Loading ...
Loading ...
Loading ...
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher runs the last full
wash cycle and options.
TURBOZONE TM wash option
Select this option to activate the TURBOZONETM spray jets and
provide intensified water spray to the back of the lower dishrack.
The TURBOZONE TM wash option provides a concentrated wash
action to pans, casseroles, etc. with tough food soil.
This option may add heat and wash time to the cycle.
NOTE: TURBOZONETM is an option with the SMART WASW M,
Pots Pans, and Normal Wash cycles.
IMPORTANT:
• Load pans, casserole dishes, etc. facing the TURBOZONETM
spray jets in the back of the lower dishrack. Tip items toward
the rear of the dishrack to maximize coverage. Only one row
of items may face the TURBOZONETM spray jets. Stacking,
overlapping, or nesting items will prevent the TURBOZONETM
spray jets from reaching all of the surfaces.
• Turn the TURBOZONETM wash option off if not loading items
for this option.
Side view of TURBOZONETM wash area
Hi Temp Wash
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp Wash raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. Hi Temp Wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp Wash is an option with the SMART WASH TM,
Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSl Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH TM, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSl requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher
between cycles.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours/4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, press START/RESUME. Make sure the
door is latched or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL/DRAIN.
To cancel the delay and start the cycle, press START/
RESUME.
On top control models, if the door is not closed within
3 seconds of pressing Start/Resume, press START/RESUME
again.
16
Loading ...
Loading ...
Loading ...