Loading ...
Loading ...
Loading ...
How much detergent to use
• The amount of detergent to use depends on the hardness of
your water and the type of detergent. If you use too little,
dishes won't be clean. If you use too much in soft water,
glassware will etch.
• Water hardness can change over a period of time. Find out
your water's hardness by asking your local water department,
water softener company, or county extension agent.
Where to fill
Top of 3rd step (9 tsp or 45 mL)
Top of 2nd step (6 tsp or 30 mL)
Top of 1st step (3 tsp or 15 mL)
Rinse aids prevent water from forming droplets that can dry as
spots or streaks. They also improve drying by allowing water to
drain off of the dishes during the final rinse by releasing a small
amount of the rinse aid into the rinse water. Your dishwasher is
designed to use a liquid rinse aid. Do not use a solid or bar-type.
Checking the dispenser
Check the center of the Fill Indicator cap. Clear means it needs
filling.
OR
NOTE: Fill amounts shown are for standard powdered detergent.
Amounts may vary if you use liquid or concentrated powdered
detergent. Tablet detergents should be placed in the main wash
section of the detergent dispenser with the cover closed. Follow
instructions on the package when using liquid dishwasher
detergent, concentrated powdered detergent or tablet detergent.
Soft to Medium Water (0-6 grains per gallon)
[typical water softener water and some city water]
Soil Level Main Wash Pre-Wash
Lightly-soiled/Pre- 3 tsp (15 mL) 3 tsp (15 mL)
rinsed dishloads [top of 1st step] [top of 1st step]
Normally-soiled 6 tsp (30 mL) 6 tsp (30 mL)
dishloads [top of 2nd step] [top of 2nd step]
Heavily-soiled 9 tsp (45 mL) 6 tsp (30 mL)
dishloads [top of 3rd step] [top of 2nd step]
Medium to Hard Water (7-12 grains per gallon) t
[well water and some city water]
Soil Level Main Wash Pre-Wash
All soil types 9 tsp (45 mL) 6 tsp (30 mL)
[top of 3rd step] [top of 2rid step]
tTurn the rinse aid dispenser to a higher setting as needed. (See
"Rinse Aid Dispenser" section.) It might be necessary to use the
Pots Pans or Normal cycle with the Hi Temp Scrub option for
best wash performance in very hard water.
Or you can remove the Fill Indicator cap. If an "E" is visible, the
dispenser is empty.
Filling the dispenser
The rinse aid dispenser holds 6 oz (175 mL) of rinse aid. Under
normal conditions, this will last for about three months. You do
not have to wait until the dispenser is empty to refill it. Try to keep
it full, but be careful not to overfill it.
1. Make sure the dishwasher door is completely open.
2. Remove the Fill Indicator cap.
3. Add rinse aid. Fill to the smallest opening in the lower part of
the dispenser. Overfilling can cause the rinse aid to leak out,
and could cause oversudsing.
4. Clean up any spilled rinse aid with a damp cloth.
5. Replace the Fill Indicator cap. Close tightly.
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing results, water should be 120°F
(49°C) as it enters the dishwasher. Loads may not wash as well if
the water temperature is too low. Water that is too hot can make
some soils harder to remove and cause certain detergent
ingredients not to function. If your water heater is located far from
the dishwasher, it may be necessary to run the hot water at the
faucet closest to the dishwasher to minimize the amount of cold
water in the water line.
11
Loading ...
Loading ...
Loading ...