Loading ...
Loading ...
Loading ...
4
PUMP SPECIFICATIONS:
TEMPERATURE ................. 77ºF (25ºC) Continuous
IMPELLER .......................... 2 Vane, open or vortex
SOLIDS HANDLING ........... 2” (51mm) spherical
PAINT .................................. Air dry enamel
SEAL ................................... Single Mechanical, oil-fi lled reservoir
CABLE ENTRY ................... 15 ft. (6m) quick disconnect cord
............................................. w/ plug on 120 volt and 240 volt, 1
............................................. phase, pressure grommet for sealing
............................................. and strain relief
UPPER BEARING ............... Single row, ball design, oil lubrication,
............................................. radial load
LOWER BEARING .............. Single row, ball design, oil lubrication,
........................ radial & thrust load
MOTOR ............................... NEMA L torque curve, oil-fi lled,
............................................. squirrel cage induction, Class B
............................................. insulation
SINGLE PHASE .................. Permanent Split Capacitor (PSC)
............................................. includes overload protection in motor
FLOAT ................................. Wide angle, PVC, mechanical,
............................................. normally open 15 ft. (6m), cable with
............................................. Piggy-back plug
BASIN ...................................Polythylene Basin
............................................... 20” x 30” or 25” x 24”
INLET FITTING ..................... For 4” (102mm) Sch. 40 inlet
COVER ................................. Sturctural Foam, grommets for
............................................... 2” (51mm) vent & discharge, cord
............................................... grommet, cover gasket and hardware;
............................................... optional access cover
CHECK VALVE ..................... 2” (51mm) vertical, Sch. 40 discharge
pipe compression
DESCRIPTION
Simplex Sewage package systems are good for residences,
commercial and small industrial sewage or sump applications.
Designed to handle nonexplosive and noncorrosive liquids, wastes
from lavatories, laundry tubs, fl oor drains and water closets. Pumps
push the water from below ground up to where normal drainage will
handle it. The package system shall NOT be installed in
locations classifi ed as hazardous in accordance with the United
States National Electrical Code (NEC), ANSI/NFPA 70 and shall be
vented in accordance with local plumbing codes.
NOTE
Pre-Assembled units contain water soluable packing inside. There
is no need to remove it.
Pump Material
Models Volute
Motor
Housing
Seal
Plate
Impeller Shaft
Square
Rings
Hardware Seal
SE411
SE421
SEV412
Cast Iron Cast iron Cast Iron Cast Iron 416 SS Buna-N
300 Series
SS
Silicon Carbide/
Buna-N
Models HP Volt Ph
NEMA
Start Code
Full
Load
Amps
Cord Size Cord Type
Cord O.D.
Inches (mm)
Winding
Resistance
Main - Start
SE411
SE421
SEV412
.4
.4
.5
115
230
115
1
1
1
C
C
H
12.0
6.2
10.5
14/3
14/3
14/3
SJTOW
SJTOW
SJTOW
.375 (9.53)
.375 (9.53)
.375 (9.53)
2.14 - 30.5
5.45 - 16.7
3.50 - 43.0
41 Gallon Sewage Station - Confi guration Matrix
Confi guration
Tank Type Confi guration Pump Voltage **
20” Dia. x
30” Dp.
25” Dia. x
24” Dp.
Basin
Kit *
Pre-Assembled SEV412 SE411 SE421 120V 230V
126902 X X X
126904 X X X
126908 X X X
126910 X X X
126914 X X X
126915 X X X
126916 X X X
126920 X X X
126921 X X X
126922 X X X
* Basin Kits are less the pump. A pump must be ordered seperately.
** The voltage selected is derived from the pump specifi ed.
Loading ...
Loading ...
Loading ...