Loading ...
Loading ...
Loading ...
5. HEALTH AND SAFETY INFORMATION9. BASIC OPERATION
Warning!
● Wear appropriate ear protection. Exposure to noise can lead to hearing loss.
● There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the
power tool.
● Do not touch the drill bit or areas close to the drill bit immediately after use; they
can still be extremely hot, causing burns.
- 7 -- 14 -
9.1 SDS
+
SYSTEM – FIGS.4 – 5
The tool holder
clamps SDS+ drill bits without
the need for a chuck key.
– Pull collar
back.
– Insert the bit. It may be necessary to rotate the
bit to ensure it engages correctly.
– Release the collar to lock the bit in place. Check
by pulling the bit to see if it’s firmly seated.
Important: Always clean and lightly grease the tool
shaft before inserting into the chuck.
Take care that the dust protection cap is not
damaged. Allowing dust and debris inside the holder
will cause problems in the future.
– To remove a drill bit, slide the collar
to the
rear and pull out the tool.
9.2 ROTATIONAL DRIVE SELECTION –
FIG.6
The forward/reverse drive selector switch
determines the direction of rotation of the drive, i.e.
clockwise or anticlockwise.
To alter the direction of rotation:
– Stop the machine and push switch
to the left
or right.
– When the direction switch is pushed to the left,
the drive will rotate clockwise.
– When the switch is pushed to the right, the drive
will rotate anticlockwise.
– Before operation, check that the switch is set in
the required position. Do not change the
direction of rotation until the driver comes to a
complete stop.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged
or missing parts immediately with original parts from the manufacturer. As applicable; keep blades
sharp; moving parts clean, oiled or greased; handles clean; and emergency devices working.
Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts may
continue to move due to momentum. Wait for all parts to stop; then unplug it from the power
supply before making any adjustments, carrying out maintenance operations or just finishing using
the tool.
Remove and check setting tools. Some machinery requires the use of additional tools or keys to
set, load or adjust the power tool. Before starting the power tool always check to make certain they
have been removed and are safely away from the machine.
Prevent unintentional starting. Before plugging any machine in to the power supply, make sure
the switch is in the OFF position. If the machine is portable; do not hold the machine near the
switch and take care when putting the machine down; that nothing can operate the switch.
Carefully select an extension lead. Some machines are not suitable for use with extension
leads. If the tool is designed for use outdoors; use an extension lead also suitable for that
environment. When using an extended lead, select one capable of handling the current (amps)
drawn by the machine in use. Fully extend the lead regardless of the distance between the power
supply and the tool. Excess current (amps) and a coiled extension lead will both cause the cable
to heat up and can result in fire.
Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power
tool if you are under the influence of drugs (prescription or otherwise), including alcohol or if you
are feeling tired. Being disorientated will result in an accident.
Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains
safe to use.
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS
Important: Draper Tools Limited recommends that this machine should not be modified or used
for any application other than that for which it was designed. If you are unsure of its relative
applications do not hesitate to contact us in writing and we will advise you.
– Power tools shall not be used in potentially explosive atmospheres unless specifically designed
for that purpose.
– Unexpected tool movement due to reaction forces or breakage may cause injuries.
– Power tools shall be isolated from the energy source before changing or adjusting the inserted
tool.
FIG.6
FIG.4
– Be sure the drill bit is securely in place before using the drill.
– There is a risk of release of toxic chemicals into the atmosphere when using certain materials.
Always be mindful to use the appropriate personal protective wear to help safeguard against
potential skin contact and dust inhalation. Always consult and follow the material supplier’s
safety guidelines.
FIG.5
++++++
+
++
++++
+
+++++++
++++++
+
+
++++
++
+
+
++++++++
Loading ...
Loading ...
Loading ...