Loading ...
Loading ...
Loading ...
To use washer again:
1. Flush water pipes.
2. Reconnect water inlet hoses to faucets.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
5. Runthe washer through the NORMAL/CASUAL cycle with ½
the normal recommended amount of HE detergent to clean
out antifreeze.
To transport the washe_.
1. If washer will be moved during freezing weather, put in 1 qt
(1 L)of R.V-type antifreeze in the drum. Run washer on a
DRAIN/SPIN cycle.
2. Unplug the power cord.
3. Disconnect the drain hose from the drain system and attach
to rear panel clips.
4. Shut off both water faucets.
5. Disconnect the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
6. IMPORTANT: Call Service. Do not reuse transport bolts. Unit
must be transported in the upright position.
Reinstalling the washer
1. Follow the "Installation Instructions" to locate, level and
connect the washer.
2. Runthe washer through the NORMAL!CASUAL cycle with ½
the normal recommended amount of HE detergent to clean
the washer and remove the antifreeze, if used.
TROUBLESHOOTING
FirsttW the solutions suggested here to possibly avoid the cost of a service call...
Washer displaying code message and tone sounds
Washer won't start
"FH" ONater Inlet Problem--no water or insufficient water
supply)
Select PAUSE/OFF twice to cancel the cycle. Unplug washer
or disconnect power.
Check the following:
Are water faucets completely turned on?
Are screens at inlet hose connection to washer clogged?
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug inwasher or reconnect powen Re-select cycle and press
HOLD TO START. Ifthe problem remains, call for service.
"FO2" (Drain Problem)
Select PAUSE/OFF twice to cancel the cycle. Unplug washer
or disconnect power.
Check the following:
Isthe drain hose kinked?
Isthe drain hose frozen?
Isthe drain hose clogged?
Isthe drain hose more than 96" (2.4 m) above the floor?
"SUD" (Suds Routine)
When excessive suds are detected, asuds routine
automatically starts. This routine removes extra suds and
assures proper rinsing of your garments. "SUD" is displayed
during rinsing and at the end of the cycle to inform you that
Suds Routine was activated. To avoid excessive sudsing, use
only HE detergents.
"F" Variables [F4 to F16] (Electrical Problem)
Select PAUSE/OFF twice to cancel the cycle. Select DRAIN/
SPIN ifthere is excessive water in the washer.
Re-select cycle and press HOLD TO START. If the problem
remains, call for service.
• Check the following:
Isthe power cord plugged into a grounded 3 prong outlet?
Isthe washer door firmly closed?
Has a cycle been selected, but HOLD TO START has not
been selected and held for one second?
Was the door open after completion of last cycle?
Washer won't fill, wash or rinse
• Check the following:
Isthe power cord plugged into a grounded 3 prong outlet?
Isthere power at the plug? Check electrical source or call
electrician.
Are the hot and cold water faucets turned on?
Isthe water inlet hose kinked?
Are the water inlet valve screens clogged?
Washerstops
• Check the following:
Isthe power cord plugged into a grounded 3 prong outlet?
Isthere power at the plug?
Check electrical source or call electrician.
Has a fuse blown or has the circuit breaker tripped?
If problem continues, call electrician.
Are you using an extension cord?
Do not use an extension cord.
17
Loading ...
Loading ...
Loading ...