Loading ...
PRE-INSTALLATION REQUIREMENTS
Tools and MateHMs Required for ktstMladon:
1. PhiBps head screwdriver
2. Channe[qock adjustable pliers.
3, Carpenter's [evek
4, Flat or straight blade screwdriver,
5. Duct tape,
6, Rigid or flexible meta[ 4 inch (10.2 cm) duct,
7. Vent hood.
8, Pipe thread sealer (Gas).
9, Plastic knife.
ELECTRICAL REQUIREMENTS
ELECTR/C Dryer
CIRCUIT - individual 30 amp. branch circuit fused with 30 amp, minimum
time delay fuses or circuit breaker.
POWER SUPPLY - 3 wire or 4-wire, 240 volt, single phase, 60 Hz,
Alternating Current
POWER SUPPLY CORD KiT - The dryer MUST employ a 3<onductor
power supply cord NEMA 10-30 type SRDT rated at 240 volt AC
minimum, 30 amp., with S open end spade lug connedors with upturned
ends or closed loop connectors OR a 4<onductor power supply cord
NEMA 14-30 type SRDT or ST (as required) rated at 240 volt AC
minimum, 30 amp., with 4 open end spade lug connectors with upturned
ends or closed loop connectors and marked for use with clothes dryers.
If being installed in a new branch circuit installation, manufactured
(mobile) home, recreational vehicle or area which prohibits grounding
through the neutral conductor, the dryer MUST employ a 4<onductor
power supply cord NEMA 14-€0 type SRDT or ST {as required) rated at
240 volt AC minimum, 30 amp,, with 4 open end spade lug connectors
with upturned ends or closed loop connectors and marked for use with
clothes dryers, See ELECTRICAL CONNECTIONS for additional
instructions.
CANADA - A 4 wire power cord is installed on dryer,
OUTLET RECEPTACLE - NEMA 10-30R (3-wire) receptacle or NEMA 14-
30R (4-wire) receptacle to be located so the power supply cord is
accessible when the dryer is in the installed position
NEMA 10-30R NEMA 14-30R
I GAS Dryer
CIRCUIT - Individual 15 amp. branch circuit fused with a 15 amp.
maximum time delay fuse or circuit breaker.
POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz, Alternating
Current.
POWER SUPPLY CORD - The dryer is equipped with a 120 volt 3-wire
power cord,
Use separately fused circuits for washers and dryers, and DO NOT
operate a washer and a dryer on the same circuit.
NOTE: Do not under any
circumstances remove
grounding prong from
plug.
EXHA UST 5 Y$TEM REQUIREMENTS
Use only 4 inch (10,2 cm) diameter (minimum) rigid or flexible metal duct
and approved vent hood which has a swing-out damper(s) that open
when the dryer is in operation. When the dryer stops, the dampers
automatically close to prevent drafts and the entrance of insects and
rodents. To avoid restricting the outlet, maintain a minimum of 12 inches
(30.5 crn) clearance between the vent hood and the ground or any other
obstruction,
The following are specific requirements for proper
and safe operation of your dryer. Failure to follow these
instructions can create excessive drying times and fire hazards.
Do not use plastic flexible duct to exhaust the dryer
Excessive lint can build up inside exhaust system and create a fire hazard
and restrict air flow. Restricted air flow will increase dryer times. If your
present system is made up of plastic duct or metal foil duct, replace it
with a rigid or flexible metal duct. Ensure the present duct is free of
any riot prior to installing dryer duct.
If the dryer is not exhausted outdoors, some fine
lint wilt be expelled into the laundry area. An accumulation of lint in
any area of the home can create a heakh and fire hazard. The dryer
exhaust system MUST be exhausted to the outside of the dweRing!
Do not allow combustible materials (for example:
dothing, draperies/curtains, paper) to come in contact with exhaust
system. The dryer MUST NOT b_ exhausted into a chimney, a wall, a
ceiling, or any concealed space of a building which can accumulate lint,
resulting in a fire hazard.
Exceeding the length of duct pipe or number of
elbows allowed in the "MAXIMUM LENGTH" charts car/ cause an
accumuBdon of lint in the exhaust system. Plugging the system could
create a fire hazard, as well as increase drying times.
Do not screen the exhaust ends of the vent system,
nor use any screws or Hvets to assemble the exhaust system. Lint
can become caught in the screen, on the screws or rivets, clogging the
duct work and creating a fire hazard as well as increasing drying times.
Use an approved vent hood to terminate the duct outdoors, and seal all
joints with duct tape All male duct pipe fittings MUST be installed
downstream with the flow of air,
Explosion hazard. Do not install the dryer where
gasofine or other flammables are kept or stored. If the dryer is
installed in a garage, it must be a minimum of 18 inches (45.7 cm) above
the floor. Failure to do so can result in death, explosion, fire or burns,
Number
of
90°
Turns
0
1
2
3
4
Number
of
90°
Turns
0
I
2
3
(10.2 cm)
6O ft.
52 ft.
44 ft.
32 ft.
28 ft.
MAX/MUM LENGTH
of 4" (10.2 cm) Dia. Rigid Metal Duct
VENT HOOD TYPE
(Preferred)
Louvered
(18.28 m)
(15.84 m)
(13.41 m)
(9.75 m)
(8.53 m)
MAXIMUM LENGTH
of 4" {10.2 cm) Dia, Flexible Metal Duct
VENT HOOD TYPE
{Preferred)
Louvered
(I0.2 cm)
30 ft. (9,I4 m)
22 ft. (6,71 m)
14 ft. (4,27 m)
NOT RECOMMENDED
(6.35 cm)
48 ft.(14.63 m)
40 ft.(12.19 m)
32 ft. (9.75 m)
24ft, (7:11 m)
16 ft. (487m)
(6.35 cm)
18 ft. (5.49 m)
14ft. (4.27 m)
10 ft, (3.05 m)
Loading ...
Loading ...
Loading ...