Loading ...
Loading ...
Loading ...
37
ENGLISH
SPECIFICATIONS
Problem Possible Causes Solutions
Wrinkling
y
Did you remove the load immediately after it finished?
y
Did you overload the tub?
y
Did you reverse the hot and cold water inlets?
y
Remove the load immediately after it finishes.
y
Do not overload the tub.
y
Hot water rinse can cause garments to wrinkle. Check
the inlet hose connections.
Power is not turned on
y
Is the power cord plugged in properly?
y
Has a house fuse blown, a circuit breaker tripped, or a
power outage occurred?
y
Make sure that the plug is secured in a grounded
3-prong, 120 V (60 Hz) outlet.
y
Reset the circuit breaker or replace the fuse. Do not
increase the fuse capacity. If the problem is a circuit
overload, have it corrected by a qualified electrician.
The door does not open when the
cycle pauses or finishes
y
Is the temperature in the tub too high?
y
Is the water level in washer high?
y
The washing machine has a safety lock built into the
door to prevent burning. Leave the door closed and wait
until the door lock icon disappears from the display.
y
Allow the washer to complete the programmed cycle,
or Press the SPIN button.
The wash cycle time is longer than
usual
y
Is the washing machine overloaded? Are other options
added to the wash cycle?
y
This is normal. The washing machine automatically
adjusts the cycle time for the amount of laundry, water
pressure, water temperature, and other operating
conditions.
It is musty or moldy in the tub
y
Has the incorrect detergent been used?
y
Did you clean the tub periodically?
y
Use only HE (High-Efficiency) detergent recommended
for a front-loading washing machine.
y
See page 30, clean the inside and outside of the
washing machine periodically.
Banging noise when washer is filling
with water (Water Hammer)
y
Plumbing in the home moves or flexes when the water
valves in the washer shut off.
y
Household water supply pressure is very high.
y
Water hammer is not caused by a defect in the washer.
Install water hammer arrestors (purchased separately at
hardware or home improvement store) between the fill
hose and the washer for best results.
y
Adjust household water supply regulator to a lower
pressure or contact a plumber to have a regulator
installed.
Strange odors coming from
washer
y
First time using washer
y
Buildup of dirt on gasket or drum, dirty or
clogged drain pump filter, kinked or clogged
drain hose
y
Odor is from the rubber door gasket and seal. It will
eventually dissipate after first couple of wash cycles.
y
Periodically clean the gasket. Mold and foreign substances
inside the gasket may produce mildew or musty smells.
y
Clean the drain pump filter regularly. Foreign substances
on the drain pump filter may produce mildew or musty
smells.
y
If the drain hose is not installed properly, the odor may be
emitted because of a backflow of drainage into the tub.
Make sure that the drain hose is not kinked or clogged.
SPECIFICATIONS
Model WM4370H*A
Description Front-Loading Washer
Electrical requirements 120 VAC @ 60 Hz.
Max. water pressure 20–120 psi (138–827 kPa)
Dimensions 68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 132.2 cm (D with door open)
27” (W) X 29 ¾” (D) X 38 ¹¹/
16
” (H), 52" (D with door open)
Net weight 202.8 lbs (92 kg)
Max. spin speed 1,300RPM
MFL68005550_E.indd 37 16. 7. 28. 오후 10:30
Loading ...
Loading ...
Loading ...