16" 6-24 minutes
Bike tires 1-3 minutes
Sports balls 30 seconds
These times are approximate. Use the air compressor gauge to ensure the proper pressure has been reached. Do not overinate.
5.5
ENERGY SAVING MODE
If the unit is not used after the ON/OFF power switch is turned on, the unit will go into Energy Saving mode after 10 minutes to prevent battery discharge. Follow these
steps to use any function after Energy Saving mode:
1. Press the ON/OFF power switch to turn the unit ON.
2. The Green Ready/Fail LED will light.
3. After 10 minutes, The USB port and Battery Status/Light function will turn off.
4. After 10 minutes, The Green Ready/Fail LED will turn off.
5. Press the Battery Status/Light button once. The unit is now ready for checking the battery status and using the jump starter, compressor, USB and work light.
6. MAINTENANCE AND STORAGE
6.1 Clean the clips and the case each time you are nished using it.
6.2 Charge battery to full capacity before storage.
6.3 Store this unit at the temperatures between
-
4°F -
+
140°F (
-
20 ˚C -
+
60 ˚C).
6.4 Store clips on their support posts, to ensure they do not come into contact with any metallic surface.
6.5 Never completely discharge the internal battery.
6.6 Charge after each use.
6.7 Charge at least once every month, if not in frequent use, to prevent over-discharge.
7. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
The jump starter won’t jump start my car. Clamps are not making a good connection to the
battery.
Connections are reversed.
The jump starter’s battery is not charged.
The vehicle’s battery is defective.
The jump starter is not turned on.
Check for poor connection to battery and frame.
Make sure connection points are clean.
Disconnect the jump starter and reverse the clamps.
Press the Battery Status button on the front of the
unit. The LEDs will indicate the status of charge.
Have the battery checked.
Press ON/OFF switch to turn on the jump starter.
The jump starter will not operate. Low temperature protection. Use the USB adaptor to charge and activate.
The battery in the jump starter won’t hold a charge. The battery is bad (will not accept a charge). Have the battery checked.
The compressor shuts off. The compressor has built-in thermal protection that
will turn the compressor off before it overheats.
Wait a few minutes and it will automatically restart
when the compressor cools.
Loading ...
Loading ...
Loading ...