Loading ...
Loading ...
Loading ...
Owner's Manual
Operation ..........
i ",o, Plu_
_ OTE: THE PARTS LISTED ABOVE ARE HELPFUL FOR LOCATING THE
CONTROLS MENTIONED BELOW.
CAUTION: PRIOR TO FIRST USING THE GENERATOR, THE ENGINE MUST BE
FILLED WITH OiL OF A HIGH QUALITY SAE lOW-30 GRADE ENGINE OiL.
TO DO SO, UNSCREW AND REMOVE THE ENGINE'S OiL DIPSTICK LOCATED
AT THE BOTTOM OFTHE ENGINE CRANKCASE. FiLL THE ENGINE'S
CRANKCASE UNTIL THE OIL LEVEL IS LEVEL WITH THE UPPER MARKED
LINE ON THE DIPSTICK. THEN SCREW THE DIPSTICK BACK iNTO
THE OiL FiLL HOLE.
Before Starting the Generator Fuel tank capacdy:25L(6.6gallons)
1. Check that the engine power switch is in its
"OFF" position.
2. Before the first use, remove the fuel
tank cap and fill the fuel tank with unEeaded
gasoline. When fueling, be sure that the
fuel strainer is in place. Replace the fuel
tank cap. Thereafter, check the engine's
fuel gauge for the amount of unEeaded
gasoline in the fuel tank. If necessary, _L T_NK CAP
refill the fuel tank with unleaded gasoline;
the generator must be turned off and
cooled down before refilling the fuel tank.
Use gasoline with a pump octane rating of 90 or higher.
We recommend unEeaded gasoling because it produces
fewer engine and spark plug deposits and extends
exhaust system Eife.
Never use stale or contaminated gasoline or oil/gasoline .....
mixture. Avoid getting dirt or water in the fuel tank.
Owner's Manual
Operation (cont'd)
Starting
4. Operate the Recoil Starter:
Puff the starter grip lightly until you feel resistance,
then pull briskly. Return the starter grip gently.
Pulling the starter grip operates the recoil starter to
crank the engine
5. If the choke has been moved to the "Start"
position to start the engine, gradually move it to the
"Run" position as the engine warms up.
Stopping Engine
1. Turn the engine switch to the "Stop" position,
2. Turn the fuel valve lever to the OFF position.
6000W Generator
Operation (cont'd)
Starting
1, Turn the engine switch to the "RUN" position.
The engine switch enables and disables the ignition
system.
STOP: To stop the engine
RUN: To run the engine
2. The fuel valve is located under the fuel tank . When
the valve lever is in the ON position, fuel is allowed
When the engine is not in use, leave the fuel valve in
the OFF position to prevent carburetor flooding and to
reduce the possibility of fuel leakage.
to flow from the fuel tank to the carburetor. Be sur
to return the fuel valve lever to the OFF position after
stopping the engine.
3. To start a cold engine, move the choke lever to the
"Start" position. To restart a warm engine, leave the
choke lever in the "RUN" position.
The choke lever opens and closes the choke valve in
the carburetor.
The "Start" position enriches the fuel mixture from
starting a cold engine.
CAUTION: ATTEMPTING TO POWER SENSITIVE ELECTRONIC EQUIPMENT
_ tTHOUT THE USE OF AN APPROVED LINE CONDITIONER MAY CAUSE
DAMAGE TO THE EQUIPMENT. ALL-POWER IS NOT RESPONSIBLE FOR
ANY DIRECT OR INDIRECT DAMAGE CAUSED BY FAILURE TO USE AN
APPROVED LINE CONDITIONER.
2. Once the generator is running, simply connect the power cords of 120 volt AC powered
tools and equipment into the 120 volt AC dual outlets.
_ NOTE:THEGENERATORFEATURESAN AC NON-FUSETRERMAL PROTECTOR
TOPROTECTTRE AC CIRCUITIN CASEOFAN OVERLOAD.SHOULD
AN OVERLOADOCCUR,THEBREAKERWILL POP.
3.Disconnect all electrical powered tools and equipment from the generator's 120 volt AC
duel outlets.
4.After the engine and generator have completely cooled, store generator in a safe,clean,dry
location (if not already installed).
1. Prior to powering tools and equipment, make sure the generatoCs rated voltage, and amperage
capacity (120 V AC @ 41.7 AMPs) is adequate to supply all electrical loads that the unit will
power. If powering exceeds the generatods capacity, it may be necessary to group one or more
of the tools and/or equipment for connection to a separate generator.
Operation (cont'd)
Powering 120 Volt AC Tools And Equipment:
6000W Generator
The "RUN" position provides the correct fuel mixture
for operation after starting, and for restarting a warm
engine.
Loading ...
Loading ...
Loading ...