Loading ...
Loading ...
Loading ...
USING TEMPLATES
This function allows you to create various labels
using the built-in templates. Refer to the Text Label
Templates section.
Example 1:
[Template that includes one
repeated graphic]
• There are three additional Text Label Templates
that allow you to use two different fonts on one
label. The procedure is similar to the steps in
Example 1; however, you will be prompted to
enter [Input Text 2].
Example 2:
[Template that includes two fonts]
Example 3:
[Template that includes two fonts
and a frame]
• The procedure is similar to the steps in Example 2.
Please see proceedure under Example 2.
Example 4:
[Template that includes two fonts on
two lines]
• The procedure is similar to the steps in Example 2.
Please see proceedure under Example 2.
This function allows you to create unique labels by
using built-in templates. Refer to the Pattern Label
Templates section.
You cannot enter text when using Pattern Label
Templates.
Example:
NOTE
For Text Label Templates
• You cannot set label length when printing Text
Label Templates.
• To clear the text, move the cursor to the right
side where you wish to clear and then press .
• To clear all text, press and , then “All
Clear” appears. Press to clear. Press
to cancel.
• You are able to preview labels by pressing the
Preview key when [Print] is displayed on the
LCD display.
• You cannot use the copy print function when
using Text Label Templates.
For Pattern Label Templates
• Press to return to the initial setting for
“Label Length” mode. The initial setting is
[3.9"(100 mm)].
• You cannot use preview feature when using
Pattern Label Templates.
For Text Label and Pattern Label Templates
• These templates are only available when using
0.47" (12mm) wide tape cassettes.
• The templates cannot be edited.
• To exit templates and return to the text input
screen, do one of following:
a) Press .
b) Press / to select [Quit], and then
press when "Print" appears.
• You cannot save labels created using templates
to memory.
• When you access Text Label or Pattern Label
Templates, your most recently printed Text Label or
Pattern Label Templates label length will be recalled.
• "Please Cut" is displayed on the screen for 2 seconds
after pressing when "Print" appears.
Text Label
[Select Category] /
[Text] [Select Design] /
[Input Text 1] Clear the
text and then enter text
[Print]
[Select Category] /
[Text] [Select Design] /
[Input Text 1] Clear
the text and then enter text
[Input Text 2] Clear the text and then
enter text [Print]
3
Pattern Label
[Select Category] /
[Patterns] [Select Design] /
[Set Label Length]
/ [1.2"-39.0" (30-999mm)]
[Print]
/ / -
Setting Margin ( )
[Full]/[Half]/[Narrow]
For leaving equal margins on both sides of the text.
[Chain Print]
Use this setting when printing several labels with
minimum margins.
1. Enter text.
2. Press , then [Copies: ] appears.
3. Press / or enter number with
number keys to select the number of copies.
4. Press . Printing will start, and then the
message "Feed OK?" appears.
5. Press to enter more text.
6. Clear the text, enter the text for the next label,
and then press .
7. When the message "Feed OK?" appears after
the last label is printed, press .
8. After the tape is fed, press the Cutter Lever to
cut off the chain of labels.
NOTE
• When [Chain Print] is set, feed the tape before using
the Cutter otherwise a part of the text may be cut off.
• When [Half] or [Narrow] is set, displayed label
length is the length from the printed dots ( ) to
the end of the label. Cut along the printed dots
(:) with scissors.
• To print more than 1 copy of a label with
minimum margin, set the margin to [Narrow].
• Do not pull the tape since this may damage the
tape cassette.
• After pressing , "Accepted" appears for
approximately one second.
You can save up to 30 labels and recall them for
printing at a later date. A maximum of 80 characters
can be saved per file, a maximum of 2400
characters can be saved in total memory. You can
also edit and overwrite the stored labels.
Save
Print
Open
NOTE
• You can also enter the File menu by pressing
.
• If you try to store a label when there is already a
label stored to that number, a message “Overwrite
OK?” will appear. Press to save your new
label. Press to cancel.
• You must type text before starting the save
function.
• After pressing , "Accepted" appears for
approximately one second.
Printing Labels (continued)
/ [Margin]
/ [Full/Half/Narrow/Chain Print]
LCD display Label image
Full
Half
Narrow
1"
0.16"0.16"
1"
ABC ABC
0.47" 0.47"
ABC
Full
Half
Narrow
2.7"
ABC
1.6"
ABC
1.0"
ABC
Saving Label Files
Enter Text / [Save]
/
/ [Print]
/
[Copies: ] / / -
/ [Open]
/
Loading ...
Loading ...
Loading ...